Engineering Papers⌕ Search

Engineering topics

Ren, Yang

Publications and source records attributed to Ren, Yang.

At least 469 records · Page 26

Fabrication, microstructure and mechanical properties of W-NiTi composites

Here, new two-phase tungsten-based composites containing 88 wt% tungsten powders and 12 wt% nearly equiatomic NiTi alloy deforming by martensite variant detwinning were fabricated by infiltration and hot pressing in this study. The change of Ti/Ni ratio in NiTi mater alloy and the effect of addition of Nb element on the microstructure, martensitic transformation and mechanical properties of W-NiTi composites were investigated by comparison of W-Ni 50 Ti 50 , W-Ni 44 Ti 56 , W-Ni 42 Ti 58 and W-Ni 42 Ti 53 Nb 5 composites. The results showed that brittle Ni 3 Ti formed in the W-Ni 50 Ti 50 and W-Ni 44 Ti 56 composites and brittle Ti 2 Ni formed in the W-Ni 42 Ti 58 composites while no brittle intermetallics formed in the W-Ni 42 Ti 53 Nb 5 composite. The W-Ni 42 Ti 53 Nb 5 composite exhibited the sharpest martensitic transformation with the largest transformation enthalpy among the four different composites. The W-Ni 42 Ti 53 Nb 5 composite exhibited a double-yielding phenomenon under compression with an ultimate compressive strength of 3820 MPa and a deformation of 50.4%. In-situ synchrotron high-energy Xray diffraction measurements revealed the first yielding was caused by the martensite reorientation of the NiTi matrix and the second was due to the commencement of massive plastic deformation of the reoriented martensite and is also attributed to the microscopic internal fracturing of the W particles.

36 MATERIALS SCIENCE↗

Tunable thermal expansion and magnetism in Zr-doped ScF 3

The negative thermal expansion (NTE) behavior provides us an opportunity to design materials with controllable coefficient of thermal expansion (CTE). In this letter, we report a tunable isotropic thermal expansion in the cubic (Sc 1-x Zr x )F 3+δ over a wide temperature and CTE range ($α$ l = -4.0 to+ 16.8 x 10 -6 K -1 , 298–648 K). The thermal expansion can be well adjusted from strong negative to zero, and finally to large positive. Intriguingly, isotropic zero thermal expansion ($α$ l = 2.6 x 10 -7 K -1 , 298–648 K) has been observed in the composition of (Sc 0.8 Zr 0.2 )F 3+δ . The controllable thermal expansion in (Sc 1-x Zr x )F 3+δ is correlated to the local structural distortion. Interestingly, the ordered magnetic behavior has been found in the zero thermal expansion compound of (Sc 0.8 Zr 0.2 )F 3+δ at room temperature, which presumably correlates with the unpaired electron of the lower chemical valence of Zr cation. We conclude the present study provides a useful reference to control the thermal expansion and explore the multi-functionalization for NTE materials.

36 MATERIALS SCIENCE↗

Atomic Linkage Flexibility Tuned Isotropic Negative, Zero, and Positive Thermal Expansion in MZrF 6 (M = Ca, Mn, Fe, Co, Ni, and Zn)

The controllable isotropic thermal expansion with a broad coefficient of thermal expansion (CTE) window is intriguing but remains challenge. Herein we report a cubic MZrF 6 series (M = Ca, Mn, Fe, Co, Ni and Zn), which exhibit controllable thermal expansion over a wide temperature range and with a broader CTE window (–6.69 to +18.23 × 10 –6 /K). In particular, an isotropic zero thermal expansion (ZTE) is achieved in ZnZrF 6 , which is one of the rarely documented hightemperature isotropic ZTE compounds. By utilizing temperature dependent high-energy synchrotron X-ray total scattering diffraction, it is found that the flexibility of metal···F atomic linkages in MZrF 6 plays a critical role in distinct thermal expansions. The flexible metal···F atomic linkages induce negative thermal expansion (NTE) for CaZrF 6 , whereas the stiff ones bring positive thermal expansion (PTE) for 6. Thermal expansion could be transformed from striking negative, to zero, and finally to considerable positive though tuning the flexibility of metal···F atomic linkages by substitution with a series of cations on M sites of MZrF 6 . In conclusion, the present study not only extends the scope of NTE families and rare high-temperature isotropic ZTE compounds but also proposes a new method to design systematically controllable isotropic thermal expansion frameworks from the perspective of atomic linkage flexibility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Anomalous expansion of Nb nanowires in a NiTi matrix under high pressure

Under high pressure, materials usually shrink during compression as described by an equation of state. Here, we present the anomalous volume expansion behavior of a one-dimensional Nb nanowire embedded in a NiTi transforming matrix, while the matrix undergoes a pressure-induced martensitic transformation. The Nb volume expansion depends on the NiTi transition pressure range from the matrix, which is controlled by the shear strain induced by different pressure transmitting media. The transformation-induced interfacial stresses between Nb and NiTi may play a major role in this anomaly. In conclusion, our discovery sheds new light on the nano-interfacial effect on mechanical anomalies in heterogeneous systems during a pressure-induced phase transition.

36 MATERIALS SCIENCE↗

Prospects for spinel-stabilized, high-capacity lithium-ion battery cathodes

Herein we report early results on efforts to optimize the electrochemical performance of a cathode composed of a lithium- and manganese-rich “layered-layered-spinel” material for lithium-ion battery applications. Pre-pilot scale synthesis leads to improved particle properties compared with lab-scale efforts, resulting in high capacities (≳200 mAh/g) and good energy densities (>700 Wh/kg) in tests with lithium-ion cells. Subsequent surface modifications give further improvements in rate capabilities and high-voltage stability. These results bode well for advances in the performance of this class of lithium- and manganese-rich cathode materials.

25 ENERGY STORAGE↗

Novel elastic deformation mechanism in multifunctional Ti–Nb alloy

In-situ high-energy X-ray diffraction was used to reveal a novel elastic deformation mechanism of the polycrystalline Ti-24Nb-4Zr-8Sn alloy under uniaxial compression. These experiments of polycrystal provide direct evidence on anomalous change in full widths at half maximum for {110} β peak during elastic deformation, i.e. peak broadening during unloading and peak narrowing upon loading, which is attributed to the formation of stress-induced irreversible ω phase as clearly demonstrated in single crystal during compression. Difference in modulus between omega and beta phases induces different change in lattice strain causing the broadening and narrowing of diffraction peak near {110} β where actually contains $\{\bar{1120}\}_{\omega}$ under different applied stress. Finally, this study offers new perspectives to investigate intrinsic mechanism on specific phase transformation during elastic deformation.

36 MATERIALS SCIENCE↗

Exploring Pore Formation of Atomic Layer-Deposited Overlayers by in Situ Small- and Wide-Angle X-ray Scattering

In this work, we explore the pore structure of overcoated materials by in situ synchrotron small- and wide-angle X-ray scattering (SAXS)/(WAXS). Thin films of aluminum oxide (Al2O3) and titanium dioxide (TiO2) with thicknesses of 4.9 and 2.5 nm, respectively, are prepared by atomic layer deposition (ALD) on non-porous nanoparticles. In situ X-ray measurements reveal that porosity is induced in the ALD films by annealing the samples at high temperature. Moreover, this pore formation can be attributed to densification resulting from an amorphous to crystalline phase transition of the ALD films as confirmed by high resolution X-ray diffraction (XRD) and pair distribution function (PDF). Simultaneous SAXS/WAXS results not only show that the porosity is formed by this phase transition but also that the pore size increases with temperature.

Li, Tao↗

Shear-Coupled Grain Growth and Texture Development in a Nanocrystalline Ni-Fe Alloy during Cold Rolling

The evolution of texture, grain size, grain shape, dislocation and twin density has been determined by synchrotron X-ray diffraction and line profile analysis in a nanocrystalline Ni- Fe alloy after cold rolling along different directions related to the initial fiber and the long axis of grains. The texture evolution has been simulated by the Taylor-type relaxed constraints viscoplastic polycrystal model. The simulations were based on the activity of partial dislocations in correlation with the experimental results of dislocation density determination. The concept of stress-induced shear-coupling is supported and strengthened by both the texture simulations and the experimentally determined evolution of the microstructure parameters. Grain-growth and texture evolution are shown to proceed by the shear-coupling mechanism supported by dislocation activity as long as the grain size is not smaller than about 20 nm.

Dislocation mechanism of grain growth↗

Giant Polarization and High Temperature Monoclinic Phase in a Lead-Free Perovskite of Bi(Zn 0.5 Ti 0.5 )O 3 -BiFeO 3

Lead-free piezoelectrics have attracted increasing attention due to the awareness of lead toxicity to the environment. Here, a new Bi-based lead-free perovskite of (1-x)Bi(Zn 0.5 Ti 0.5 )O 3 -xBiFeO 3 has been synthesized via high-pressure and high-temperature method. It exhibits interest-ing properties of giant polarization, morphotropic phase boundary (MPB), and monoclinic phase. In particular, large tetragonality ( c/a = 1.228) and giant spontaneous polariza-tion of 110 μC/cm 2 has been obtained in 0.6Bi(Zn 0.5 Ti 0.5 )O 3 -0.4BiFeO 3 , which is much higher than most available lead-free materials and conventional Pb(Zr,Ti)O 3 . MPB is clearly identified to be constituted by tetragonal and monoclinic phases at x = 0.5. Notably, a single monoclinic phase has been observed at x = 0.6, which exhibits an intriguing high temperature property. In conclusion, the present results are helpful to explore new lead-free MPB systems in bismuth-based compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In Operando XRD and TXM Study on the Metastable Structure Change of NaNi 1/3 Fe 1/3 Mn 1/3 O 2 under Electrochemical Sodium-Ion Intercalation

In operando XRD and TXM-XANES approaches demonstrate that structure evolution in NaNi 1/3 Fe 1/3 Mn 1/3 O 2 during cycling follows a continuous change, and the formation of a nonequilibrium solid solution phase in the existence of two phases. Here, an O3' and P3' monoclinic phase occur, and redox couples of Ni 3+ /Ni 4+ and Fe 3+ /Fe 4+ are mainly responsible in the charge voltage range from 4.0 to 4.3 V.

36 MATERIALS SCIENCE↗

Fabrication of ultrafine manganese oxide-decorated carbon nanofibers for high-performance electrochemical capacitors

Ultrafine manganese oxide-decorated carbon nanofibers (MnOn-CNF) as a new type of electrode materials are facilely fabricated by direct conversion of Mn, Zn-trimesic acid (H3BTC) metal organic framework fibers (Mn-ZnBTC). The construction and evolution of Mn-ZnBTC precursors are investigated by SEM and in situ high-energy XRD. The manganese oxides are highly dispersed onto the porous carbon nanofibers formed simultaneously, verified by TEM, X-ray absorption fine structure (XAFS), Raman, ICP-AES and N2 adsorption techniques. As expected, the resulting MnOn-CNF composites are highly stable, and can be cycled up to 5000 times with a high capacitance retention ratio of 98% in electrochemical capacitor measurements. They show a high capacitance of up to 179 F g–1 per mass of the composite electrode, and a remarkable capacitance of up to 18290 F g–1 per active mass of the manganese(IV) oxide, significantly exceeding the theoretical specific capacitance of manganese(IV) oxide (1370 F g–1). The maximum energy density is up to 19.7 Wh kg–1 at the current density of 0.25 A g–1, even orders higher than those of reported electric double-layer capacitors and pseudocapacitors. The excellent capacitive performance can be ascribed to the joint effect of easy accessibility, high porosity, tight contact and superior conductivity integrated in final MnOn-CNF composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Peptide-Directed PdAu Nanoscale Surface Segregation: Toward Controlled Bimetallic Architecture for Catalytic Materials

Bimetallic nanoparticles are of immense scientific and technological interest given the synergistic properties observed when mixing two different metallic species at the nanoscale. This is particularly prevalent in catalysis, where bimetallic nanoparticles often exhibit improved catalytic activity and durability over their monometallic counterparts. Yet despite intense research efforts, little is understood regarding how to optimize bimetallic surface composition and structure synthetically using rational design principles. Recently, it has been demonstrated that peptide-enabled routes for nanoparticle synthesis result in materials with sequence-dependent catalytic properties, providing an opportunity for rational design through sequence manipulation. In this study, bimetallic PdAu nanoparticles are synthesized with a small set of peptides containing known Pd and Au binding motifs. The resulting nanoparticles were extensively characterized using high-resolution scanning transmission electron microscopy, X-ray absorption spectroscopy and high-energy X-ray diffraction coupled to atomic pair distribution function analysis. Structural information obtained from synchrotron radiation methods were then used to generate model nanoparticle configurations using reverse Monte Carlo simulations, which illustrate sequence-dependence in both surface structure and surface composition. Replica exchange solute tempering molecular dynamic simulations were also used to predict the modes of peptide binding on monometallic surfaces, indicating that different sequences bind to the metal interfaces via different mechanisms. As a testbed reaction, electrocatalytic methanol oxidation experiments were performed, wherein differences in catalytic activity are clearly observed in materials with identical bimetallic composition. Finally, taken together, this study indicates that peptides could be used to arrive at bimetallic surfaces with enhanced catalytic properties, which could be leveraged for rational bimetallic nanoparticle design using peptide-enabled approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synchrotron high energy X-ray diffraction study of microstructure evolution of severely cold drawn NiTi wire during annealing

Microstructure evolution of a cold-drawn NiTi shape memory alloy wire was investigated by means of in-situ synchrotron high-energy X-ray diffraction during continuous heating. The cold-drawn wire contained amorphous regions and nano-crystalline domains in its microstructure. Pair distribution function analysis revealed that the amorphous regions underwent structural relaxation via atomic rearrangement when heated above 100 °C. The nano-crystalline domains were found to exhibit a strong cold work induced lattice strain anisotropy having a preferential <111> fiber orientation along the wire axial direction. The lattice strain anisotropy systematically decreased upon heating above 200 °C, implying a structural recovery. A broad conical texture was formed in the wire specimen after crystallization similar in detail to the initial <111> texture axial orientation of the nano-crystalline domains produced by the severe cold wire drawing deformation.

crystallization↗

A new strategy to mitigate the initial capacity loss of lithium ion batteries

Hard carbon (non-graphitizable) and related materials, like tin, tin oxide, silicon, and silicon oxide, have a high theoretical lithium delivery capacity (>550 mAh/g depending on their structural and chemical properties) but unfortunately they also exhibit a large initial capacity loss (ICL) that overrides the true reversible capacity in a full cell. Overcoming the large ICL of hard carbon in a full-cell lithium-ion battery (LIB) necessitates a new strategy wherein a sacrificial lithium source additive, such as, Li5FeO4 (LFO), is inserted on the cathode side. Full batteries using hard carbon coupled with LFO-LiCoO2 (LCO) are currently under development at our laboratory. We find that the reversible capacity of a cathode containing LFO can be increased by 14%. Furthermore, the cycle performance of full cells with LFO additive is improved from <90% to >95%. We show that the LFO additive not only can address the irreversible capacity loss of the anode, but can also provide the additional lithium ion source required to mitigate the lithium loss caused by side reactions. In addition, we have explored the possibility to achieve higher capacity with hard carbon, whereby the energy density of full cells can be increased from ca. 300 Wh/kg to >400 Wh/kg.

hard carbon↗

The Distortion‐Adjusted Change of Thermal Expansion Behavior of Cubic Magnetic Semiconductor (Sc 1− x M x )F 3 (M = Al, Fe)

For the study of negative thermal expansion (NTE) compounds, it is critical to effectively control the thermal expansion. In this letter, a chemical approach has been taken to control the thermal expansion behavior in ScF 3 which has a strong NTE. Owing to the difference of radius of substituting ions, local distortion inevitably emerges in the lattice matrix, which is verified by pair distribution function analysis of high‐resolution synchrotron X‐ray scattering. It is a valuable clue that the thermal expansion behaviors in the ScF 3 based systems and other trifluorides are correlated closely to structural distortion of metal‐F‐metal linkages. In addition, the introduction of 3 d transition‐metal enables its semiconductor and ferromagnetic characteristics. This study provides important reference opinion for the control of thermal expansion and introduction of multifunctionalization for those NTE compounds with open framework structure.

Han, Fei↗