Engineering topics
Publications and source records attributed to Repukaiti, Reyixiati.
The isolation of Ni/Co double salts can be recovered by fractional precipitation with ammonium sulfate. The elemental analysis of these isolated double salts shows a total metal composition of >99% of Ni, Co, and Mn with negligible impurity metals.
Previous studies demonstrated the corrosion susceptibility of advanced neutron absorber (ANA) Ni-Cr-Mo-Gd in a seawater environment but remained inconclusive. In this paper, scanning electron microscopy was employed to identify the corrosion phase in Ni-Cr-Mo-Gd, and computational thermodynamic simulation was used to study phase corrosion potentials. Results showed that the Ni 5 Gd second phase, distributed along FCC grain boundaries in Ni-Cr-Mo-Gd, has lower corrosion potential than the substrate. Furthermore, heat treatment and alloy chemistry adjustment would not ameliorate the ANA corrosion susceptibility. Finally, isolating the Ni 5 Gd from the corrosion medium through advanced manufacturing is a viable way to improve the ANA corrosion resistance.
Neutron absorbing materials are being considered within commercial spent nuclear fuel disposal canisters to maintain nuclear subcriticality in storage. To select candidate alloys for the canisters, both neutron absorption and corrosion resistance should be considered. This work examines corrosion resistance of Ni-Cr-Mo-Gd alloys developed specifically for neutron absorption. The addition of Gd results in a secondary gadolinide phase (Ni 5 Gd) that significantly changes the corrosion properties. Testing was performed primarily in seawater at 30°C. Seawater was selected as the most prevalent terrestrial brine and is characterized by a high chloride concentration. Various electrochemical corrosion techniques were carried out to evaluate Ni-Cr-Mo-Gd alloys with different Cr compositions and investigate the role of Ni 5 Gd phase on corrosion behavior. C22 was included as a benchmark material, due to the similarity in composition and the significant corrosion data available. Here, test results showed a tendency to passivate over time which is attributed to dissolution of surface exposed Ni 5 Gd phase. Cross-sectional analysis indicated that dissolution could penetrate hundreds of micrometers deep under aggressive conditions. It was found that higher Cr variant (21.01%) showed much shallower impact, suggesting Cr prevented primary phase corrosion and thus reduced Ni 5 Gd phase dissolution. Acid pickling of the specimens showed much less dissolution for a higher Cr material and suggested some primary phase dissolution for the low Cr specimen. Acid pickled specimens showed positive shifts in the repassivation potential, suggesting increased surface passivation.
Recovery of critical materials from end-of life (EOL) lithium-ion batteries (LIB) is gaining interest as demands for materials grows. Hydrometallurgical processes start with an intermediate product known as black mass which contains critical materials of interest (Co, Ni, Li, and graphite) as well as impurities such as Cu, Al, and Fe. These impurities are deleterious to downstream separation processes, as well as impact functionality of the final products. Here, these impurities effectively compete with most solvent extraction (SX) and metal recovery processes to diminish the overall yields of the desired materials. In this work, a process flowsheet is presented where a previously reported electrochemical leaching (ECL) process is followed by selective precipitation using diammonium hydrogen phosphate (DAP) to remove Cu, Al, and Fe from LIB leachate solutions. The electrochemical leach process removes Cu and produces a pH-adjusted leachate, ca. pH 2, without requiring an extra Cu extraction step. The addition of the precipitant DAP to leachate by slightly adjusting the pH to 3–4 at 45 °C, precipitates 95–99% of Al and Fe as their phosphates and the leachate retains >95% of Co, Ni and Li. After the filtration of phosphate impurities, the solution is ready for further processing, such as SX. As an unexpected result from the leachate processing, 20–30% of the Ni and Co co-crystalize as the double salt after cooling to room temperature, which could provide a shorter route to their recovery.
The activities described in this (report) are related to the analysis and testing of graphite and mine tailing samples provided by the Recipient for the extraction and recovery of embedded metals. This report focused on recovery of platinum group metals (PGMs), which appear in relatively high abundance, particularly technically important elements ruthenium and rhodium. Work performed involved assessment of materials followed by extraction tests using two methods. A novel electrochemically-driven route was compared to a chemical route for extraction of the metals. The electrochemically driven route showed similar results while producing the lixiviant in the electrochemical cell, hence reducing chemical requirements.