Engineering Papers⌕ Search

Engineering topics

Ren, Yang

Publications and source records attributed to Ren, Yang.

At least 91 records · Page 5

Phase transformation dynamics guided alloy development for additive manufacturing

Fusion-based additive manufacturing technologies enable the fabrication of geometrically and compositionally complex parts unachievable by conventional manufacturing methods. However, the non-uniform and far-from-equilibrium heating/cooling conditions pose a significant challenge to consistently obtaining desirable phases in the as-printed parts. Here, in this study, we report a martensite stainless steel development guided by phase transformation dynamics revealed by in-situ high-speed, high-energy, high-resolution X-ray diffraction. This developed stainless steel consistently forms desired fully martensitic structure across a wide range of cooling rates (10 2 –10 7 °C/s), which enables direct printing of parts with fully martensitic structure. The as-printed material exhibits a yield strength of 1157 ± 23 MPa, comparable to its wrought counterpart after precipitation-hardening heat-treatment. The as-printed property is attributed to the fully martensitic structure and the fine precipitates formed during the intrinsic heat treatment in additive manufacturing. The phase transformation dynamics guided alloy development strategy demonstrated here opens the path for developing reliable, high-performance alloys specific for additive manufacturing.

17–4 PH stainless steel↗

A New Cathode Material for a Li–O 2 Battery Based on Lithium Superoxide

Li–O 2 batteries suffer from large charge overpotentials due to the high charge transfer resistance of Li 2 O 2 discharge products. A potential solution to this problem is the development of LiO 2 -based batteries that possess low charge overpotentials due to the lower charge transfer resistance of LiO 2 . In this report, IrLi nanoparticles were synthesized and implemented for the first time as a LiO 2 battery cathode material. The IrLi nanoparticle synthesis was achieved by a temperature- and time-optimized thermal reaction between a precise ratio of iridium nanoparticles and lithium metal. Li–O 2 batteries employing the IrLi-rGO cathodes were cycled up to 100 cycles at moderate current densities with sustained low cell charge potentials (<3.5 V). Further, various characterization techniques, including SEM, DEMS, TEM, Raman, and titration, were used to demonstrate the LiO 2 discharge product and the absence of Li 2 O 2 . On the basis of first-principles calculations, it was concluded that the formation of crystalline LiO 2 can be stabilized by epitaxial growth on the (111) facets of IrLi nanoparticles present on the cathode surface. These findings demonstrate that, in addition to the previously studied Ir 3 Li intermetallic, the IrLi intermetallic also provides a means by which LiO 2 discharge products can be stabilized and confirms the importance of templating for the formation process.

25 ENERGY STORAGE↗

Constructing O2/O3 homogeneous hybrid stabilizes Li-rich layered cathodes

With the advantages of high energy density and low manufacture cost, lithium-rich layered oxides (LLOs), typically with a layered O3-type structure, are regarded as promising cathodes for lithium-ion batteries (LIBs), but their broad usages are hindered by severe voltage decay over cycling. Although recent progress in O2-type LLOs has aroused interest for their less voltage decay, the critical barrier of unsatisfactory capacity retention has not been overcome yet. In this work, to tackle these handicaps, we design a new type of LLO (O2/O3-type LLO) with a homogeneous hybrid structure, where the O2 and O3 lattice stacking sequences are arranged alternatively. Benefitting from this novel O2/O3 hybrid structure, the designed material shows greatly improved voltage and capacity stability than that of pure O2- and O3-type LLOs. Revealed by in-situ synchrotron X-ray diffraction and operando differential electrochemical mass spectra, the O2/O3-hybrid LLO cathode shows a more reversible structural evolution, smaller volume change and suppressed oxygen loss during the electrochemical processes. Our approach has initiated a new way to reduce the capacity and voltage decay of LLOs, which endows great promise to the development of high-energy-density LIBs.

25 ENERGY STORAGE↗

Repurposing the θ (Al 2 Cu) phase to simultaneously increase the strength and ductility of an additively manufactured Al–Cu alloy

The Al–Cu–Mn–Zr (ACMZ) cast family of alloys offers unique properties and value propositions for higher strength, higher temperature lightweight components of future vehicles. Earlier research has demonstrated trade-offs in the selection of the alloy chemistry in which an increase in Cu content from 6 up to 9 wt% improves hot tear resistance but lowers ductility. However, a recent study has demonstrated that higher-Cu (9Cu) ACMZ fabricated with laser powder bed fusion additive manufacturing (AM) results in an increase in both ductility and strength when compared to as-aged microstructure of cast 9Cu alloys. The mechanisms of differing mechanical performance of the cast and AM ACMZ alloys are elucidated in the current paper through the utilization of in situ high energy x-ray diffraction (HEXRD) tensile testing wherein lattice strains of different phases are calculated and correlated to their stresses. The ACMZ alloys consisted of theta (θ) and theta prime (θ') phases (both Al 2 Cu in nominal composition) within an aluminum matrix. The larger micron-size θ phase which decorated the grain boundaries in 9Cu ACMZ cast alloys recorded small lattice strains, while the submicron, homogeneously distributed θ phase in the 9Cu ACMZ AM alloy recorded considerably higher lattice strains. The maximum stress reached in the θ phase for the cast 9Cu alloy was found to be ~280 MPa, which was lower than the AM 9Cu alloy which registered a maximum stress of ~1.4 GPa. These measurements indicate that delayed fracture of the finer intermetallic phases simultaneously improves the ductility and strength of AM 9Cu alloy relative to the cast 9Cu alloy, which exhibits early fracture of the larger intermetallic particles.

36 MATERIALS SCIENCE↗

Grain‐Boundary‐Rich Noble Metal Nanoparticle Assemblies: Synthesis, Characterization, and Reactivity

Abstract Here, a comprehensive study on the synthesis, characterization, and reactivity of grain‐boundary (GB)‐rich noble metal nanoparticle (NP) assemblies is presented. A facile and scalable synthesis of Pt, Pd, Au, Ag, and Rh NP assemblies is developed, in which NPs are predominantly connected via Σ3 (111) twin GBs, forming a network. Driven by water electrolysis, the random collisions and oriented attachment of colloidal NPs in solution lead to the formation of Σ3 (111) twin boundaries and some highly mismatched GBs. This synthetic method also provides convenient control over the GB density without altering the crystallite size or GB type by varying the NP collision frequency. The structural characterization reveals the presence of localized tensile strain at the GB sites. The ultrahigh activity of GB‐rich Pt NP assembly toward catalytic hydrogen oxidation in air is demonstrated, enabling room‐temperature catalytic hydrogen sensing for the first time. Finally, density functional theory calculations reveal that the strained Σ3(111) twin boundary facilitates oxygen dissociation, drastically enhancing the hydrogen oxidation rate via the dissociative pathway. This reported large‐scale synthesis of the Σ3 (111) twin GB‐rich structures enables the development of a broad range of high‐performance GB‐rich catalysts.

Geng, Xin↗

Effect of the grain arrangements on the thermal stability of polycrystalline nickel-rich lithium-based battery cathodes

One of the most challenging aspects of developing high-energy lithium-based batteries is the structural and (electro)chemical stability of Ni-rich active cathode materials at thermally-abused and prolonged cell cycling conditions. Here, we report in situ physicochemical characterizations to improve the fundamental understanding of the degradation mechanism of charged polycrystalline Ni-rich cathodes at elevated temperatures (e.g., ≥ 40 °C). Using multiple microscopy, scattering, thermal, and electrochemical probes, we decouple the major contributors for the thermal instability from intertwined factors. Our research work demonstrates that the grain microstructures play an essential role in the thermal stability of polycrystalline lithium-based positive battery electrodes. We also show that the oxygen release, a crucial process during battery thermal runaway, can be regulated by engineering grain arrangements. Furthermore, the grain arrangements can also modulate the macroscopic crystallographic transformation pattern and oxygen diffusion length in layered oxide cathode materials.

36 MATERIALS SCIENCE↗

Visualizing the Nanoscale Oxygen and Cation Transport Mechanisms during the Early Stages of Oxidation of Fe–Cr–Ni Alloy Using In Situ Atom Probe Tomography

Abstract Understanding the early stages of interactions between oxygen and material surfaces—especially at very high spatial resolutions—is highly beneficial for fields ranging from materials degradation, corrosion, geological sciences, forensics, and catalysis. The ability of in situ atom probe tomography (APT) is demonstrated to track the diffusion of oxygen and metal ions at nanoscale spatial resolution during the early stages of oxidation of a model Fe–Cr–Ni alloy. Using 18 O isotope tracers in these in situ APT experiments and complementary ex situ multimodal microscopy, spectroscopy, and computational simulations allows to precisely analyze the kinetics of oxidation and determine that outward cation diffusion to oxide/air interface is the primary mechanism for intragranular oxide growth in this alloy at 300 °C. This unique in situ isotopic tracer APT approach and the insights gained can be highly beneficial for studying early stages of gas–surface reactions in a broad array of materials.

36 MATERIALS SCIENCE↗

Origin of structural degradation in Li-rich layered oxide cathode

Li- and Mn-rich (LMR) cathode materials that utilize both cation and anion redox can yield substantial increases in battery energy density 1,2,3 . However, although voltage decay issues cause continuous energy loss and impede commercialization, the prerequisite driving force for this phenomenon remains a mystery 3,4,5,6 In this work, with in situ nanoscale sensitive coherent X-ray diffraction imaging techniques, we reveal that nanostrain and lattice displacement accumulate continuously during operation of the cell. Evidence shows that this effect is the driving force for both structure degradation and oxygen loss, which trigger the well-known rapid voltage decay in LMR cathodes. By carrying out micro- to macro-length characterizations that span atomic structure, the primary particle, multiparticle and electrode levels, we demonstrate that the heterogeneous nature of LMR cathodes inevitably causes pernicious phase displacement/strain, which cannot be eliminated by conventional doping or coating methods. We therefore propose mesostructural design as a strategy to mitigate lattice displacement and inhomogeneous electrochemical/structural evolutions, thereby achieving stable voltage and capacity profiles. These findings highlight the significance of lattice strain/displacement in causing voltage decay and will inspire a wave of efforts to unlock the potential of the broad-scale commercialization of LMR cathode materials.

25 ENERGY STORAGE↗

Highly reversible Zn metal anode enabled by sustainable hydroxyl chemistry

Rechargeable Zn metal batteries (RZMBs) may provide a more sustainable and lower-cost alternative to established battery technologies in meeting energy storage applications of the future. However, the most promising electrolytes for RZMBs are generally aqueous and require high concentrations of salt(s) to bring efficiencies toward commercially viable levels and mitigate water-originated parasitic reactions including hydrogen evolution and corrosion. Electrolytes based on nonaqueous solvents are promising for avoiding these issues, although full cell performance demonstrations with solvents other than water have been very limited. To address these challenges, we investigated MeOH as an alternative electrolyte solvent. These MeOH-based electrolytes exhibited exceptional Zn reversibility over a wide temperature range, with a Coulombic efficiency > 99.5% at 50% Zn utilization without cell short-circuit behavior for > 1,800 h. More important, this remarkable performance translates well to Zn || metal-free organic cathode full cells, supporting < 6% capacity decay after > 800 cycles at –40°C.

25 ENERGY STORAGE↗

Elastic Lattice Enabling Reversible Tetrahedral Li Storage Sites in a High-Capacity Manganese Oxide Cathode

The key to breaking through the capacity limitation imposed by intercalation chemistry lies in the ability to harness more active sites that can reversibly accommodate more ions (e.g., Li + ) and electrons within a finite space. However, excessive Li-ion insertion into the Li layer of layered cathodes results in fast performance decay due to the huge lattice change and irreversible phase transformation. Here, in this study, an ultrahigh reversible capacity is demonstrated by a layered oxide cathode purely based on manganese. Through a wealth of characterizations, it is clarified that the presence of low-content Li 2 MnO 3 domains not only reduces the amount of irreversible O loss; but also regulates Mn migration in LiMnO 2 domains, enabling elastic lattice with high reversibility for tetrahedral sites Li-ion storage in Li layers. This work utilizes bulk cation disorder to create stable Li-ion-storage tetrahedral sites and an elastic lattice for layered materials, with a reversible capacity of 600 mA h g –1 , demonstrated in th range 0.6–4.9 V versus Li/Li + at 10 mA g –1 . Admittedly, discharging to 0.6 V might be too low for practical use, but this exploration is still of great importance as it conceptually demonstrates the limit of Li-ions insertion into layered oxide materials.

25 ENERGY STORAGE↗

Origin and regulation of oxygen redox instability in high-voltage battery cathodes

Oxygen redox at high-voltage has emerged as a transformative paradigm for high-energy battery cathodes such as layered transition-metal oxides by offering extra capacity beyond conventional transition-metal redox. However, these cathodes suffer from voltage hysteresis, voltage fade, and capacity drop upon cycling; single-crystalline cathodes have recently shown some improvements but these challenges still remain. We reveal the fundamental origin of oxygen redox instability to be originated from the domain boundaries that are present in single-crystalline cathode particles. By synthesizing single-crystalline cathodes free of domain boundaries, we show that the elimination of domain boundaries enhances the reversible lattice oxygen redox while inhibiting the irreversible oxygen release. Further, this leads to significantly suppressed structural degradation and improved mechanical integrity during battery cycling and abuse heating. The robust oxygen redox enabled through domain boundary control provides practical opportunities towards high-energy, long-cycling, and safe batteries.

25 ENERGY STORAGE↗

Synchrotron X‐Ray‐Driven Nitrogen Reduction on an AgCu Thin Film

Abstract Nitrogen (N 2 ) is an essential element for life, but kinetically stable N 2 in the atmosphere needs to be reduced to biologically available forms as a nutrient for organisms. Abiotic nitrogen fixation is critical to the origin of life on the early Earth, which is due to lightning or mineral‐based reduction. Here, synchrotron X‐ray‐induced silver nitrate formation on a silver copper (AgCu) thin‐film is reported. Time‐resolved X‐ray diffraction measurements show that under intense X‐ray exposure, initially formed silver oxides (AgOx) are quickly converted to silver nitrate (AgNO 3 ). Interestingly, AgNO 3 is first formed in its high‐temperature phase with a space group of R3cH , which gradually transforms to the room temperature phase with a space group of Pbca under continuous X‐ray irradiation. The result not only provides a new clue about the abiotic nitrogen reduction prior to life but also demonstrates a novel strategy of materials synthesis using synchrotron X‐rays.

Hui, Jian↗

Entropy and crystal-facet modulation of P2-type layered cathodes for long-lasting sodium-based batteries

Abstract P2-type sodium manganese-rich layered oxides are promising cathode candidates for sodium-based batteries because of their appealing cost-effective and capacity features. However, the structural distortion and cationic rearrangement induced by irreversible phase transition and anionic redox reaction at high cell voltage (i.e., >4.0 V) cause sluggish Na-ion kinetics and severe capacity decay. To circumvent these issues, here, we report a strategy to develop P2-type layered cathodes via configurational entropy and ion-diffusion structural tuning. In situ synchrotron X-ray diffraction combined with electrochemical kinetic tests and microstructural characterizations reveal that the entropy-tuned Na 0.62 Mn 0.67 Ni 0.23 Cu 0.05 Mg 0.07 Ti 0.01 O 2 (CuMgTi-571) cathode possesses more {010} active facet, improved structural and thermal stability and faster anionic redox kinetics compared to Na 0.62 Mn 0.67 Ni 0.37 O 2 . When tested in combination with a Na metal anode and a non-aqueous NaClO 4 -based electrolyte solution in coin cell configuration, the CuMgTi-571-based positive electrode enables an 87% capacity retention after 500 cycles at 120 mA g −1 and about 75% capacity retention after 2000 cycles at 1.2 A g −1 .

25 ENERGY STORAGE↗

Synchrotron X-ray-induced Synthesis of Copper Hydroxide Nitrate Nanoplates on Cu Thin Films in an Ambient Atmosphere

Synchrotron X-rays are widely used for material characterizations. However, they can also ionize atoms and molecules to damage and manipulate probed materials. We report here an X-ray-induced growth of copper hydroxide nitrate, Cu 2 (OH) 3 NO 3 , on copper thin films in the ambient atmosphere without solvents and thermal treatment. In situ synchrotron X-ray diffraction measurements showed that the time-dependent growth process of the Cu 2 (OH) 3 NO 3 is accompanied by the consumption of Cu metal and can be described by a sigmoidal model. The growth rate was reduced after the initial fast growth period. Scanning electron microscopy (SEM) images show that the isolated islands of Cu 2 (OH) 3 NO 3 nanoplates formed in the beginning, which grew together with new nanoplates formed under continued X-ray irradiation. The result demonstrated that high-flux synchrotron X-rays may provide an unconventional approach to synthesizing and manipulating materials, which will inspire future investigation both experimentally and theoretically.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗