Distinguishing mechanisms of morphological instabilities in phase change materials during switching
Not Available
Engineering topics
Publications and source records attributed to Raoux, S.
Not Available
Abstract not provided
Chalcogenide-based phase-change materials have wide use in optical recording media and are growing in importance for use in non-volatile electronic memory. For both applications, rapid switching between the amorphous and crystalline phases is necessary, and understanding the changes during rapidly driven phase transitions is of scientific and technological significance. Laser-induced crystallization and amorphization occur rapidly and changes in atomic structure, microstructure, and temperature are difficult to observe experimentally and determine computationally. We have used nanosecond-scale time-resolved diffraction with intense electron pulses to study Ge{sub 2}Sb{sub 2}Te{sub 5} during laser crystallization. Using a unique and unconventional specimen geometry, cycling between the amorphous and crystalline phases was achieved, enabling in situ transmission electron microscope (TEM) study of both microstructural and crystallographic changes caused by repeated switching. Finite element analysis was used to simulate interactions of the laser with the nano-structured specimens and to model the rapidly changing specimen temperature. Such time-resolved experimental methods combined with simulation of experimentally inaccessible physical characteristics will be fundamental to advancing the understanding of rapidly driven phase transformations.
The question of the nature and stability of polar ordering in nanoscale ferroelectrics is examined with colloidal nanocrystals of germanium telluride (GeTe). We provide atomic-scale evidence for room-temperature polar ordering in individual nanocrystals using aberration-corrected transmission electron microscopy and demonstrate a reversible, size-dependent polar-nonpolar phase transition of displacive character in nanocrystal ensembles. A substantial linear component of the distortion is observed, which is in contrast with theoretical reports predicting a toroidal state.
The chemical and structural effects of processing on the crystallization of nitrogen doped Ge{sub 2}Sb{sub 2}Te{sub 5} is examined via x-ray photoelectron spectroscopy (XPS), x-ray absorption spectroscopy (XAS), time resolved laser reflectivity, and time resolved x-ray diffraction (XRD). Time resolved laser reflectivity and XRD show that exposure to various etch and ash chemistries significantly reduces the crystallization speed while the transition temperature from the rocksalt to the hexagonal phase is increased. XPS and XAS attribute this to the selective removal and oxidization of N, Ge, Sb, and Te, thus altering the local bonding environment to the detriment of device performance.
The stoichiometric Ga{sub 4}Sb{sub 6}Te{sub 3} and Ga-Sb materials were systematically studied. The alloy Ga{sub 4}Sb{sub 6}Te{sub 3} shows a fast crystallization speed, very high crystallization temperature, T{sub x}, and high electrical contrast. Although stoichiometric GaSb has similar performance and even faster crystallization speed, the electrical contrast is much lower. The other off-stoichiometric compounds we studied all have higher T{sub x} than Ge{sub 2}Sb{sub 2}Te{sub 5} indicating a good amorphous stability. By raising the Sb/Te ratio with GaSb incorporation, T{sub x} and the recrystallization time of melt-quenched, amorphous samples can be effectively increased. The stoichiometric Ga{sub 4}Sb{sub 6}Te{sub 3} with less likelihood of phase-segregation compared to nonstoichiometric compounds is a promising candidate for phase-change memory.
The crystallization times of Ge-Te phase change materials with variable Ge concentrations (29.5-72.4 at. %) were studied. A very strong dependence of the crystallization time on the composition for as-deposited, amorphous films was confirmed, with a minimum for the stoichiometric composition GeTe. The dependence is weaker for melt-quenched, amorphous material and crystallization times are between one to almost four orders of magnitude shorter than for as-deposited materials. This is promising for applications because recrystallization from the melt-quenched phase is the relevant process for optical and solid state memory, and fast crystallization and weak dependence on compositional variations are desirable.
Phase transformations are ubiquitous, fundamental phenomena that lie at the heart of many structural, optical and electronic properties in condensed matter physics and materials science. Many transformations, especially those occurring under extreme conditions such as rapid changes in the thermodynamic state, are controlled by poorly understood processes involving the nucleation and quenching of metastable phases. Typically these processes occur on time and length scales invisible to most experimental techniques ({micro}s and faster, nm and smaller), so our understanding of the dynamics tends to be very limited and indirect, often relying on simulations combined with experimental study of the ''time infinity'' end state. Experimental techniques that can directly probe phase transformations on their proper time and length scales are therefore key to providing fundamental insights into the whole area of transformation physics and materials science. LLNL possesses a unique dynamic transmission electron microscope (DTEM) capable of taking images and diffraction patterns of laser-driven material processes with resolution measured in nanometers and nanoseconds. The DTEM has previously used time-resolved diffraction patterns to quantitatively study phase transformations that are orders of magnitude too fast for conventional in situ TEM. More recently the microscope has demonstrated the ability to directly image a reaction front moving at {approx}13 nm/ns and the nucleation of a new phase behind that front. Certain compound semiconductor phase change materials, such as Ge{sub 2}Sb{sub 2}Te{sub 5} (GST), Sb{sub 2}Te and GeSb, exhibit a technologically important series of transformations on scales that fall neatly into the performance specifications of the DTEM. If a small portion of such material is heated above its melting point and then rapidly cooled, it quenches into an amorphous state. Heating again with a less intense pulse leads to recrystallization into a vacancy-stabilized metastable rock salt structure. Each transformation takes {approx}10-100 ns, and the cycle can be driven repeatedly a very large number of times with a nanosecond laser such as the DTEM's sample drive laser. These materials are widely used in optical storage devices such as rewritable CDs and DVDs, and they are also applied in a novel solid state memory technology - phase change memory (PCM). PCM has the potential to produce nonvolatile memory systems with high speed, extreme density, and very low power requirements. For PCM applications several materials properties are of great importance: the resistivities of both phases, the crystallization temperature, the melting point, the crystallization speed, reversibility (number of phase-transformation cycles without degradation) and stability against crystallization at elevated temperature. For a viable technology, all these properties need to have good scaling behavior, as dimensions of the memory cells will shrink with every generation. In this LDRD project, we used the unique single-shot nanosecond in situ experimentation capabilities of the DTEM to watch these transformations in GST on the time and length scales most relevant for device applications. Interpretation of the results was performed in conjunction with atomistic and finite-element computations. Samples were provided by collaborators at IBM and Stanford University. We observed, and measured the kinetics of, the amorphous-crystalline and melting-solidification transitions in uniform thin-film samples. Above a certain threshold, the crystal nucleation rate was found to be enormously high (with many nuclei appearing per cubic {micro}m even after nanosecond-scale incubation times), in agreement with atomistic simulation and consistent with an extremely low nucleation barrier. We developed data reduction techniques based on principal component analysis (PCA), revealing the complex, multi-dimensional evolution of the material while suppressing noise and irrelevant information. Using a novel specimen geometry, we also achieved repeated switching between the amorphous and crystalline phases enabling in situ study of structural change after phase cycling, which is relevant to device performance. We also observed the coupling between the phase transformations and the evolution of morphology on the nanometer scale, revealing the gradual development of striations in uniform films and preferential melting at sharp edges in laser-heated nanopatterned GST. This nonuniform melting, interpreted through simulation as being a direct result of geometrical laser absorption effects, appears to be responsible for a marked loss in morphological stability even at moderate laser intensities and may be an important factor in the longevity of nanostructured phase change materials in memory applications.
The stability of the crystalline phase of binary phase-change Ge{sub x}Sb{sub 1-x} films is investigated over a wide range of Ge content. From Raman spectroscopy we find the Ge-Sb crystalline structure irreversibly altered after exposure to a laser beam. We show that with increasing beam intensity/temperature Ge agglomerates and precipitates out in the amount growing with x. A simple empirical relation links Ge precipitation temperature T{sub Ge}{sup p} to the rate of change dT{sub cryst}/dx of crystallization, with the precipitation easiest on the mid-range x plateau, where T{sub cryst} is nearly constant. Our findings point to a preferable 15% < or approx. x < 50% window, that may achieve the desired cycling/archival properties of a phase-change cell.
Colloidal nanocrystals have long been used to study the dependence of phase stability and transitions on size. Both structural phase stability and phase transitions change dramatically in the nanometre size regime where the surface plays a significant role in determining the overall energetics of the system. We investigate the solid-solid phase transformation of crystallization in amorphous GeTenanoparticles. We report a colloidal synthetic route to amorphous GeTenanoparticles. Using in situ X-ray diffraction while heating, we observe the crystallization of the nanoparticles and find a dramatic increase of the crystallization temperature of over 150 C above the bulk value. Using size-selected nanoparticle films, we show that the crystallization temperature depends strongly on the particle size. In addition, we measure the electrical resistance of nanoparticle films and observe over 5 orders of magnitude lower resistance for the crystalline film compared to the amorphous film. Finally, we discuss the implications of the size-dependence of crystallization in the context of both understanding the behavior of phase stability in the nanosize regime and applications to phase change memory devices.
Phase transitions in GeTe/SnSe and Ge{sub 2}Se{sub 3}/SnTe are investigated using time resolved x-ray diffraction. GeTe exhibits a structural transition from rhombohedral to the cubic phase at 300 C, which is - 100 C lower than that of pure GeTe. This is facilitated by incorporation of Sn from SnSe. Sn migration is observed explicitly in Ge{sub 2}Se{sub 3}/SnTe by separation of SnSe phase. Amorphous Ge{sub 2}Se{sub 3} is also found to crystallize at a lower temperature of 300 C resulting in orthorhombic GeSe and monoclinic GeSe{sub 2}. Thus, inclusion of a Sn containing layer may offer a means to tailor phase transition in Ge-chalcogenide thin films for phase change memory applications.
Thin films of the phase change material Ge-Sb with Ge concentrations between 7.3 and 81.1 at. % were deposited by cosputtering from elemental targets. Their crystallization behavior was studied using time-resolved x-ray diffraction, Auger electron spectroscopy, differential scanning calorimetry, x-ray reflectivity, profilometry, optical reflectivity, and resistivity versus temperature measurements. It was found that the crystallization temperature increases with Ge content. Calculations of the glass transition temperature (which is a lower limit for the crystallization temperature T{sub x}) also show an increase with Ge concentration closely tracking the measured values of T{sub x}. For low Ge content samples, Sb x-ray diffraction peaks occurred during a heating ramp at lower temperature than Ge diffraction peaks. The appearance of Ge peaks is related to Ge precipitation and agglomeration. For Ge concentrations of 59.3 at. % and higher, Sb and Ge peaks occurred at the same temperature. Upon crystallization, film mass density and optical reflectivity increase as well as electrical contrast (ratio of resistivity in amorphous phase to crystalline phase) all showed a maximum for the eutectic alloy (14.5 at. % Ge). For the alloy with 59.3 at. % Ge there was very little change in any of these parameters, while the alloy with 81.1 at. % Ge behaved opposite to a typical phase change alloy and showed reduced mass density and reflectivity and increased resistivity.
The crystallization of amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} (GST) doped with nitrogen is studied with pulsed laser heating. The crystallization time of sputter-deposited films is increased by doping by as much as 100 times for nitrogen concentrations of the order of 12% in as-deposited amorphous films. Suppression of the formation of critical crystal nuclei is found to be responsible. The crystallization of melt-quenched amorphous material is also slowed by doping but less dramatically.
The crystallization temperature Tx of the phase change material Ge-Sb as a function of film thickness and cladding material was measured using time-resolved x-ray diffraction. For films >5 nm, a weak influence of the cladding material on Tx was found (increase for Si, SiN, Pt, SiC, and TiN and decrease for Al and W). For very thin films, however, Tx differed up to 200?C. Doping of Ge-Sb with these materials led to an increase in Tx in all cases, up to a maximum of 180?C for SiN. Such a large influence of interfaces and doping on Tx is of great technological importance.
Resistivity versus temperature measurements and time-resolved x-ray diffraction were used to study Ge-Te phase change materials. Resistivity versus temperature measurements showed one sharp drop in resistivity for films with 30, 50, and 70 at.?% Ge, two steps for films with 40 at.?% Ge, and a gradual transition for films with 60 at.?% Ge. Films with 30, 50, and 70 at.?% Ge crystallized in a single-step process with GeTe and Te, only GeTe, and GeTe and Ge diffraction peaks, respectively. Films with 40 and 60 at.?% Ge crystallized in a two-step process with GeTe peaks appearing first and additional Te or Ge peaks, respectively, appearing at higher temperature.
Phase change materials can exist in two different phases, the amorphous and the crystalline phase, which exhibit distinctly different physical properties. It is possible to repeatedly switch the state of these materials, from the amorphous phase to the crystalline phase by heating the material above its crystallization temperature, and from the crystalline to the amorphous phase by melt-quenching. Phase change materials have been utilized very successfully in all modern optical re-writable storage media such as CDs, DVDs and Blu-ray disks. Recently, they have also been applied to solid-state memory devices where their large difference in electrical resistivity is used to store information. This paper reviews the unique properties of phase change materials in particular as they are important for their application to these devices.