Reehorst, Andrew L. — Page 2 | Engineering Papers

NASA NTRS1999

National Transportation Safety Board Aircraft Accident Investigation Supported

The main purpose of this investigation was for NASA to help the National Transportation Safety Board (NTSB) gain better understanding of the events that led to the loss of Comair Flight 3272 over Monroe, Michigan, on January 9, 1997. In-flight icing was suspected as being the primary cause of this accident. Of particular interest to the Safety Board was what NASA could learn about the potential performance degradation of the wing of the Embraer EMB-120 twin-turboprop commuter aircraft with various levels of ice contamination. NASA agreed to undertake (1) ice-accretion prediction computations with NASA s LEWICE program to bound the kind of contaminations that the vehicle may have developed, (2) testing in the NASA Lewis Research Center's Icing Research Tunnel to verify and refine the ice shapes developed by LEWICE, (3) a two-dimensional Navier- Stokes analysis to determine the performance degradation that those ice shapes could have caused, and (4) an examination using three-dimensional Navier-Stokes codes to study the three-dimensional effects of ice contamination.

Reehorst, Andrew L.↗

NASA NTRS1994

Close-up analysis of inflight ice accretion

The objective of this effort was to validate in flight, data that has been gathered in the NASA Lewis Research Center's Icing Research Tunnel (IRT) over the past several years. All data was acquired in flight on the NASA Lewis Research Center's Twin Otter Icing Research Aircraft. A faired 3.5 in. diameter metal-clad cylinder exposed to the natural icing environment was observed by a close-up video camera. The grazing angle video footage was recorded to S-VHS video tape and after the icing encounter, the resultant ice shape was documented by 35 mm photography and pencil tracings. The feather growth area was of primary interest; however, all regions of the ice accretion, from the stagnation line to the aft edge of run back were observed and recorded. After analysis of the recorded data several interesting points became evident: (1) the measured flight feather growth rate is consistent with IRT values, (2) the feather growth rate appears to be influenced by droplet size, (3) the feathers were straighter in the lower, spottier LWC of flight in comparison to those observed in the IRT, (4) feather shedding and ice sublimation may be significant to the final ice shape, and (5) the snow encountered on these flights appeared to have little influence on ice growth.

Reehorst, Andrew L.↗

NASA NTRS1992

Prediction of ice accretion on a swept NACA 0012 airfoil and comparisons to flight test results

In the winter of 1989-90, an icing research flight project was conducted to obtain swept wing ice accretion data. Utilizing the NASA Lewis Research Center's DHC-6 DeHavilland Twin Otter aircraft, research flights were made into known icing conditions in Northeastern Ohio. The icing cloud environment and aircraft flight data were measured and recorded by an onboard data acquisition system. Upon entry into the icing environment, a 24 inch span, 15 inch chord NACA 0012 airfoil was extended from the aircraft and set to the desired sweep angle. After the growth of a well defined ice shape, the airfoil was retracted into the aircraft cabin for ice shape documentation. The ice accretions were recorded by ice tracings and photographs. Ice accretions were mostly of the glaze type and exhibited scalloping. The ice was accreted at sweep angles of 0, 30, and 45 degrees. A 3-D ice accretion prediction code was used to predict ice profiles for five selected flight test runs, which include sweep angle of zero, 30, and 45 degrees. The code's roughness input parameter was adjusted for best agreement. A simple procedure was added to the code to account for 3-D ice scalloping effects. The predicted ice profiles are compared to their respective flight test counterparts. This is the first attempt to predict ice profiles on swept wings with significant scalloped ice formations.

Reehorst, Andrew L.↗

NASA NTRS1992

Prediction of ice accretion on a swept NACA 0012 airfoil and comparisons to flight test results

In the winter of 1989-90, an icing research flight project was conducted to obtain swept wing ice accretion data. Utilizing the NASA Lewis Research Center's DHC-6 DeHavilland Twin Otter aircraft, research flights were made into known icing conditions in Northeastern Ohio. The icing cloud environment and aircraft flight data were measured and recorded by an onboard data acquisition system. Upon entry into the icing environment, a 24 inch span, 15 inch chord NACA 0012 airfoil was extended from the aircraft and set to the desired sweep angle. After the growth of a well defined ice shape, the airfoil was retracted into the aircraft cabin for ice shape documentation. The ice accretions were recorded by ice tracings and photographs. Ice accretions were mostly of the glaze type and exhibited scalloping. The ice was accreted at sweep angles of 0, 30, and 45 degrees. A 3-D ice accretion prediction code was used to predict ice profiles for five selected flight test runs, which include sweep angle of zero, 30, and 45 degrees. The code's roughness input parameter was adjusted for best agreement. A simple procedure was added to the code to account for 3-D ice scalloping effects. The predicted ice profiles are compared to their respective flight test counterparts. This is the first attempt to predict ice profiles on swept wings with significant scalloped ice formations.

Reehorst, Andrew L.↗

NASA NTRS1988

An overview of the current NASA program on aircraft icing research

The NASA Lewis Research Center is presently conducting an aircraft icing research program, the major thrust of which is to advance technologies that improve our ability to model the icing phenomenon and its effect on aircraft. The approach employs three interrelated elements: analysis; wind tunnel experiments; and, considerable flight testing in natural icing clouds. This paper presents a brief overview of this program with emphasis on recent accomplishments.

Ranaudo, Richard J.↗

NASA NTRS1987

New methods and materials for molding and casting ice formations

This study was designed to find improved materials and techniques for molding and casting natural or simulated ice shapes that could replace the wax and plaster method. By utilizing modern molding and casting materials and techniques, a new methodology was developed that provides excellent reproduction, low-temperature capability, and reasonable turnaround time. The resulting casts are accurate and tough.

Reehorst, Andrew L.↗