Engineering topics
Polk, J. E.
Publications and source records attributed to Polk, J. E..
Design and Development of a 3 to 10 kW Ammonia Arcjet
An ammonia arcjet capable of throttling between 3 and 10 kW and producing a specific impulse of 600 s is required for the SSTAR flight experiment. Testing was performed to evaluate the performance of two nozzle configurations on ammonia arcjet performance over this power range. One of the objectives of these tests was to quantify the effect small nozzle changes have on performance. The smaller constrictor engine (2.54 mm diameter) produced a specific impulse of about 650 s over the range of 3 to 10 kW at a specific power of 60 kJ/g exceeding the 500-600 s requirement for the SSTAR flight experiment.
High Current Cathode Thermal Behavior, Part II: Theory
Cathode erosion is one of the life limiting mechanisms for several classes of electric thrusters. Since cathode erosion is strongly dependent on the cathode temperature, a quantitative understanding of the effects of cathode operation on the cathode temperature is required. The development of a cathode/plasma interaction model for determining the heat loads to the cathode as function of the various free stream plasma parameters is presented. This model is combined with a cathode thermal model in order to provide a complete and integrated picture of high current cathode operation.
Test-to-Failure of a Two-Grid, 30-cm-dia. Ion Accelerator System
To determine the failure mechanism and erosion characteristics of an ion accelerator system due to erosion by charge-exchange ions a test was performed in which a 30-cm-diameter, 2-grid ion accelerator system was tested to failure. The erosion charcteristics observed in this test, however, imply significantly shorter accelerator grid life times than typically stated in the literature. Finally, the test suggests that structural failure is probably not the most likely first failure mechanism for the accelerator grid.
Probabilistic Analysis of Ion Engine Accelerator Grid Life
The accelerator grid in two-grid ion optics systems is subject to sputter erosion by charge-exchange ions created in the ion beam.
Cyclic Endurance Test of an Ammonia Arcjet for ELITE/STAR
Explore the source record for details and available documents.
Probabilistic Analysis of 2Grind Ion Optics Failure Mechanisms
Explore the source record for details and available documents.
Ammonia arcjet engine behavior in a cyclic endurance test at 10 kW
The behavior of a 30 kWe-class ammonia arcjet operated at 10 kWe during the 707 successful cycles of an endurance test is described. The propellant flow rate was 0.170 g/s, and the measured performance was about 630 s specific impulse at an efficiency of 0.34. Data obtained indicate that the terminal voltage increased over the first 300 cycles, and then remained approximately constant for the remainder of the test, which suggests that the cathode eroded initially and then reached a stable geometry. No major changes were observed in thruster performance. The test was terminated by a series of external arcs.
Applied-field magnetoplasmadynamic engine developments
There are potential space exploration missions which may significantly benefit from the use of electric propulsion at power levels of hundreds of kilowatts. The applied magnetic field MPD thruster is potentially capable of efficient, high specific impulse operation in this power range. This paper describes current experimental and analytical efforts to further the development of such a thruster and presents the latest results. In particular, efforts to measure, simultaneously, the thrust developed by the archead and by the electromagnet, and to evaluate the effect of a diffuser on vacuum tank back pressure, are presented and discussed. It was found that with ammonia vapor as propellant, the vacuum tank pressure was reduced from 8 to 4.9 Pa at a power level of 80 kW. This pressure decrease is expected to become greater as the power and applied field are increased. Also, the development of a cathode/plasma interaction model for determining the heat loads to the cathode as functions of the various free stream plasma parameters is presented. This model is combined with a cathode thermal model in order to provide a complete and integrated picture of MPD thruster cathode operation. Several computational examples are used to illustrate the combined model.
Results of a 1462 hour ammonia arcjet endurance test
A total of 1462 hours of operaton were demonstrated in an endurance test of a 30 kWe-class ammonia arcjet operated at 10 kWe. The propellant flow rate was 0.170 g/s, and the measured performance increased from approximately 650 s specific impulse at 36 percent efficiency at the beginning of the test to 675 s at 39 percent near the end. The voltage increased and the current dropped slightly over the first 400 hours, and then remained approximately constant for the remainder of the test. The test, scheduled for 1500 hours, was terminated after an insulator in the rear of the engine failed. Post-test examination of the electrodes revealed only minimal damage. Although there was evidence of a number of mass transport processes occurring in the discharge chamber, the primary life-limiting wear mechanisms appear to be cathode tip erosion and constrictor melting.
Alkali metal propellants for MPD thrusters
Experiments performed in the United States in the 1960s and early 1970s and in the Soviet Union with alkali metal-fuelled MPD thrusters indicate performance levels substantially better than those achieved with gaseous propellants. Cathode wear appears to be less in engines with alkali metal propellants also. A critical review of the available data indicates that the data are consistent and reliable. An analysis of testing and systems-level considerations shows that pumping requirements for testing are substantially decreased and reductions in tankage fraction can be expected. In addition, while care must be exercised in handling the alkali metals, it is not prohibitively difficult or hazardous. The greatest disadvantage seems to be the potential for spacecraft contamination, but there appear to be viable strategies for minimizing the impact of propellant deposition on spacecraft surfaces. Renewed examination of alkali metal-fuelled MPD thrusters for ambitious SEI missions is recommended.
Throttling capability of a 30 kW class ammonia arcjet
The throttling capabilities of a 30 kW class ammonia arcjet and its compatibility with a breadboard power conditioning unit (PCU) were tested in two series of tests. The first series was performed to determine the performance and operating characteristics of the arcjet and the PCU over a range of power levels and propellant flow rates. The power levels for the tests were nominally between 10 and 30 kW, with some operation below 10 kW at the lower flow rates. The ammonia flow rates varied between 0.16 and 0.35 g/s. The second series of tests was an extensive investigation of operation below 12 kW using three cathode spacings. The ammonia flow rates were between 0.115 and 0.335 g/s. Operation of the arcjet from 1.5 kW up to the 30 kW design point was demonstrated with the PCU.