Engineering topics

Ramaswamy, V. G.

Publications and source records attributed to Ramaswamy, V. G..

6 records

NASA NTRS1990

A constitutive model for the inelastic multiaxial response of Rene 80 at 871 C and 982 C

This paper contains an extension of the uniaxial state variable constitutive model of Ramaswamy et al. (1988) to the case of multiaxial loading. The correlation between uniaxial and multiaxial loading conditions is achieved through the assumptions of material isotropy and conservation of inelastic volume. The multiaxial extension is based only on the material parameters evaluated from uniaxial loading. The research is accompanied by a multiaxial experimental program to evaluate the response of Rene 80 at 871 C and 982 C. Experiments in the program include torsion, proportional axial and torsion, and nonproportional loading. It was shown experimentally that there is no extra hardening from the multiaxial loading than results from uniaxial loading. Further, it is shown that the multiaxial model is successful in predicting the experimental results using only the parameters determined from the uniaxial experiments.

Stouffer, D. C.↗

NASA NTRS1988

Development of a unified constitutive model for an isotropic nickel base superalloy Rene 80

Accurate analysis of stress-strain behavior is of critical importance in the evaluation of life capabilities of hot section turbine engine components such as turbine blades and vanes. The constitutive equations used in the finite element analysis of such components must be capable of modeling a variety of complex behavior exhibited at high temperatures by cast superalloys. The classical separation of plasticity and creep employed in most of the finite element codes in use today is known to be deficient in modeling elevated temperature time dependent phenomena. Rate dependent, unified constitutive theories can overcome many of these difficulties. A new unified constitutive theory was developed to model the high temperature, time dependent behavior of Rene' 80 which is a cast turbine blade and vane nickel base superalloy. Considerations in model development included the cyclic softening behavior of Rene' 80, rate independence at lower temperatures and the development of a new model for static recovery.

Ramaswamy, V. G.↗

NASA NTRS1986

A Constitutive Model for the Inelastic Multiaxial Cyclic Response of a Nickel Base Superalloy Rene 80

The objective was to develop unified constitutive equations which can model a variety of nonlinear material phenomena observed in Rene 80 at elevated temperatures. A constitutive model was developed based on back stress and drag stress. The tensorial back stress was used to model directional effects; whereas, the scalar drag stress was used to model isotropic effects and cyclic hardening or softening. A flow equation and evolution equations for the state variables were developed in multiaxial form. Procedures were developed to generate the material parameters. The model predicted very well the monotonic tensile, cyclic, creep, and stress relaxation behavior of Rene 80 at 982 C. The model was then extended to 871, 760, and 538 C. It was shown that strain rate dependent behavior at high temperatures and strain rate independent behavior at the lower temperatures could be predicted very well. A large number of monotonic tensile, creep, stress relation, and cyclic experiments were predicted. The multiaxial capabilities of the model were verified extensively for combined tension/torsion experiments. The prediction of the model agreed very well for proportional, nonproportional, and pure shear cyclic loading conditions at 982 and 871 C.

Ramaswamy, V. G.↗

NASA NTRS1985

Constitutive modeling for isotropic materials

Constitutive theories were evaluated against a large uniaxial and multiaxial data base that was generated as part of this work. The experimental approach was to determine the constitutive behavior of Rene 80 under a multitude of conditions that are important in the design of gas turbine blades and vanes. The experimental and analytical goals of this program were successfully accomplished. A new multiaxial constitutive model which can represent the complex nonlinear high temperature behavior of Rene 80 was developed. The model was extensively verified on data at several temperatures.

Ramaswamy, V. G.↗

NASA NTRS1985

Constitutive modeling for isotropic materials

The first year of progress on a NASA-Lewis contract with the General Electric Co is documented. The purpose of this contract (NAS3-23927) is to develop and evaluate unified constitutive equations for applications to hot-path components of aircraft gas turbine engines such as high pressure turbine blades and vanes. To accomplish this goal, uniaxial, notched, and multiaxial specimens made of conventionally cast Rene 80 are being tested under conditions that simulate engine operating conditions. To reduce the raw data, automated data reduction techniques are being developed that produce computer files containing the information needed to analyze proposed constitutive theories. Described are the analytical methods being developed to determine the parameters for these nonlinear unified theories by using the reduced data files. In another activity, a dedicated finite-element computer code is being developed to use unified theories in the structural analysis of hot-section components. This code was extensively verified for one such theory by successfully predicting the strain histories measured experimentally at the notch root of complex specimens taken from complex laboratory specimens.

Ramaswamy, V. G.↗

NASA NTRS1984

Constitutive modeling for isotropic materials

The unified constitutive theories for application to typical isotropic cast nickel base supperalloys used for air-cooled turbine blades were evaluated. The specific modeling aspects evaluated were: uniaxial, monotonic, cyclic, creep, relaxation, multiaxial, notch, and thermomechanical behavior. Further development of the constitutive theories to model thermal history effects, refinement of the material test procedures, evaluation of coating effects, and verification of the models in an alternate material will be accomplished in a follow-on for this base program.

Ramaswamy, V. G.↗