Engineering Papers⌕ Search

Engineering topics

Polek, T. E.

Publications and source records attributed to Polek, T. E..

6 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

A new facility and technique for two-dimensional aerodynamic testing

The design and operational characteristics of a new test leg for the High Reynolds Number Facility at Ames Research Center are presented, and the unique features of a test section for obtaining two-dimensional airfoil data are reviewed. The new facility operates at unit Reynolds numbers ranging from 1,000,000/ft to 30,000,000/ft. Boundary-layer suction panels are used in the test section (16 in. wide by 24 in. high) to minimize side-wall interference effects. Flexible, easily adjustable upper and lower walls allow test-channel area-ruling so as to nullify Mach-number changes induced by mass removal, to correct for longitudinal boundary-layer growth, and to provide contouring compatible with the streamlines of the model in free air.

Mcdevitt, J. B.↗
NASA NTRS1975

Results of investigation on an 0.015 scale configuration 140A/B space shuttle vehicle orbiter reaction control system plume-impingement model 36-0 in the NASA/Ames Research Center 3.5-foot hypersonic wind tunnel (0A83)

The results of aerodynamic pressure and wingroot bending-moment testing conducted on a 0.015-scale Configuration 140A/B space shuttle vehicle orbiter reaction control system plume-impingement model are documented. The model was investigated at nominal Mach numbers of 5.3, 7.3, and 10.3, at unit Reynolds numbers of 4,200,000 ft, 7,300,000 ft, and 1,700,000 ft. Model attitude was varied in angle of attack from 18 deg to 38 deg at angles of sideslip from -2 deg to +2 deg. The test program was conducted to establish and reaffirm incremental orbiter pressure-profile and structural-loads data due to operation of the aftbody reaction control system pitch-down engines.

Nicholas, M. E.↗
NASA NTRS1974

Results of tests OA26 and IA16 in the NASA/ARC 3.5-foot hypersonic wind tunnel on an 0.015-scale model (36-OTS) of the space shuttle configuration 140A/B to obtain pressures for venting analysis

Tests were conducted, from November 15 to December 4, 1973, to obtain surface pressure data on an 0.015-scale replica of the Space Shuttle Vehicle 4. Data were obtained at Mach numbers of 5.3, 7.4, and 10.3, to support the venting analysis for both launch and entry conditions. These tests were the final tests in a series covering a Mach number range from 0.6 to 10.3. The model was instrumented with pressure orifices in the vicinity of the cargo bay door hinge and parting lines, and on the side of the fuselage at the crew compartment, and below the orbital maneuvering system pods at the aft compartment. The model was tested at angles of attack and sideslip consistent with expected divergencies from the nominal trajectory.

Spangler, R. H.↗
NASA NTRS1972

Measurements of Reynolds analogy for a hypersonic turbulent boundary layer on a nonadiabatic flat plate.

The purpose of the described experiment was to obtain simultaneous measurements of skin friction and heat transfer at hypersonic Mach numbers, especially with conditions of considerable heat transfer. The experiment was conducted in air in the Ames Hypersonic Wind Tunnel, in which cold air was passed through an alumina storage heater system and heated to total temperatures ranging from about 670 to 1170 K. The nozzle was contoured to produce a flow at Mach 7.4. Thin-skin heat-transfer gauges were placed at equal intervals along the centerline of a sharp-edge flat plate, which was used as the model. A skin-friction balance and a boundary-layer pitot-pressure rake were mounted on each side of the centerline at a certain distance from the leading edge.

Keener, E. R.↗