Engineering Papers⌕ Search

Engineering topics

Rasky, Daniel J.

Publications and source records attributed to Rasky, Daniel J..

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Coupled Ablation, Heat Conduction, Pyrolysis, Shape Change and Spallation of the Galileo Probe

The Galileo probe enters the atmosphere of Jupiter in December 1995. This paper presents numerical methodology and detailed results of our final pre-impact calculations for the heat shield response. The calculations are performed using a highly modified version of a viscous shock layer code with massive radiation coupled with a surface thermochemical ablation and spallation model and with the transient in-depth thermal response of the charring and ablating heat shield. The flowfield is quasi-steady along the trajectory, but the heat shield thermal response is dynamic. Each surface node of the VSL grid is coupled with a one-dimensional thermal response calculation. The thermal solver includes heat conduction, pyrolysis, and grid movement owing to surface recession. Initial conditions for the heat shield temperature and density were obtained from the high altitude rarefied-flow calculations of Haas and Milos. Galileo probe surface temperature, shape, mass flux, and element flux are all determined as functions of time along the trajectory with spallation varied parametrically. The calculations also estimate the in-depth density and temperature profiles for the heat shield. All this information is required to determine the time-dependent vehicle mass and drag coefficient which are necessary inputs for the atmospheric reconstruction experiment on board the probe.

Milos, Frank S.↗
NASA NTRS1995

Effect of Cyclic Aeroconvective Heating on Flexible Thermal Insulations

This paper describes the effect of cyclic aeroconvective heating on the thermal performance of ceramic flexible insulations considered for potential use as thermal protection systems or thermal insulations for future hypersonic vehicles such as the Reusable Launch Vehicles (RLV's) and other applications where structures require thermal protection from severe heating. The thermal response of these materials after exposure to cyclic aeroconvective heating from a plasma arc is described. The thermal insulations evaluated were Composite Flexible Blanket Insulations composed of an outer layer of aluminoborosilicate fabric and alumina insulation. The insulations were evaluated with and without a high emissivity coating. These insulations were exposed to the plasma arc stream for nine minutes reaching surface temperatures of 1150 C and a heat flux of 10.5 W/sq cm. Insulations were exposed three, six, or nine times in order to demonstrate reusability and to determine the effect oi coatings on the surface durability of these insulations. Test results demonstrated the capability of these insulations to protect either composite or metallic structures from high heating environments. It is shown that high emittance coatings reduce backface temperatures. The durability of these insulations when impacted at low velocities was also demonstrated. The interaction of the coatings with the ceramic fibers was characterized. An analytical thermal model was utilized to correlate experimental thermal test results with calculated values.

Kourtides, Demetrius A.↗
NASA NTRS1994

Review of numerical procedures for computational surface thermochemistry

Models and equations for surface thermochemistry and near-surface thermophysics of aerodynamically heated thermal protection materials are reviewed, with particular emphasis on computational boundary conditions for surface mass and energy transfer. The surface energy and mass balances, coupled with an appropriate ablation or surface catalysis model, provide complete thermochemical boundary conditions for a true multidisciplinary solution of the fully coupled fluid-dynamics/solid mechanics problem. Practical approximate solutions can be obtained by using a detailed model with full thermophysics for either the solid or fluid phase and a semianalytic method for the other half of the problem. A significant increase in the state-of-the-art in aerothermal computational fluid dynamics is possible by uniting computational fluid dynamic (CFD) methodology with surface thermochemistry boundary conditions and the heat-balance-integral method.

SOLID MECHANICS↗
NASA NTRS1994

Light Weight Ceramic Ablators for Mars Follow-on Mission Vehicle Thermal Protection System

New Light Weight Ceramic Ablators (LCA) were produced by using ceramic and carbon fibrous substrates, impregnated with silicone and phenolic resins. The special infiltration techniques (patent pending) were developed to control the amount of organic resins in the highly porous fiber matrices so that the final densities of LCA's range from 0.22 to 0.24 g/cc. This paper presents the thermal and ablative performance of the Silicone Impregnated Reusable Ceramic Ablators (SIRCA) in simulated entry conditions for Mars-Pathfinder in the Ames 60 MW Interaction Heating Facility (I HF). Arc jet test results yielded no evidence of char erosion and mass loss at high stagnation pressures to 0.25 atm. Minimal silica melt was detected on surface char at a stagnation pressure of 0.31 atm. Four ceramic substrates were used in the production of SIRCA's to obtain the effective of boron oxide present in substrate so the thermal performance of SIRCA's. A sample of SIRCA was also exposed to the same heating condition for five cycles and no significant mass loss or recession was observed. Tensile testing established that the SIRCA tensile strength is about a factor of two higher than that of the virgin substrates. Thermogravimetric Analysis (TGA) of the char in nitrogen and air showed no evidence of free carbon in the char. Scanning Electron Microscopy of the post test sample showed that the char surface consists of a fibrous structure that was sealed with a thin layer of silicon oxide melt.

Tran, Huy K.↗
NASA NTRS1994

Uses of Advanced Ceramic Composites in the Thermal Protection Systems of Future Space Vehicles

Current ceramic composites being developed and characterized for use in the thermal protection systems (TPS) of future space vehicles are reviewed. The composites discussed include new tough, low density ceramic insulation's, both rigid and flexible; ultra-high temperature ceramic composites; nano-ceramics; as well as new hybrid ceramic/metallic and ceramic/organic systems. Application and advantage of these new composites to the thermal protection systems of future reusable access to space vehicles and small spacecraft is reviewed.

Rasky, Daniel J.↗
NASA NTRS1994

Comparison of Coupled Radiative Navier-Stokes Flow Solutions with the Project Fire II Flight Data

A nonequilibrium, axisymmetric, Navier-Stokes flow solver with coupled radiation has been developed to use in the design of thermal protection systems for vehicles where radiation effects are important. The present method has been compared with an existing flow and radiation solver and with the Project Fire II experimental data. Very good agreement has been obtained over the entire Fire II trajectory with the experimentally determined values of the stagnation radiation intensity in the .2 to 6.2 eV range and with the total stagnation heating. The agreement was significantly better than previous numerical predictions. The effects of a number of flow models are examined to determine which combination of physical models produces the best agreement with the experimental data. These models include radiation coupling, multi-temperature thermal models, finite-rate chemistry, and a quasi-steady-state or Boltzmann assumption for the calculation of the excited electronic states. Finally, the computational efficiency of the present model is evaluated. The radiation properties model developed for this study is shown to offer significant computational savings compared to existing codes.

Olynick, David R.↗
NASA NTRS1994

Navier-Stokes Calculations For a Venus Composition Probe With Ablation And Wake Radiation

A numerical investigation is carried out to determine the magnitude of wake radiation for a proposed Venus composition probe. One of the scientific goals of the mission is to determine the atmospheric composition of Venus by examining the intensity of scattered sunlight through the wake of the vehicle during planetary entry. In the wake of the vehicle, excited particles generated in the bow shock and boundary layers absorb and emit radiation. Thus, the purpose of this study is to determine if the radiation sensor will be able to sense the incoming solar radiative flux relative to the radiative flux generated in the wake. During portions of the entry trajectory the incident surface heat flux will be high enough to produce significant ablation. Ablation products such as CN are known to be strong radiators. Also, the ablation will be driven by strong radiation emanating from the bow shock. Thus, radiation and ablation will be coupled into the Navier-Stokes flow solutions.

Olynick, David R.↗
NASA NTRS1994

Chemical Composition and Flow Velocity as a Function of Operating Conditions for an Arc Jet Heater

We have used laser-induced fluorescence (LIF) to carry out a detailed, systematic survey of the properties of the free stream of the 20 Megawatt Aerodynamic Heating Facility at NASA/Ames Research Center. In both air and nitrogen flows we have measured the atomic nitrogen absolute number density and flow velocity at each operating condition. In air flows we have also measured the atomic oxygen absolute number density and rotational/translational temperature at each operating condition. These results have been used to provide, for the first time, a direct, nonintrusive measurement of the enthalpy on the centerline of the flow. In addition, the observed arc jet properties can be used to test and improve computer simulations of the arc jet flow which include detailed chemical rate processes (especially nitrogen atom recombination) taking place during the supersonic expansion.

Bamford, Douglas J.↗
NASA NTRS1994

General Model for Multicomponent Ablation Thermochemistry

A previous paper (AIAA 94-2042) presented equations and numerical procedures for modeling the thermochemical ablation and pyrolysis of thermal protection materials which contain multiple surface species. This work describes modifications and enhancements to the Multicomponent Ablation Thermochemistry (MAT) theory and code for application to the general case which includes surface area constraints, rate limited surface reactions, and non-thermochemical mass loss (failure). Detailed results and comparisons with data are presented for the Shuttle Orbiter reinforced carbon-carbon oxidation protection system which contains a mixture of sodium silicate (Na2SiO3), silica (SiO2), silicon carbide (SiC), and carbon (C).

Milos, Frank S.↗
NASA NTRS1994

Effect of Porosity on Surface Catalytic Efficiency

This paper describes the effect of surface porosity of thermal protection materials on surface catalytic efficiency using test data taken from both arc-jet and side-arm reactor facilities. Relative surface porosity of the samples varied from 6% to 50%. Surface porosity was measured using a flow apparatus and Bernoulli equation. The surface catalytic efficiency of the materials was calculated using aerothermodynamic, and kinetic theories. The catalytic efficiency of the materials are compared at surface temperatures between room temperature and 2500 F. The data are presented in the form of graphs and tables.

Stewart, David A.↗
NASA NTRS1994

The Influence of SiC on the Ablation Response of Advanced Refractory Composite Materials

In continuing our studies of advanced refractory composite materials we have recently completed an arc-jet test series of a diverse group of ceramics and ceramic matrix composites. The compositions range from continuous fiber reinforced ceramics to monoliths. Many of these materials contain SiC and one objective of this test series was to identify the influence of SiC oxidation mechanisms on material performance. Hence the arc heater was operated at two conditions; one in which the passive oxidation of SiC would be dominant and the other where the active oxidation of SiC would be dominant. It is shown here that the active oxidation mechanism of SiC does not dominate material performance when it is present at levels equal to or below 20 volume percent.

Bull, Jeffrey D.↗
NASA NTRS1993

Thermal response and ablation characteristics of light weight ceramic ablators

An account is given of the thermal performance and ablation characteristics of the NASA-Ames Lightweight Ceramic Ablators (LCAs) in supersonic, high-enthalpy convective environments, which use low density ceramic or carbon fiber matrices as substrates for main structural support, with organic resin fillers. LCA densities are in the 0.224-1.282 g/cu cm range. In-depth temperature data have been obtained to determine thermal penetration depths and conductivity. The addition of SiC and PPMA is noted to significantly improve the ablation performance of LCAs with silica substrates. Carbon-based LCAs are the most mass-efficient at high flux levels.

Tran, Huy K.↗
NASA NTRS1993

Entry Systems Panel

As general findings, lessons learned from shuttle are: (1) bridge established between development center (JSC) Research Centers (ARC, LARC), and industry (RI, LMSC, Corning, Mansville, 3M LTV, Union Carbide, Hexcel) for shuttle TPS; (2) not all test results adequately analyzed or in hindsight, completely encompassing all failure modes; (3) gap heating effects from ground facilities not totally indicative of flight experience; (4) need to design with operations in mind (not just to cost) example: moisture intrusion of GR/EP, many other examples; (5) RSI- developed as point design for maneuvering entry vehicle of high L/D; and (6) RSI - 15 years from invention to use on flight hardware.

Rasky, Daniel J.↗
NASA NTRS1993

Entry Systems Panel deliberations

The Entry Systems Panel was chaired by Don Rummler, LaRC and Dan Rasky, ARC. As requested, each panel participant prior to the workshop prepared and delivered presentations to: (1) identify technology needs; (2) assess current programs; (3) identify technology gaps; and (4) identify highest payoff areas R&D. Participants presented background on the entry systems R&D efforts and operations experiences for the Space Shuttle Orbiter. These participants represented NASA Centers involved in research (Ames Research Center), development (Johnson Space Center) and operations (Kennedy Space Center) and the Shuttle Orbiter prime contractor. The presentations lead to the discovery of several lessons learned.

Rasky, Daniel J.↗
NASA NTRS1993

Thermal protection materials at NASA Ames Research Center

The topics addressed are: (1) Space Exploration Initiative (SEI); (2) Aeroassist Flight Experiment (AFE); (3) Mars Environmental Survey (MESUR); (4) National Aero-space Plan (NASP); (5) Pegasus and Pegasus/SWERVE Hypersonic Testing; and (6) Personnel Launch System TPS evaluation.

Rasky, Daniel J.↗
NASA NTRS1992

Advanced ceramic matrix composites for TPS

Recent advances in ceramic matrix composite (CMC) technology provide considerable opportunity for application to future aircraft thermal protection system (TPS), providing materials with higher temperature capability, lower weight, and higher strength and stiffness than traditional materials. The Thermal Protection Material Branch at NASA Ames Research Center has been making significant progress in the development, characterization, and entry simulation (arc-jet) testing of new CMC's. This protection gives a general overview of the Ames Thermal Protection Materials Branch research activities, followed by more detailed descriptions of recent advances in very-high temperature Zr and Hf based ceramics, high temperature, high strength SiC matrix composites, and some activities in polymer precursors and ceramic coating processing. The presentation closes with a brief comparison of maximum heat flux capabilities of advanced TPS materials.

Rasky, Daniel J.↗
NASA NTRS1992

Numerical procedures for three-dimensional computational surface thermochemistry

Models and equations for surface thermochemistry and near-surface thermophysics of aerodynamically-heated thermal protection materials are reviewed, with particular emphasis on computational boundary conditions for surface mass and energy transfer. The surface energy and mass balances, coupled with an appropriate ablation or surface catalysis model, provide complete thermochemical boundary conditions for a true multidisciplinary solution of the fully coupled fluid-dynamics/solid mechanics problem. Practical approximate solutions can be obtained by using a detailed model with full thermophysics for either the solid or fluid phase amd a semianalytic method for the other half of the problem. A significant increase in the state-of-the-art in aerothermal computational fluid dynamics is possible by uniting CFD methodology with surface thermochemistry boundary conditions and the heat-balance-integral method.

Milos, Frank S.↗