Engineering topics
Publications and source records attributed to Reddy, Pramod.
Substituents can strongly affect electric and thermoelectric properties of molecular junctions (MJs) by tuning quantum interference (QI) in MJs.
Not Available
The primary aim of this research was to develop GaN-based Junction Barrier Schottky (JBS) diodes using an innovative ion implantation process previously established in ARPA-E funded projects. The central focus of our proposed technology revolves around selective area p-type doping, accomplished through the implantation of Mg ions. This approach builds upon our successes in the ARPA-E PNDIODES program, advancing towards commercial device integration. Selective area p-doping plays a pivotal role in realizing the next generation of GaN-based power devices, capable of significantly reducing the carbon footprint in the United States by several million tons. While ion implantation is a well-established technique for achieving selective area doping in SiC and Si materials, its feasibility in GaN had not been demonstrated until now. To fabricate high voltage GaN JBS diodes, we initially created thick n-type drift layers with high carrier concentrations ranging from 5×1015 cm-3 to 2×1016 cm-3 and very high mobilities. Subsequently, Mg ions were selectively implanted to form p-type islands within the n-type drift layer. To reduce electric field crowding at the edge of the diode and to achieve high breakdown voltage, junction edge termination (JTE) and floating field rings (FFRs) were formed using Mg implantation. A high temperature, high-pressure post-implantation annealing process was carried out to activate the implanted Mg ions. As a result, we were able to demonstrate GaN JBS diodes with a breakdown voltage of 915 V and an on-resistance of 0.6 mΩ·cm2. These diodes exhibited a forward bias current density of 1 kA/cm2 at 1.5 V. Subsequently, we achieved GaN JBS diodes with a remarkable breakdown voltage of 1900 V and an on-resistance of 1.9 mΩ·cm2, capable of sustaining a forward bias current density of 0.5 kA/cm2 at 1.5 V. Importantly, the ON and OFF state performance of these GaN JBS diodes surpassed that of Si and SiC-based power diodes reported in existing literature. Lastly, we successfully grew 60 μm thick GaN:Si layers using HVPE with a carrier concentration of approximately 3 to 5×1015 cm-3. Based on simulation and empirical data these devices represent 5 kV GaN JBS power diodes, leveraging the developed processes in this project.
Explore the source record for details and available documents.
Not provided.
Highly conductive Ge-doped AlN with conductivity of 0.3 (Ω cm) −1 and electron concentration of 2 × 10 18 cm −3 was realized via a non-equilibrium process comprising ion implantation and annealing at a moderate thermal budget. Similar to a previously demonstrated shallow donor state in Si-implanted AlN, Ge implantation also showed a shallow donor behavior in AlN with an ionization energy ∼80 meV. Ge showed a 3× higher conductivity than its Si counterpart for a similar doping level. Photoluminescence spectroscopy indicated that higher conductivity for Ge-doped AlN was achieved primarily due to lower compensation. This is the highest n-type conductivity reported for AlN doped with Ge to date and demonstration of technologically useful conductivity in Ge-doped AlN.
Here we investigate the electrical characteristics of Ni Schottky contacts on n-type GaN films that have undergone ultra-high-pressure annealing (UHPA), a key processing step for activating implanted Mg. Contacts deposited on these films exhibit low rectification and high leakage current compared to contacts on as-grown films. By employing an optimized surface treatment to restore the GaN surface following UHPA, we obtain Schottky contacts with a high rectification ratio of ~10 9 , a near-unity ideality factor of 1.03, and a barrier height of ~0.9 eV. These characteristics enable the development of GaN junction barrier Schottky diodes employing Mg implantation and UHPA.
Near-field radiative heat transfer (NFRHT) between planar metallic surfaces was computationally explored over five decades ago by Polder and van Hove [Phys. Rev. B 4, 3303 (1971)]. These studies predicted that, as the gap size (d) between the surfaces decreased, the radiative heat flux first increases by several orders of magnitude until d is ~100 nm after which the heat flux saturates. However, despite both the fundamental and practical importance of these predictions, the combined enhancement and saturation of NFRHT at small gaps in metallic surfaces remains experimentally unverified. Here, we probe NFRHT between planar metallic (Pt, Au) surfaces and show that RHT rates can exceed the far-field rate by over a thousand times when d is reduced to ~25 nm. More importantly, we show that for small values of d RHT saturates due to the dominant contributions from transverse electric evanescent modes. Finally, our results are in excellent agreement with the predictions of fluctuational electrodynamics and are expected to inform the development of technologies such as near-field thermophotovoltaics, radiative heat-assisted magnetic recording, and nanolithography.
Here we report a kV class, low ON-resistance, vertical GaN junction barrier Schottky (JBS) diode with selective-area p-regions formed via Mg implantation followed by high-temperature, ultra-high pressure (UHP) post-implantation activation anneal. The JBS has an ideality factor of 1.03, a turn-on voltage of 0.75 V, and a specific differential ON-resistance of 0.6 mΩ·cm 2 . The breakdown voltage of the JBS diode is 915 V, corresponding to a maximum electric field of 3.3 MV cm –1 . These results underline that high-performance GaN JBS can be realized using Mg implantation and high-temperature UHP post-activation anneal.
In this Letter, we unveil the high-temperature limits of N-polar GaN Schottky contacts enhanced by a low-pressure chemical vapor deposited (LPCVD) SiN interlayer. Compared to conventional Schottky diodes, the insertion of a 5 nm SiN lossy dielectric interlayer in-between Ni and N-polar GaN increases the turn-on voltage (V ON ) from 0.4 to 0.9 V and the barrier height ($\phi_B$) from 0.4 to 0.8 eV. This modification also reduces the leakage current at zero bias significantly: at room temperature, the leakage current in the conventional Schottky diode is >103 larger than that observed in the device with the SiN interlayer, while at 200 °C, this ratio increases to 105. Thus, the rectification ratio (ION/IOFF) at ±1.5 V reduces to less than one at 250 °C for the conventional Schottky diode, whereas for SiN-coated diodes, rectification continues until 500 °C. The I–V characteristics of the diode with an SiN interlayer can be recovered after exposure to 400 °C or lower. Contact degradation occurs at 500 °C, although devices are not destroyed yet. Here, we report N-polar GaN Schottky contact operation up to 500 °C using an LPCVD SiN interlayer.
The ultra-wide bandgap of Al-rich AlGaN is expected to support a significantly larger breakdown field compared to GaN, but the reported performance thus far has been limited by the use of foreign substrates. In this Letter, the material and electrical properties of Al 0.85 Ga 0.15 N/Al 0.6 Ga 0.4 N high electron mobility transistors (HEMT) grown on a 2-in. single crystal AlN substrate are investigated, and it is demonstrated that native AlN substrates unlock the potential for Al-rich AlGaN to sustain large fields in such devices. We further study how Ohmic contacts made directly to a Si-doped channel layer reduce the knee voltage and increase the output current density. High-quality AlGaN growth is confirmed via scanning transmission electron microscopy, which also reveals the absence of metal penetration at the Ohmic contact interface and is in contrast to established GaN HEMT technology. Two-terminal mesa breakdown characteristics with 1.3 μm separation possess a record-high breakdown field strength of ~11.5 MV/cm for an undoped Al 0.6 Ga 0.4 N-channel layer. The breakdown voltages for three-terminal devices measured with gate-drain distances of 4 and 9 μm are 850 and 1500 V, respectively.
Not provided.
Quantifying the temperature of microdevices is critical for probing nanoscale energy transport. Such quantification is often accomplished by integrating resistance thermometers into microdevices. However, such thermometers frequently become structurally unstable and fail due to thermal stresses at elevated temperatures. Here, we show that custom-fabricated scanning thermal probes (STPs) with a sharp tip and an integrated heater/thermometer can accurately measure the temperature of microdevices held at elevated temperatures. This measurement is accomplished by introducing a modulated heat input to the STP after contacting the microdevice with the STP's tip and characterizing the DC and AC components of the STP's temperature. From these measured temperature components, the tip-to-sample thermal resistance and the microdevice surface temperature are deduced simultaneously via a simple lumped-capacitance model. The advances presented here can greatly facilitate temperature measurements of a variety of heated microdevices.
In this work, we study the behavior of N-polar GaN Schottky diodes with low-pressure chemical vapor deposited (LPCVD) SiN interlayers and unveil the important role of an amphoteric miniband formed in this interlayer due to a previously identified and dominating Si dangling bond defect. Through analysis of temperature-dependent current–voltage (I–V–T), capacitance–voltage (C–V), and x-ray photoelectron spectroscopy measurements, we observe that when nickel is deposited on LPCVD SiN pretreated with hydrofluoric acid, the SiN/GaN interface is responsible for determining the overall system's barrier height. By contrast, contact formation on oxidized LPCVD SiN leads to a metal/SiN-dominant barrier. We, consequently, propose band diagrams that account for an amphoteric miniband in LPCVD SiN, leading to a new understanding of LPCVD SiN as a lossy dielectric with surface barrier-dependent behavior.