Engineering topics
Publications and source records attributed to Rejhon, Martin.
The phase-transition of atomically thin graphene coating into a diamond phase increases the hardness and the fracture toughness of SiC even for indentation depths of 10 μm compared to bare SiC, which is against the general indirect relation.
Abstract As the field of low‐dimensional materials (1D or 2D) grows and more complex and intriguing structures are continuing to be found, there is an emerging need for techniques to characterize the nanoscale mechanical properties of all kinds of 1D/2D materials, in particular in their most practical state: sitting on an underlying substrate. While traditional nanoindentation techniques cannot accurately determine the transverse Young's modulus at the necessary scale without large indentations depths and effects to and from the substrate, herein an atomic‐force‐microscopy‐based modulated nanomechanical measurement technique with Angstrom‐level resolution (MoNI/ÅI) is presented. This technique enables non‐destructive measurements of the out‐of‐plane elasticity of ultra‐thin materials with resolution sufficient to eliminate any contributions from the substrate. This method is used to elucidate the multi‐layer stiffness dependence of graphene deposited via chemical vapor deposition and discover a peak transverse modulus in two‐layer graphene. While MoNI/ÅI has been used toward great findings in the recent past, here all aspects of the implementation of the technique as well as the unique challenges in performing measurements at such small resolutions are encompassed.
Silicon carbide (SiC) is one of the hardest known materials. Its exceptional mechanical properties combined with its high thermal conductivity make it a very attractive material for a variety of technological applications. Recently, it was discovered that two-layer epitaxial graphene films on SiC can undergo a pressure activated phase transition into a sp3 diamene structure at room temperature. Here, we show that epitaxial graphene films grown on SiC can increase the hardness of SiC up to 100% at low loads (up to 900 µN), and up to 30% at high loads (10 mN). By using a Berkovich diamond indenter and nanoindentation experiments, we demonstrate that the 30% increase in hardness is present even for indentations depths of 175 nm, almost three hundred times larger than the graphene film thickness. The experiments also show that the yield point of SiC increases up to 77% when the SiC surface is coated with epitaxial graphene. These improved mechanical properties are explained with the formation of diamene under the indenter’s pressure.
Reproducing in vitro the complex multiscale physical features of human tissues creates novel biomedical opportunities and fundamental understanding of cell–environment interfaces and interactions. While stiffness has been recognized as a key driver of cell behavior, systematic studies on the role of stiffness have been limited to values in the KPa–MPa range, significantly below the stiffness of bone. Here, in this work, a platform enabling the tuning of the stiffness of a biocompatible polymeric interface up to values characteristic of human bone is reported, which are in the GPa range, by using extremely thin polymer films on glass and cross-linking the films using ultraviolet (UV) light irradiation. It is shown that a higher stiffness is related to better adhesion, proliferation, and osteogenic differentiation, and that it is possible to switch on/off cell attachment and growth by solely tuning the stiffness of the interface, without any surface chemistry or topography modification. Since the stiffness is tuned directly by UV irradiation, this platform is ideal for rapid and simple fabrication of stiffness patterns and gradients, thus representing an innovative tool for combinatorial studies of the synergistic effect of tissue environmental cues on cell behavior, and creates new opportunities for next-generation biosensors, single-cell patterning, and lab-on-a-chip devices.
Understanding the interfacial properties between an atomic layer and its substrate is of key interest at both the fundamental and technological levels. From Fermi level pinning to strain engineering and superlubricity, the interaction between a single atomic layer and its substrate governs electronic, mechanical and chemical properties. Here, we measure the hardly accessible interfacial transverse shear modulus of an atomic layer on a substrate. By performing measurements on bulk graphite, and on epitaxial graphene films on SiC with different stacking orders and twisting, as well as in the presence of intercalated hydrogen, we find that the interfacial transverse shear modulus is critically controlled by the stacking order and the atomic layer–substrate interaction. Importantly, we demonstrate that this modulus is a pivotal measurable property to control and predict sliding friction in supported two-dimensional materials. The experiments demonstrate a reciprocal relationship between friction force per unit contact area and interfacial shear modulus. As a result, the same relationship emerges from simulations with simple friction models, where the atomic layer– substrate interaction controls the shear stiffness and therefore the resulting friction dissipation.