Engineering Papers⌕ Search

Engineering topics

Rietema, Connor J.

Publications and source records attributed to Rietema, Connor J..

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A New Method for Creating Structured High-Performance Current Collectors for Electrochemical Applications

A significant challenge in many electrochemical systems is finding a stable, high-performing current collector material that is mechanically robust, adaptable in form factor, and free of precious metals. Titanium electrodes are robust in many of these regards but exhibit poor charge transfer performance due to self-passivation. Herein, a new materials processing paradigm based on the titanium/titanium nitride (Ti/TiN) system which allows for robust, stable, and low-resistance current collectors of arbitrary form factor is presented. Specifically, a gas-nitriding process for 3D-printed titanium electrodes that results in a 20-fold improvement of charge transfer characteristics relative to the untreated material is outlined. The ability to utilize 3D-structured current collectors with a net 40-fold improvement in performance over nonstructured electrodes is further demonstrated. This novel approach to creating electrochemical current collectors requires minimal laboratory resources and can be widely adapted for a variety of applications, including desalination, electrolysis, energy storage, and basic research. In conclusion, the work described herein provides both a means for accelerating research and opens the door to hierarchical tuneability for enhanced performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhanced magnetostriction through dilute Ce doping of Fe-Ga

Doping of magnetostrictive galfenol (Fe 82 Ga 18 , in at.%) with rare-earth elements significantly enhances magnetostriction, with the largest gains achieved in textured melt-spun ribbons. Here, it is demonstrated that even extremely dilute Ce, as little as 65 ppm, can double the magnetostrictive response of galfenol when coupled with an appropriate heat treatment. This improvement is correlated with a compression of the host lattice, both of which reach their maximum extent at the calculated solubility limit of Ce in in body-centered cubic (bcc) galfenol, ~ 50 ppm. Beyond this point, excess Ce segregates into CeGa 2 , which forms an interdendritic network throughout the sample at high Ce levels and cannot be resolutionized through heat treatments. These findings point to the importance of solubility limits (i.e., equilibrium thermodynamics) in determining appropriate doping levels or heat treatment couples to optimize magnetostrictive performance, confirming that overdoping is actively detrimental to both material properties and cost.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High strain rate deformation of aged TRIP Ti-10V-2Fe-3Al (wt.%) examined by in-situ synchrotron X-ray diffraction

Transformation Induced Plasticity (TRIP) is a promising avenue for tailoring the work hardening response of metastable $β$ titanium (Ti) alloys. Here we show that aged TRIP Ti-10V-2Fe-3Al (wt.%) maintains higher elongations and flow stresses as strain rate increases, if phase stability and microstructural characteristics are tuned. Low temperature aging influences the matrix $β$ phase stability by $ω$ phase precipitation, which affords a promising way to impact the TRIP effect and obtain desirable mechanical properties, ranging from high damping capacity to good strength/ductility combinations. Although TRIP is active during quasi-static and dynamic testing up to 2000 s –1 , increasing aging time and/or strain rate reduces the overall propensity for the TRIP effect and extent of transformation, which occurs rapidly just at the onset of yielding. Importantly, TRIP with $ω$ phase precipitation provides interesting alloying, microstructure, and property design strategies for engineering applications like lightweight protective structures, where high strains and the need for energy absorption are encountered.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Void swelling of conventional and composition engineered HT9 alloys after high-dose self-ion irradiation

Ferritic/martensitic (F/M) steels are being considered as potential structural materials for next generation nuclear reactors, and variants of the alloy HT9 are some of the most promising candidates. In this study, two conventional and two composition engineered HT9 alloys were irradiated using 3.5 MeV Fe 2+ up to 600 peak displacement-per-atom (dpa) at 450 °C. Void swelling and microstructure evolution were characterized for each alloy and compared. The two conventional HT9 alloys (INL and ACO3) showed similar void swelling behavior due to their similar elemental composition and processing conditions. The INL HT9 exhibited a maximum of 2.4% swelling and the ACO3 HT9 showed a maximum of 2.8% swelling at 342 and 393 average local dpa, respectively. On the other hand, the two-composition engineered HT9 alloys with varying N contents (10 ppm for low N and 440 ppm for high N) showed disparate swelling behavior. The low N HT9 exhibited a maximum of 4.6% swelling, while the high N HT9 showed a maximum of 0.7% swelling at 342 average local dpa. Changes in the N content also affected Ni/Si rich G-phase formation. The low N HT9 showed a larger size and lower density of G-phase precipitates compared with the high N HT9 after 600 peak dpa irradiation. This study compares the void swelling behavior of the ion irradiated four current HT9 alloys to extremely high doses, with the void swelling data from neutron irradiated HT9 alloys. Furthermore, the comparison lends critical insights into how well these current alloys can withstand high neutron fluxes in future reactors, especially since the low N and high N HT9 alloys have never been exposed to such high doses before.

36 MATERIALS SCIENCE↗