Engineering Papers⌕ Search

Engineering topics

Ren, Y.

Publications and source records attributed to Ren, Y..

At least 73 records · Page 4

Crystal plasticity based constitutive modeling of ZEK100 magnesium alloy combined with in-situ HEXRD experiments

In the current works, both micro- and macro-mechanical properties of a hexagonal close-packed (HCP) polycrystalline ZEK100 magnesium alloy were investigated. In the experimental perspective, in-situ high energy X-ray diffraction (HEXRD) from a synchrotron source was conducted during the uniaxial tension along the rolling direction (RD) and the transverse direction (TD) to measure the lattice strain evolutions and stress-strain behaviors. In the modeling perspective, crystal plasticity finite element (CPFE) model was developed incorporating the deformation twinning for the HCP-structured metals. The HEXRD experiments and crystal plasticity models were then coupled to characterize the constitutive behaviors of the ZEK100 alloy. The lattice strain data representing the microscopic behavior of the material and the macroscopic stress-strain behavior were then tied together as objective values to estimate the critical resolved shear stress (CRSS) and hardening parameters of available slip and twin systems of the ZEK100 alloy using the developed CPFE model. The stress-strain behavior as well as the lattice strain variation during the uniaxial tension tests are presented using the CPFE model and compared with the actual HEXRD data.

36 MATERIALS SCIENCE↗

Suppression of crystallization in a Ca-based bulk metallic glass by compression

We have researched the crystallization kinetics of Ca 40 Mg 25 Cu 35 bulk metallic glass under isothermal annealing in the supercooled liquid region, with and without applied stress, by in situ high-energy synchrotron x-ray diffraction. We observed that without stress, crystallization started from the very beginning of isothermal annealing. Yet, when a uniaxial compressive stress was applied during isothermal annealing, no change in atomic order was observed at the beginning. Thereafter, the glassy structure relaxed, but still without noticeable evidence of crystallization. It is proposed that the applied compressive stress restricted the atomic mobility, which suppressed crystallization.

36 MATERIALS SCIENCE↗

In situ synchrotron X-ray diffraction investigations of the physical mechanism of ultra-low strain hardening in Ti-30Zr-10Nb alloy

A warm-rolled, metastable beta-type Ti-30Zr-10Nb alloy exhibited a peculiar two-stage yielding behavior under uniaxial tensile loading, showing a first plastic stage with obvious strain hardening at 0.4%-10.4% strain and a second plastic stage with ultra-low strain hardening at 10.4%-23.5% strain. In situ high-energy X-ray diffraction (HE-XRD) was used to reveal the stress-induced martensitic transformation scenarios and physical mechanism of the different strain hardening rates. It was found that the deformation-induced phase transformation dominated the onset of the first plastic stage corresponding to the selection of favorable martensitic variants, and their elastic interaction contributed to the obvious strain hardening. HE-XRD experiments further verified that the ultra-low strain hardening rate in the second plastic stage was related to an interesting superelasticity of the martensite, which was characterized by the reversible, stress-induced reorientation of the martensite variants. This reorientation of the martensite variants was primarily due to the rigid lattice rotation of similar to 23 degrees about the [110](α '') axis toward the tensile direction. Here, our investigations provide in-depth understanding of the mechanism of the excellent plasticity with ultra-low strain hardening in beta-type titanium alloys.

36 MATERIALS SCIENCE↗

Room-Temperature Deformation and Martensitic Transformation of Two Co-Cr-Based Alloys

Here, deformation of two Co-Cr alloys was studied by in situ synchrotron X-ray diffraction. Both alloys show stress-induced martensite transformation, which is affected by phase stabilities and transformation strains. Crystal structure of WC in Co-20Cr-15W-10Ni is identified. Compared with other phases present, it is elastically isotropic, exhibits high strength, and can elastically withstand strains exceeding 1 pct. Texture change during phase transformation is explained based on the crystal orientation relationship between γ- and ε-phases.

36 MATERIALS SCIENCE↗

Intergranular stress study of TC11 titanium alloy after laser shock peening by synchrotron-based high-energy X-ray diffraction

The distribution of residual lattice strain as a function of depth were carefully investigated by synchrotron-based high energy X-ray diffraction (HEXRD) in TC11 titanium alloy after laser shock peening (LSP). The results presented big compressive residual lattice strains at surface and subsurface, then tensile residual lattice strains in deeper region, and finally close to zero lattice strains in further deep interior with no plastic deformation thereafter. These evolutions in residual lattice strains were attributed to the balance of direct load effect from laser shock wave and the derivative restriction force effect from surrounding material. Significant intergranular stress was evidenced in the processed sample. The intergranular stress exhibited the largest value at surface, and rapidly decreased with depth increase. The magnitude of intergranular stress was proportional to the severity of the plastic deformation caused by LSP. Two shocks generated larger intergranular stress than one shock.

36 MATERIALS SCIENCE↗

Liquid crystal polymer substrate MMIC receiver modules for the ECE Imaging system on the DIII-D

A new generation of millimeter-wave heterodyne imaging receiver arrays has been developed and demonstrated on the DIII-D ECEI system. Improved circuit integration, allowing for absolute calibration, improved noise performance, and shielding from out-of-band emission, is made possible by using advanced liquid crystal polymer (LCP) substrates and MMIC (Monolithic Microwave Integrated Circuit) receiver chips. This array exhibits ~ 15 dB additional gain and > 30x reduction in noise temperature compared to the previous generation and provide ECEI capability for absolute 2-D electron temperature profile measurements. Each LCP horn-waveguide module houses a 3x3 mm GaAs MMIC receiver chip, which consists of a low noise amplifier (LNA), balanced mixer, local oscillator multiplier chain driven by ~12 GHz input via an RF cable to the enclosure box, and IF amplifier. A proof-of-principle instrument with 5 poloidal channels was installed on DIII-D in 2017. The full proof-of-principle system installation (20 poloidal x 8 radial channels) was commissioned early in 2018. The LCP ECEI system is used for pedestal region measurements, especially focusing on temperature evolution during ELM bursting. The DIII-D ECE Imaging signal has been significantly improved with extremely effective shielding of out-of-band microwave noise which plagued previous ECE Imaging studies on DIII-D. In H-mode ELM bursting, the radial propagation of electron heat flow has been detected on DIII-D. The LCP ECE Imaging is expected to be a valuable diagnostic tool for ELM physics investigations.

Zhu, Y.↗

Simultaneously achieved large reversible elastocaloric and magnetocaloric effects and their coupling in a magnetic shape memory alloy

Large reversible caloric effects covering a broad temperature region are essential for high-efficiency and environment-friendly solid-state caloric refrigeration that can potentially replace the traditional vaporcompression-based cooling technology. Here, we report the simultaneously achieved large reversible magnetocaloric and elastocaloric effects in a Ni 43 Co 6 Mn 40 Sn 11 magnetic shape memory alloy. A reversible near-room-temperature magnetic entropy change Δ S m of as high as 19.3 J kg –1 K –1 under 5 T was experimentally obtained and the corresponding adiabatic temperature change Δ T ad was estimated to be 7.7 K. Meanwhile, a large reversible elastocaloric effect with a directly measured Δ T ad up to 7.1 K was attained. The elastocaloric effect exhibits high cyclic stability with no apparent degradation during 380 cycles of loading and unloading. Furthermore, we propose and demonstrate the utilization of the multicaloric approach under the coupled uniaxial stress and magnetic field to enlarge the refrigeration temperature region of reversible caloric effects. By combining the reversible magnetocaloric and elastocaloric effects and the reversible multicaloric effect under the coupling of uniaxial stress and magnetic field in the hysteresis region, large reversible caloric effects covering a broad temperature region from 257 K to 383 K can be obtained. Finally, this study may pave the way for designing advanced caloric materials with cyclically stable and reversible large caloric effects and wide refrigeration temperature region for solid-state refrigeration.

36 MATERIALS SCIENCE↗

Low-field-actuated giant magnetocaloric effect and excellent mechanical properties in a NiMn-based multiferroic alloy

Multiferroic magnetic shape memory alloys with first-order magntostructural transformation exhibit much enhanced magnetocaloric effect which incorporates the latent heat associated with the phase transformation itself, but they suffer from the drawbacks of large hysteresis and transformation interval and consequently too high critical field to actuate the magnetocaloric effect, greatly impeding their applications. Here, by generating a kind of specific stacking-mediated structure of martensite through minor Al substitution to improve the geometric compatibility between martensite and austenite in the Ni 40 Co 10 Mn 40 Sn 9 Al 1 alloy, we greatly reduced the thermal hysteresis and transformation temperature interval while conserving the large magnetization difference between the two phases. Consequently, a low-field-actuated giant magnetocaloric effect with isothermal entropy change of 23 J kg –1 K –1 for a field change from 0 to 2 T, which is among the highest values reported heretofore for all magnetocaloric materials, was successfully achieved. Meanwhile, with minor Al substitution, the present single-phase multiferroic alloy that is intermetallic in nature exhibits superior mechanical properties, including excellent compressive properties over a wide temperature range and a relatively high fracture toughness, which are quite beneficial for practical applications. Lastly, by incorporating the advantages of low cost, environment friendliness and easy fabrication, this alloy shows great potential for magnetocaloric applications.

36 MATERIALS SCIENCE↗

The in-depth residual strain heterogeneities due to an indentation and a laser shock peening for Ti-6Al-4V titanium alloy

In this paper, heterogeneity of the through-thickness residual strain due to the laser shock peening (LSP) in comparison with that due to the indentation was studied in Ti-6Al-4V alloy samples. The latter is almost a quasi-static process while the former features extremely high strain-rate deformation. The synchrotron based high-energy X-ray diffraction was employed to investigate the through-thickness residual strain distribution. The studied two samples after the two processing procedures share the following features: (i) the pressure affected depths are both ~2 mm and (ii) the largest magnitudes of the compressive residual strains parallel to the surface are ~4,000 με. However, the pit depth for the indentation sample is ~9 times larger than that for the LSP. The position featuring the largest magnitude of the compressive residual strain is in the sub-surface for the indentation while it is in the surface for the LSP. Results of the elastic-visco-plastic finite element simulation for the indentation indicate that the position featuring the maximum accumulative plastic shear as defined in this paper corresponds to the location with the largest magnitude of compressive residual strain. To validate this finding, full width at half maximum (FWHM) of the X-ray diffraction profile, which is proportional to the level of the plastic deformation, is also studied. Finally, it is found that positions with the largest FWHM indeed correspond to the largest magnitude of compressive residual strain for both tests.

36 MATERIALS SCIENCE↗

Structural responses of metallic glasses under neutron irradiation

Seeking nuclear materials that possess a high resistance to particle irradiation damage is a long-standing issue. Permanent defects, induced by irradiation, are primary structural changes, the accumulation of which will lead to structural damage and performance degradation in crystalline materials served in nuclear plants. In this work, structural responses of neutron irradiation in metallic glasses (MGs) have been investigated by making a series of experimental measurements, coupled with simulations in ZrCu amorphous alloys. It is found that, compared with crystalline alloys, MGs have some specific structural responses to neutron irradiation. Although neutron irradiation can induce transient vacancy-like defects in MGs, they are fully annihilated after structural relaxation by rearrangement of free volumes. In addition, the rearrangement of free volumes depends strongly on constituent elements. In particular, the change in free volumes occurs around the Zr atoms, rather than the Cu centers. This implies that there is a feasible strategy for identifying glassy materials with high structural stability against neutron irradiation by tailoring the microstructures, the systems, or the compositions in alloys. Furthermore, this work will shed light on the development of materials with high irradiation resistance.

36 MATERIALS SCIENCE↗

Grain size induced monoclinic ( Cm ) to rhombohedral ( R3c ) transformation in sodium potassium bismuth titanate ceramics

Here, grain size effect on structure, remnant polarization and piezoelectric constant of lead-free Na 0.4 K 0.1 Bi 0.5 TiO 3 ceramics with grain sizes of 0.58, 0.85, 1.19 and 1.83 pm was investigated. Synchrotron X-ray diffraction in combination with Rietveld refinement was used to examine the structural changes. We have reported an existence of monoclinic ( Cm ) phase at room temperature and discussed the grain size (1.83 → 0.58 μ m) induced structural transformation ( Cm → R3c ) through both intrinsic polarization rotation and adaptive phase theory. Polarization vector in the (11¯0) pc monoclinic plane rotates towards [111] pc with the reduction of grain size. Better domain alignment and large polar variants results enhanced remnant polarization and piezoelectric constant in 1.83 μ m sample.

36 MATERIALS SCIENCE↗

Overview of NSTX Upgrade initial results and modelling highlights

The National Spherical Torus Experiment (NSTX) has undergone a major upgrade, and the NSTX Upgrade (NSTX-U) Project was completed in the summer of 2015. NSTX-U first plasma was subsequently achieved, diagnostic and control systems have been commissioned, the H-mode accessed, magnetic error fields identified and mitigated, and the first physics research campaign carried out. During ten run weeks of operation, NSTX-U surpassed NSTX record pulse-durations and toroidal fields (TF), and high-performance ~1 MA H-mode plasmas comparable to the best of NSTX have been sustained near and slightly above the n = 1 no-wall stability limit and with H-mode confinement multiplier H 98y,2 above 1. Transport and turbulence studies in L-mode plasmas have identified the coexistence of at least two ion-gyro-scale turbulent micro-instabilities near the same radial location but propagating in opposite (i.e. ion and electron diamagnetic) directions. These modes have the characteristics of ion-temperature gradient and micro-tearing modes, respectively, and the role of these modes in contributing to thermal transport is under active investigation. The new second more tangential neutral beam injection was observed to significantly modify the stability of two types of Alfven eigenmodes. Improvements in offline disruption forecasting were made in the areas of identification of rotating MHD modes and other macroscopic instabilities using the disruption event characterization and forecasting code. Finally, the materials analysis and particle probe was utilized on NSTX-U for the first time and enabled assessments of the correlation between boronized wall conditions and plasma performance. These and other highlights from the first run campaign of NSTX-U are described.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Emergent Low-Symmetry Phases and Large Property Enhancements in Ferroelectric KNbO 3 Bulk Crystals [Emergent Low-Symmetry Phases with Large Property Enhancement in Ferroelectric KNbO 3 Bulk Crystals]

The design of new or enhanced functionality in materials is traditionally viewed as requiring the discovery of new chemical compositions through synthesis. Large property enhancements may however also be hidden within already well-known materials, when their structural symmetry is deviated from equilibrium through a small local strain or field. Here, the discovery of enhanced material properties associated with a new metastable phase of monoclinic symmetry within bulk KNbO 3 is reported. This phase is found to coexist with the nominal orthorhombic phase at room temperature, and is both induced by and stabilized with local strains generated by a network of ferroelectric domain walls. While the local microstructural shear strain involved is only ≈0.017%, the concurrent symmetry reduction results in an optical second harmonic generation response that is over 550% higher at room temperature. Moreover, the meandering walls of the low-symmetry domains also exhibit enhanced electrical conductivity on the order of 1 S m -1 . In conclusion, this discovery reveals a potential new route to local engineering of significant property enhancements and conductivity through symmetry lowering in ferroelectric crystals.

36 MATERIALS SCIENCE↗

Thermal and magnetic hysteresis associated with martensitic and magnetic phase transformations in Ni 52 Mn 25 In 16 Co 7 Heusler alloy

Ni-Mn-In-Co Heusler alloys demonstrate promising magnetocaloric performance for use as refrigerants in magnetic cooling systems with the goal of replacing the lower efficiency, eco-adverse fluid-compression technology. The largest change in entropy occurs when the applied magnetic field causes a merged structural and magnetic transformation and the associated entropy changes of the two transformations works constructively. In this study, magnetic and crystalline phase transformations were each treated separately and the effects of the application of magnetic field on thermal hystereses associated with both structural and magnetic transformations of the Ni 52 Mn 25 In 16 Co 7 were studied. From the analysis of synchrotron diffraction data and thermomagnetic measurements, it was revealed that the alloy undergoes both structural (from cubic austenite to a mixture of 7M & 5M modulated martensite) and magnetic (ferromagnetic to a low-magnetization phase) phase transformations. Here, thermal hysteresis is associated with both transformations, and the variation of the thermal hystereses of the magnetic and structural transformations with applied magnetic field is significantly different. Because of the differences between the hystereses loops of the two transformations, they merge only upon heating under a certain magnetic field.

36 MATERIALS SCIENCE↗

Giant and reversible room-temperature magnetocaloric effect in Ti-doped Ni-Co-Mn-Sn magnetic shape memory alloys

The practical applications of magnetocaloric materials for magnetic refrigeration require not only large magnitude but also reversibility, as well as room-temperature operating temperature, of the magneto caloric effect. However, it is a complex problem to simultaneously meet these demands in the Heusler-type Ni-(Co)-Mn-X (X = In, Sn, Sb, Ga) magnetic shape memory alloys which are a promising candidate for magnetocaloric materials, owing to the interdependence of magnetostructural transformation parameters. In this work, through synergic tuning of magnetostructural transformation parameters via alloying with Ti in Ni 42-x Ti x Co 9 Mn 39 Sn 10 alloys, we achieved a large reversible room-temperature magnetocaloric effect. By alloying with a proper amount of Ti, the martensitic transformation temperature was brought down to room temperature and the sensitivity of transformation temperature to magnetic field change was greatly enhanced with the transformation entropy change still remaining a large value, while the thermal hysteresis and the transformation interval only slightly increased. Thus, the field required to induce the complete and reversible transformation was significantly reduced. As a result, a large reversible room-temperature magnetic entropy change ΔS m of 18.7 J kg -1 K -1 under 5 T was achieved in the Ni 41 Ti 1 Co 9 Mn 39 Sn 10 alloy. This is the first report on reversibleΔS m in Ni-Mn-Sn-based Heusler alloys and the ΔS m we achieved represents the highest reversible ΔS m under 5 T reported heretofore in Ni-Mn-based Heusler alloys. Furthermore, the Ni 41 Ti 1 Co 9 Mn 39 Sn 10 alloy shows good compressive properties and stable martensitic transformation during thermal cycling, beneficial for potential magnetocaloric applications. This study is instructive for the development of high-performance magnetocaloric materials for room-temperature magnetic refrigeration.

36 MATERIALS SCIENCE↗

Individual phase constitutive properties of a TRIP-assisted QP980 steel from a combined synchrotron X-ray diffraction and crystal plasticity approach

Microstructure-based constitutive models for multiphase steels require accurate constitutive properties of the individual phases for component forming and performance simulations. We address this requirement with a combined experimental/theoretical methodology which determines the critical resolved shear stresses and hardening parameters of the constituent phases in QP980, a TRIP assisted steel subject to a two-step quenching and partitioning heat treatment. High energy X-Ray diffraction (HEXRD) from a synchrotron source provided the average lattice strains of the ferrite, martensite, and austenite phases from the measured volume during in situ tensile deformation. The HEXRD data was then input to a computationally efficient, elastic-plastic self-consistent (EPSC) crystal plasticity model which estimated the constitutive parameters of different slip systems for the three phases via a trial-and-error approach. The EPSC-estimated parameters are then input to a finite element crystal plasticity (CPFE) model representing the QP980 tensile sample. The predicted lattice strains and global stress versus strain curves are found to be 8% lower that the EPSC model predicted values and from the HEXRD measurements, respectively. This discrepancy, which is attributed to the stiff secant assumption in the EPSC formulation, is resolved with a second step in which CPFE is used to iteratively refine the EPSC-estimated parameters. Remarkably close agreement is obtained between the theoretically-predicted and experimentally derived flow curve for the QP980 material.

Hu, X. H. (ORCID:0000000277355091)↗

Liquid-to-liquid crossover in the GaIn eutectic alloy

Liquid-liquid crossover is promising and closely related to the atomic dynamics during heating and cooling processes. Here we reveal a reversible structural crossover in the liquid Ga85.8In14.2 eutectic alloys by using in situ synchrotron x-ray diffraction and ab initio molecular dynamics simulation. A kink always appears on the temperature dependent behaviors of density, ratio of the second peak position to the first in the pair correlation function, coordination number, heat capacity, free energy, and atomic diffusivity in the temperature range of about 400–550 K. It is likely ascribed to atomic rearrangements of Ga and In atoms from a relative random packing at high temperatures to a relative nonuniform packing at low temperatures, in which In atoms prefer to have more In neighbors. This observation will promote more understanding of the liquid structure of eutectic alloys

Yu, Q.↗