Engineering Papers⌕ Search

Engineering topics

Rice, Edward J.

Publications and source records attributed to Rice, Edward J..

35 records · Page 2

Control of an axisymmetric turbulent jet by multi-modal excitation

Experimental measurements of naturally occurring instability modes in the axisymmetric shear layer of high Reynolds number turbulent jet are presented. The region up to the end of the potential core was dominated by the axisymmetric mode. The azimuthal modes dominated only downstream of the potential core region. The energy content of the higher order modes (m is greater than 1) was significantly lower than that of the axisymmeteric and m = + or - 1 modes. Under optimum conditions, two-frequency excitation (both at m = 0) was more effective than single frequency excitation (at m = 0) for jet spreading enhancement. An extended region of the jet was controlled by forcing combinations of both axisymmetric (m = 0) and helical modes (m = + or - 1). Higher spreading rates were obtained when multi-modal forcing was applied.

Raman, Ganesh↗

Naturally occurring and forced azimuthal modes in a turbulent jet

Naturally occurring instability modes in an axisymmetric jet are studied utilizing the modal frequency spectrum method. In the early evolution of the jet the axisymmetric mode was predominant, with the azimuthal modes growing quickly but dominating only after the end of the potential core. The growth of the azimuthal modes is seen nearer to the nozzle exit for the jet in the laminar boundary layer case than for the turbulent. Based on the results from these naturally occurring jet instability mode tests, target modes for efficient excitation were determined and two cases of excitation were examined.

Raman, Ganesh↗

Control of an axisymmetric turbulent jet by multi-modal excitation

Experimental measurements of naturally occurring instability modes in the axisymmetric shear layer of high Reynolds number turbulent jet are presented. The region up to the end of the potential core was dominated by the axisymmetric mode. The azimuthal modes dominated only downstream of the potential core region. The energy content of the higher order modes (m is greater than 1) was significantly lower than that of the axisymmetric and m = + or - 1 modes. Under optimum conditions, two-frequency excitation (both at m = 0) was more effective than single frequency excitation (at m = 0) for jet spreading enhancement. An extended region of the jet was controlled by forcing combinations of both axisymmetric (m = 0) and helical modes (m = + or - 1). Higher spreading rates were obtained when multi-modal forcing was applied.

Raman, Ganesh↗

Inlets, ducts, and nozzles

The internal fluid mechanics research program in inlets, ducts, and nozzles consists of a balanced effort between the development of computational tools (both parabolized Navier-Stokes and full Navier-Stokes) and the conduct of experimental research. The experiments are designed to better understand the fluid flow physics, to develop new or improved flow models, and to provide benchmark quality data sets for validation of the computational methods. The inlet, duct, and nozzle research program is described according to three major classifications of flow phenomena: (1) highly 3-D flow fields; (2) shock-boundary-layer interactions; and (3) shear layer control. Specific examples of current and future elements of the research program are described for each of these phenomenon. In particular, the highly 3-D flow field phenomenon is highlighted by describing the computational and experimental research program in transition ducts having a round-to-rectangular area variation. In the case of shock-boundary-layer interactions, the specific details of research for normal shock-boundary-layer interactions are described. For shear layer control, research in vortex generators and the use of aerodynamic excitation for enhancement of the jet mixing process are described.

Abbott, John M.↗

Control of flow separation and mixing by aerodynamic excitation

The recent research in the control of shear flows using unsteady aerodynamic excitation conducted at the NASA Lewis Research Center is reviewed. The program is of a fundamental nature, concentrating on the physics of the unsteady aerodynamic processes. This field of research is a fairly new development with great promise in the areas of enhanced mixing and flow separation control. Enhanced mixing research includes influence of core turbulence, forced pairing of coherent structures, and saturation of mixing enhancement. Separation flow control studies included are for a two-dimensional diffuser, conical diffusers, and single airfoils. Ultimate applications include aircraft engine inlet flow control at high angle of attack, wide angle diffusers, highly loaded airfoils as in turbomachinery, and ejector/suppressor nozzles for the supersonic transport. An argument involving the Coanda Effect is made that all of the above mentioned application areas really only involve forms of shear layer mixing enhancement. The program also includes the development of practical excitation devices which might be used in aircraft applications.

Rice, Edward J.↗

Phase development and its role on subharmonic control

The conditions for resonance interaction between two instability waves in an axisymmetric jet were investigated. Considerations of the energy equation of the wave resulting from the interaction indicate that the phase angle between the wave-induced stresses and the wave-induced strains plays a crucial role in the resonance interaction. This fact is demonstrated experimentally by exciting a jet at fundamental and subharmonic frequencies. The phase angle between the waves' stresses and strains was varied by varying the initial phase-difference between the two excitation waves. The subharmonic resonance was found to be highly dependent on this angle. Favorable agreement was found between the phase angles predicted by a nonlinear theory and the measured ones. The theory is used to explain the subharmonic's resonance in terms of the phase-angles.

Mankbadi, Reda R.↗

Effects of fiber motion on the acoustic behavior of an anisotropic, flexible fibrous material

The acoustic behavior of a flexible fibrous material was studied experimentally. The material consisted of cylindrically shaped fibers arranged in a batting with the fibers primarily aligned parallel to the face of the batting. This type of material was considered anisotropic, with the acoustic propagation constant depending on whether the direction of sound propagation was parallel or normal to the fiber arrangement. Normal incidence sound absorption measurements were taken for both fiber orientations over the frequency range 140 to 1500 Hz and with bulk densities ranging from 4.6 to 67 kg/cu m. When the sound propagated in a direction normal to the fiber alignment, the measured sound absorption showed the occurrence of a strong resonance, which increased absorption above that attributed to viscous and thermal effects. When the sound propagated in a direction parallel to the fiber alignment, indications of strong resonances in the data were not present. The resonance in the data for fibers normal to the direction of sound propagation is attributed to fiber motion. An analytical model was developed for the acoustic behavior of the material displaying the same fiber motion characteristics shown in the measurements.

Dahl, Milo D.↗

Control of flow separation and mixing by aerodynamic excitation

The recent research progress in the control of shear flows using unsteady aerodynamic excitation conducted at the NASA Lewis Research Center is reviewed. The program is of fundamental nature concentrating on the physics of the unsteady aerodynamic processes. This field of research is a fairly new development with great promise in the areas of enhanced mixing and flow separation control. Enhanced mixing research reported in this paper include influence of core turbulence, forced pairing of coherent structures, and saturation of mixing enhancement. Separation flow control studies included are for a two-dimensional diffuser, conical diffusers, and single airfoils. Ultimate applications of this research include aircraft engine inlet flow control at high angle of attack, wide angle diffusers, highly loaded airfoils as in turbomachinery, and ejector/suppressor nozzles for the supersonic transport. An argument involving the Coanda Effect is made here that all of the above mentioned application areas really only involve forms of shear layer mixing enhancement. The program also includes the development of practical excitation devices which might be used in aircraft applications.

Rice, Edward J.↗

Subharmonic and fundamental high amplitude excitation of an axisymmetric jet

A circular jet was excited simultaneously by two different harmonically related tones. Data for three pairs of Strouhal numbers (St(D) = f*D/U (sub j) = 0.2 and 0.4, 0.3 and 0.6, 0.4 and 0.8). For each case the initial phase difference between the two waves was varied in steps of 45 deg, for one full cycle and the level of the fundamental and subharmonic forcing were varied independently over the range of 0.1 to 7 percent of the jet exit velocity. Our initial findings concurred with published findings, such as a critical level of the fundamental is required for subharmonic augmentation, the initial phase difference is critical in determining whether the subharmonic is augmented or suppressed. The detailed documentation of several aspects of this phenomenon all measured in one and the same experimental facility in a controlled manner, bring out several important points that eluded previous researchers: (1) At high amplitudes of the fundamental and subharmonic forcing levels the subharmonic augmentation is independent of the initial phase difference. (2) Contrary to the earlier belief that stable pairing could be produced only with an initial laminar boundary layer, the present work shows that by the two-frequency excitation method this phenomenon can be induced over a range of conditions for a jet with an initially turbulent boundary layer. (3) It is seen that two-frequency excitation is indeed more effective than single frequency excitation in jet mixing enhancement. Higher spreading rates seem to go along with higher subharmonic levels.

Raman, Ganesh↗

Phase development and its role on subharmonic control

The conditions for resonance interaction between two instability waves in an axisymmetric jet were investigated. Considerations of the energy equation of the wave resulting from the interaction indicate that the phase angle between the wave-induced stresses and the wave-induced strains plays a crucial role in the resonance interaction. This fact is demonstrated experimentally by exciting a jet at fundamental and subharmonic frequencies. The phase angle between the waves stresses and strains was varied by varying the initial phase-difference between the two excitation waves. The subharmonic resonance was found to be highly dependent on this angle. Favorable agreement was found between the phase angles predicted by a nonlinear theory and the measured ones. The theory is used to explain the subharmonic's resonance in terms of the phase-angles.

Mankbadi, Reda R.↗

Effects of core turbulence on jet excitability

The effects of varying freestream core turbulence on the evolution of a circular jet with and without tonal excitation are examined. Measurements are made on an 8.8 cm diameter jet at a Mach number of 0.3. The jet is excited by plane waves at Strouhal number 0.5. For the excited and unexcited cases the turbulence level is varied by screens and grids placed upstream of the nozzle exit. The experiment results are compared with a theoretical model which incorporates a variable core turbulence and considers the energy interactions between the mean flow, the turbulence and the forced component. Both data and theory indicate that increasing the freestream turbulence diminishes the excitability of the jet and reduces the effect of excitation on the spreading rate of the jet.

Mankbadi, Reda R.↗

Subharmonic and fundamental high amplitude excitation of an axisymmetric jet

The effect of simultaneous excitation at the fundamental and subharmonic frequencies on the behavior of a circular jet shear layer is studied. Attention is given to the effect of the initial phase difference, the Strouhal number pair, and amplitudes of the fundamental and subharmonic tones. High-amplitude excitation devices which can provide a wide range of forcing conditions when used in conjunction with equipment that produces complex waveforms are used.

Raman, Ganesh↗

Effects of core turbulence on jet excitability

The effects of varying freestream core turbulence on the evolution of a circular jet with and without tonal excitation are examined. Measurements are made on an 8.8 cm diameter jet at a Mach number of 0.3. The jet is excitated by plane waves at Strouhal number 0.5. For the excited and unexcited cases the turbulence level is varied by screens and grids placed upstream of the nozzle exit. The experiment results are compared with a theoretical model which incorporates a variable core turbulence and considers the energy interactions between the mean flow, the turbulence and the forced component. Both data and theory indicate that increasing the freestream turbulence diminishes the excitability of the jet and reduces the effect of excitation on the spreading rate of the jet.

Mankbadi, Reda R.↗

Saturation and the limit of jet mixing enhancement by single frequency plane wave excitation: Experiment and theory

The limitations of single frequency plane wave excitation in mixing enhancement are investigated for a circular jet. Measurements made in an 8.8 cm diameter jet are compared with a theoretical model. The measurements are made to quantify mixing at excitation amplitudes up to 2 percent of the jet exit velocity. The initial boundary layer state, the exit mean and fluctuating velocity profiles and spectra are documented for all cases considered. The amplitude of the fundamental wave is recorded along the jet axis for various levels of excitation. As the amplitude of excitation is increased the jet spreading rate is increased, but beyond a saturation amplitude further increases have no effect on the spreading. The experimental results are compared with theoretical estimates. In the theory the flow is split into the mean flow, large scale motions, and fine scale turbulence. Shape assumptions for the mean flow, and fine scale turbulence along with the shape for the large scale motions obtained from a linear stability theory provide the closure. The experimental results compare reasonably well with predictions.

Raman, Ganesh↗

Saturation and the limit of jet mixing enhancement by single frequency plane wave excitation - Experiment and theory

The limitations of single frequency plane wave excitation in mixing enhancement are investigated for a circular jet. Measurements made in an 8.8 cm diameter jet are compared with a theoretical model. The measurements are made to quantify mixing at excitation amplitudes up to 2 percent of the jet exit velocity. The initial boundary layer state, the exit mean and fluctuating velocity profiles and spectra are documented for all cases considered. The amplitude of the fundamental wave is recorded along the jet axis for various levels of excitation. As the amplitude of excitation is increased the jet spreading rate is increased, but beyond a saturation amplitude further increases have no effect on the spreading. The experimental results are compared with theoretical estimates. In the theory the flow is split into the mean flow, large scale motions, and fine scale turbulence. Shape assumptions for the mean flow, and fine scale turbulence along with the shape for the large scale motions obtained from a linear stability theory provide the closure. The experimental results compare reasonably well with predictions.

Raman, Ganesh↗

Inlets, ducts and nozzles

The internal fluid mechanics research program in inlets, ducts, and nozzles is described. The program consists of a balanced effort between the development of computational tools and the conduct of experimental research. The experiments are designed to better understand the fluid flow physics, to develop new or improved flow models, and to provide benchmark quality data sets for validation of the computational methods. The inlet, duct, and nozzle research program is described according to three major classifications of flow phenomena: highly three-dimensional flow fields; shock-boundary layer interactions; and shear layer control. Specific examples of current and future elements of the research program are described for each of these phenomena. In particular, the highly three-dimensional flow field phenomena is highlighted by describing the computational and experiemental research program in transition ducts having a round-to-rectangular area variation. In the case of shock-boundary layer interactions, the specific details of research for normal shock-boundary layer interactions are described. For shear layer control research in vortex generators and the use of aerodynamic excitation for enhancement of the jet mixing process are described. Future research in inlets, ducts, and nozzles will include more emphasis on three-dimensional full Navier-Stokes methods and corresponding experiments designed to concentrate on the appropriate three-dimensional fluid flow physics.

Abbott, John M.↗

Effects of fiber motion on the acoustic behavior of an anisotropic, flexible fibrous material

The acoustic behavior of a flexible fibrous material was studied experimentally. The material consisted of cylindrically shaped fibers arranged in a batting with the fibers primarily aligned parallel to the face of the batting. This type of material was considered anisotropic, with the acoustic propagation constant depending on whether the dirction of sound propagation was parallel or normal to the fiber arrangement. Normal incidence sound absorption measurements were taken for both fiber orientations over the frequency range 140 to 1500 Hz and with bulk densities ranging from 4.6 to 67 kg/cu m. When the sound propagated in a direction normal to the fiber alignment, the measured sound absorption showed the occurrence of a strong resonance, which increased absorption above that attributed to viscous and thermal effects. When the sound propagated in a direction parallel to the fiber alignment, indications of strong resonances in the data were not present. The resonance in the data for fibers normal to the direction of sound propagation is attributed to fiber motion. An analytical model was developed for the acoustic behavior of the material displaying the same fiber motion characteristics shown in the measurements.

Dahl, Milo D.↗