Engineering topics
Publications and source records attributed to Rice, Tharen.
This report details the development of a 2D and 3D Method of Characteristic (MOC) tool for the design of complex nozzle geometries. These tools are GUI driven and can be run on most Windows-based platforms. The report provides a user's manual for these tools as well as explains the mathematical algorithms used in the MOC solutions.
Under sponsorship of the NASA Glenn Research Center (NASA GRC), the Johns Hopkins University Applied Physics Laboratory (JHU/APL) designed and built a five-inch diameter, Rocket-Based Combined Cycle (RBCC) engine to investigate mode 1 and mode 4 engine performance as well as Mach 4 inlet performance. This engine was designed so that engine area and length ratios were similar to the NASA GRC GTX engine is shown. Unlike the GTX semi-circular engine design, the APL engine is completely axisymmetric. For this design, a traditional rocket thruster was installed inside of the scramjet flowpath, along the engine centerline. A three part test series was conducted to determine Mode I and Mode 4 engine performance. In part one, testing of the rocket thruster alone was accomplished and its performance determined (average Isp efficiency = 90%). In part two, Mode 1 (air-augmented rocket) testing was conducted at a nominal chamber pressure-to-ambient pressure ratio of 100 with the engine inlet fully open. Results showed that there was neither a thrust increment nor decrement over rocket-only thrust during Mode 1 operation. In part three, Mode 4 testing was conducted with chamber pressure-to-ambient pressure ratios lower than desired (80 instead of 600) with the inlet fully closed. Results for this testing showed a performance decrease of 20% as compared to the rocket-only testing. It is felt that these results are directly related to the low pressure ratio tested and not the engine design. During this program, Mach 4 inlet testing was also conducted. For these tests, a moveable centerbody was tested to determine the maximum contraction ratio for the engine design. The experimental results agreed with CFD results conducted by NASA GRC, showing a maximum geometric contraction ratio of approximately 10.5. This report details the hardware design, test setup, experimental results and data analysis associated with the aforementioned tests.
The development of rocket based combined cycle (RBCC) engines are highly dependent upon integrating several different modes of operation into a single system. Due to the integrated nature of the propulsion system, each operating mode relies on the same expansion system to provide thrust. A fixed geometry, altitude-compensating aft-expansion configuration is used for the GTX flowpath configuration. Initial studies on the GTX expansion designs have demonstrated the importance of a smooth, highly integrated design for propulsion system performance. Based upon the results from the initial studies, further design improvements were made to the expansion system. Nozzles designed based on both conical and streamline traced flowfields; are discussed. Results from 3-D CFD calculations on an optimized geometry are also presented. A series of cold-flow experiments are proposed to validate the CFD analysis and quantify performance of the flowpath expansions surface design. A discussion is provided of the research hardware designs and experimental test plans.
Under sponsorship of the NASA Glenn Research Center (NASA GRC), the Johns Hopkins University Applied Physics Laboratory (JHU/APL) designed and built a five-inch diameter, Rocket-Based Combined Cycle (RBCC) engine to investigate mode 1 and mode 4 performance. This engine was designed so that engine area and length ratios were similar to the NASA GRC GTX engine. Unlike the GTX semi-circular engine design, the APL engine is completely axisymmetric. For this design, a traditional rocket thruster was installed inside of the scramjet flowpath, along the engine centerline. A three part test series is currently underway to determine mode 1 and mode 4 engine performance and compare those results to the rocket thruster operating by itself. All tests are to be conducted in APL's Cell 2 Freejet Engine Facility. Testing of the rocket thruster alone has been accomplished and its performance determined (average Isp efficiency = 90%). Mode 1 (air-augmented rocket) testing is to be conducted at various chamber pressure-to-ambient pressure ratios with the engine inlet fully open. Mode 4 (vacuum rocket) testing is to be conducted with chamber pressure-to-ambient pressure ratios greater than 600 with the inlet fully closed to simulate high-altitude flight conditions. The engine is currently installed in Cell 2 and awaiting testing. This paper discusses the engine design and details the results of the rocket-only testing. Comparisons to previous tests and projected mode 1 and mode 4 test conditions are also discussed.
The development of rocket based combined cycle (RBCC) engines is highly dependent upon integrating several different modes of operation into a single system. One of the key components to develop acceptable performance levels through each mode of operation is the nozzle. It must be highly integrated to serve the expansion processes of both rocket and air-breathing modes without undue weight, drag, or complexity. The NASA GTX configuration requires a fixed geometry, altitude-compensating nozzle configuration. The initial configuration, used mainly to estimate weight and cooling requirements was a 1 So half-angle cone, which cuts a concave surface from a point within the flowpath to the vehicle trailing edge. Results of 3-D CFD calculations on this geometry are presented. To address the critical issues associated with integrated, fixed geometry, multimode nozzle development, the GTX team has initiated a series of tasks to evolve the nozzle design, and validate performance levels. An overview of these tasks is given. The first element is a design activity to develop tools for integration of efficient expansion surfaces With the existing flowpath and vehicle aft-body, and to develop a second-generation nozzle design. A preliminary result using a "streamline-tracing" technique is presented. As the nozzle design evolves, a combination of 3-D CFD analysis and experimental evaluation will be used to validate the design procedure and determine the installed performance for propulsion cycle modeling. The initial experimental effort will consist of cold-flow experiments designed to validate the general trends of the streamline-tracing methodology and anchor the CFD analysis. Experiments will also be conducted to simulate nozzle performance during each mode of operation. As the design matures, hot-fire tests will be conducted to refine performance estimates and anchor more sophisticated reacting-flow analysis.