Engineering topics

Rauschenbach, H. S.

Publications and source records attributed to Rauschenbach, H. S..

11 records

NASA NTRS1984

Solar cell degradation in proton radiation orbits

Significant discrepancies have been observed between predicted and actual in-orbit silicon solar array degradation in orbits other than LEO (low Earth orbits) and GEO (geosynchronous orbit). These discrepancies have been diagnosed to arise probably from a combination of a lack of appropriate solar cell test data and from inadequacies in the models that relate the unidirectional and mono-energetic proton test data to the omnidirectional flux-energy spectra actually found in orbit. Relative damage coefficients and solar cell power outputs were discussed, and also were presented in graph form. Silicon and gallium arsenide solar cells were considered.

Rauschenbach, H. S.↗

NASA NTRS1982

Miniaturized Cassegrainian concentrator concept demonstration

High concentration ratio photovoltaic systems for space applications have generally been considered impractical because of perceived difficulties in controlling solar cell temperatures to reasonably low values. A miniaturized concentrator system is now under development which surmounts this objection by providing acceptable solar cell temperatures using purely passive cell cooling methods. An array of identical miniaturized, rigid Cassegrainian optical systems having a low f-number with resulting short dimensions along their optical axes are rigidly mounted into a frame to form a relatively thin concentrator solar array panel. A number of such panels, approximately 1.5 centimeters thick, are wired as an array and are folded against one another for launch in a stowed configuration. Deployment on orbit is similar to the deployment of conventional planar honeycomb panel arrays or flexible blanket arrays. The miniaturized concept was conceived and studied in the 1978-80 time frame. Progress in the feasibility demonstration to date is reported.

Patterson, R. E.↗

NASA NTRS1981

Low cost, high concentration ratio solar cell array for space applications

A miniaturized Cassegrainian-type concentrator solar array concept for space applications is described. In-orbit cell operating temperatures near 80 C are achieved with purely passive cell cooling and a net concentration ratio of 100. A multiplicity of miniaturized, rigid solar cell concentrator subassemblies are electrically interconnected in conventional fashion and mounted into rigid frames to form concentrator solar panel assemblies approximately 14-mm thick. A plurality of such interconnected panels forms a stowable and deployable solar cell blanket. It is projected that for 20% efficient silicon cells an array of 500 kW beginning-of-life output capability, including orbiter cradle structures, can be transported by a single shuttle orbiter flight into low earth orbit. In-orbit array specific performance is calculated to be approximately 100 W/sq m and 20 W/kg, including all stowage, deployment and array figure control equipment designed for a 30-year orbital life. Higher efficiency gallium arsenide and multiple band gap solar cells will improve these performance factors correspondingly.

Patterson, R. E.↗

NASA NTRS1980

Solar cell array design handbook - The principles and technology of photovoltaic energy conversion

Photovoltaic solar cell array design and technology for ground-based and space applications are discussed from the user's point of view. Solar array systems are described, with attention given to array concepts, historical development, applications and performance, and the analysis of array characteristics, circuits, components, performance and reliability is examined. Aspects of solar cell array design considered include the design process, photovoltaic system and detailed array design, and the design of array thermal, radiation shielding and electromagnetic components. Attention is then given to the characteristics and design of the separate components of solar arrays, including the solar cells, optical elements and mechanical elements, and the fabrication, testing, environmental conditions and effects and material properties of arrays and their components are discussed.

Rauschenbach, H. S.↗

NASA NTRS1977

Solar-cell array design handbook

Twelve-chapter two-volume compilation of solar cell design data is written from industrial, university, and governmental sources. Volumes contain tutorial descriptions of analytical methods, solar-cell characteristics, and cell material properties widely used in specifying solar-cell array performance and hardware design, as well as analysis, fabrication, and test methods.

Rauschenbach, H. S.↗

NASA NTRS1976

Flexible, FEP-Teflon covered solar cell module development

Techniques and equipment were developed for the large scale, low-cost fabrication of lightweight, roll-up and fold-up, FEP-Teflon encapsulated solar cell modules. Modules were fabricated by interconnecting solderless single-crystal silicon solar cells and heat laminating them at approximately 300 C between layers of optically clear FEP and to a loadbearing Kapton substrate sheet. Modules were fabricated from both conventional and wraparound contact solar cells. A heat seal technique was developed for mechanically interconnecting modules into an array. The electrical interconnections for both roll-up and fold-up arrays were also developed. The use of parallel-gap resistance welding, ultrasonic bonding, and thermocompression bonding processes for attaching interconnects to solar cells were investigated. Parallel-gap welding was found to be best suited for interconnecting the solderless solar cells into modules. Details of the fabrication equipment, fabrication processes, module and interconnect designs, environmental test equipment, and test results are presented.

Rauschenbach, H. S.↗

NASA NTRS1976

Solar cell array design handbook, volume 1

Twelve chapters discuss the following: historical developments, the environment and its effects, solar cells, solar cell filters and covers, solar cell and other electrical interconnections, blocking and shunt diodes, substrates and deployment mechanisms, material properties, design synthesis and optimization, design analysis, procurement, production and cost aspects, evaluation and test, orbital performance, and illustrative design examples. A comprehensive index permits rapid locating of desired topics. The handbook consists of two volumes: Volume 1 is of an expository nature while Volume 2 contains detailed design data in an appendix-like fashion. Volume 2 includes solar cell performance data, applicable unit conversion factors and physical constants, and mechanical, electrical, thermal optical, magnetic, and outgassing material properties. Extensive references are provided.

Rauschenbach, H. S.↗

NASA NTRS1976

Solar cell electrical connections

Study was conducted to find best methods of attaching pure silver and silver plated Kovar (trademark) interconnect ribbons to silicon solar cells with titanium-silver solderless contacts. Investigations include thermocompression bonding, parallel-gap welding, and ultrasonic welding.

Rauschenbach, H. S.↗

NASA NTRS1975

FEP-TEFLON encapsulated solar cell modules Further progress

A progress report, starting with November 1973, is given in the design, development, and performance of lightweight flexible FET (Fluorinated Ethylene Propylene) encapsulated solar cell modules intended to form standardized building blocks for large roll-up or fold-up solar cell blankets with performances on the order of 100 W/sq m and 80 W/kg in near space. It is shown that interconnected FEP encapsulated modules of advanced design can withstand all typical ground handling, assembly, storage, and launch conditions, and are well suited for high-power space applications.

Rauschenbach, H. S.↗

NASA NTRS1974

FEP-Teflon covered solar cell array advancements

Progress is reported on the design and development of lightweight, flexible, FEP encapsulated solar cell modules. Such modules are intended to form standardized building blocks for larger roll-up or fold-up solar cell blankets having specific performance in the order of 100 W/sq m and 80 W/kg in space near earth. Modules are constructed by heat-laminating interconnected 200-micron thick single crystal silicon solar cells with solderless front and back contacts between two layers of clear FEP. The outer FEP layer is 125 microns thick and serves as the solar cell cover material. The inner layer is 50 microns thick and serves as the adhesive between the solar cells and a 25-micron thick loadbearing Kapton substrate sheet.

Rauschenbach, H. S.↗

NASA NTRS1972

Breakdown phenomena in reverse biased silicon solar cells.

Solar cell reverse current-voltage characteristics have been found to vary widely and to be generally unstable. At reverse voltages greater than approximately 20 V and at cell power dissipations of more than 4 W, the probability of permanent breakdown, resulting in cell short-circuit failure, was found to increase with increasing voltage and exposure time. Shorted cells showed evidence of cell contact material and silicon melting in very localized areas with lava-like flow patterns and channels bridging the p and n contacts.

Rauschenbach, H. S.↗