Engineering Papers⌕ Search

Engineering topics

Rivera, J.

Publications and source records attributed to Rivera, J..

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Production of Readily Compressible Dies for the Enhanced Sintering of Solids (PRESS) Preliminary Investigations

Non-oxide ceramics, which consist of predominantly carbides, borides, and nitrides, are of great interest to modern engineering because of their resistance to extreme conditions. Properties of such materials include high temperature resistance, high hardness, chemical resistance, and high fracture toughness. However, the main method for manufacturing parts of these materials is by machining cylindrical billets to the desired geometry. Not only does this produce waste, but the cost of machining is high since the part materials are of such high hardness. This method is used because these non-oxide ceramics must be sintered to high density using simultaneous heat and pressure within a hot-pressing unit. These units are inherently restricted to cylindrical geometries. A proposed way to expand the capabilities of a hot-press is by using intermediate compressible dies. This method consists of surrounding a ceramic part green body with a material that will shrink at the same rate as the part and survive the hot-pressing conditions. At the end, the compressible die material would be removed leaving a nearly net shaped hot-pressed part. In this study, graphite powder was investigated as the compressible die material with its shrinkage rate being controlled by particle size mixing. Both ceramic materials and graphite were then cast into parts and compressible dies respectively to show the feasibility of the compressible die hot-pressing method.

36 MATERIALS SCIENCE↗
NASA NTRS2019

The Space Debris Sensor Experiment

The Space Debris Sensor (SDS) is a NASA Class 1E technology demonstration external payload aboard the International Space Station (ISS). With approximately one square meter of detection area, the SDS is attached to the European Space Agency Columbus module facing the ISS velocity vector with minimal obstruction from ISS hardware. The SDS is the first flight demonstration of the Debris Resistive/Acoustic Grid Orbital NASA-Navy Sensor (DRAGONS) technology developed and matured over 10 years by the NASA Orbital Debris Program Office (ODPO), in concert with the DRAGONS consortium, to provide information on the sub-millimeter scale orbital debris environment. The SDS demonstrated the capacity to read 4 resistive grids at 1 Hz, 40 acoustic sensors at 500 kHz, and record and downlink impact data to the ground. Observable and derived data from the SDS could provide information to models that are critical to understanding risks the small debris environment poses to spacecraft in low Earth orbit. The technology demonstrated by the SDS is a major step forward in monitoring and characterizing the space debris environment. This paper will address the technical performance of the SDS during its operational lifetime and its realization of technical and scientific goals. The SDS was intended to operate for 3 years; however, the payload incurred multiple anomalies during its operational life. Subsequently termed “Anomaly #1,” the first was the symptomatic loss of low data rate 1553 channel command and telemetry. The second, Anomaly #2, was loss of all low- and medium-data rate (Ethernet) telemetry. Anomaly #2 proved to be unrecoverable, leading to loss of the payload after approximately 26 days on-board the ISS. Therefore, this paper also addresses the anomalies that occurred during operation of the SDS, their attribution, and their resolution. Lessons learned are described when relevant to anomaly identification, attribution, and resolution.

Anz-Meador, P.↗
NASA NTRS2017

Multiwavelength Characterization of an ACT-Selected, Lensed Dusty Star-Forming Galaxy at zeta 2.64

We present C I(21) and multi-transition C-12 O observations of a dusty star-forming galaxy, ACT J2029+0120,which we spectroscopically confirm to lie at zeta = 2.64. We detect CO(3-2), CO(5-4), CO(7-6), CO(8-7), and C I(2-1) at high significance, tentatively detect HCO+(4-3), and place strong upper limits on the integrated strength of dense gas tracers (HCN(4-3) and CS(7-6)). Multi-transition CO observations and dense gas tracers can provide valuable constraints on the molecular gas content and excitation conditions in high-redshift galaxies. We therefore use this unique data set to construct a CO spectral line energy distribution (SLED) of the source, which is most consistent with that of a ULIRG Seyfert or QSO host object in the taxonomy of the Herschel Comprehensive ULIRG Emission Survey. We employ RADEX models to fit the peak of the CO SLED, inferring a temperature of T approximately 117 K and n(sub H2) approximately 10(exp5) cm(exp -3), most consistent with a ULIRGQSO object and the presence of high-density tracers. We also find that the velocity width of the C I line is potentially larger than seen in all CO transitions forth is object, and that the L'(sub Ci(2-1))/L'(sub CO(3-2))ratio is also larger than seen in other lensed and unlensed submillimeter galaxies and QSO hosts; if confirmed, this anomaly could be an effect of differential lensing of a shocked molecular outflow.

Roberts-Borsani, G. W.↗