Engineering Papers⌕ Search

Engineering topics

Pokhrel, Dipendra

Publications and source records attributed to Pokhrel, Dipendra.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Post‐Annealing Treatment on Hydrothermally Grown Antimony Sulfoselenide Thin Films for Efficient Solar Cells

Herein, antimony sulfoselenide (Sb 2 (S, Se) 3 ) thin‐film solar cells are fabricated by a hydrothermal method followed by a post‐deposition annealing process at different temperatures and the impact of the annealing temperature on the morphological, structural, optoelectronic, and defect properties of the hydrothermally grown Sb 2 (S, Se) 3 films is investigated. It is found that a proper annealing temperature leads to high‐quality Sb 2 (S, Se) 3 films with large crystal grains, high crystallinity, preferred crystal orientation, smooth and uniform morphology, and reduced defect density. These results show that suppressing deep‐level defects is crucial to enhance solar cell performance. After optimizing the annealing process, Sb 2 (S, Se) 3 solar cells with an improved power conversion efficiency 2.04 to 8.48% are obtained.

14 SOLAR ENERGY↗
DOE OSTI2022

Bifacial CdTe Solar Cells with Copper Chromium Oxide Back-Buffer Layer

Bifacial solar cells have the potential to maintain energy output higher than monofacial devices under unfavorable weather conditions. A transparent back-buffer layer which can passivate the interface and improve the minority carrier lifetime is critical in CdTe-based bifacial devices. Herein, solution-processed Cu x Cr y O z as a promising back-buffer for CdTe/CdS solar cells is demonstrated. The carrier lifetimes measured at the front and back of the device are 31.2 and 3.1 ns, respectively, which correspond to an increase of ≈38% and 138%, respectively, compared to the reference device. This dramatic improvement in lifetime results in a 100% increase in short-circuit current measured with backside illumination. The best bifacial device has efficiencies 7.6% and 12.5%, respectively, from back and front illumination, yielding a bifaciality factor of 0.60.

14 SOLAR ENERGY↗
DOE OSTI2021

Copper iodide nanoparticles as a hole transport layer to CdTe photovoltaics: 5.5 % efficient back-illuminated bifacial CdTe solar cells

We report the role of copper iodide (CuI) nanoparticles (NPs) as a hole transport layer (HTL) in cadmium sulfide/cadmium telluride (CdS/CdTe) photovoltaics. These CuI NPs were prepared using solution processing at room temperature and used to fabricate monofacial and bifacial CdTe solar cells with different back contacts. Using CuI/Au as the back contact, the device efficiency reached to 14.8% with outstanding fill factor (FF) of 79.2%. Replacing the gold (Au) electrode with sputtered transparent indium tin oxide (ITO), a CuI/ITO back contact yielded photoconversion efficiencies (PCEs) of 11.6% and 5.5% under front and back illumination respectively. Bifacial devices (CdTe/ITO) without the CuI NP HTL have an efficiency of 7.0% and 1.0% for front and back illumination, respectively. For CuI/ITO, a current collection of 12.0 mAcm -2 was observed upon back illumination which significantly improved over an ITO-only back contact (5.0 mAcm -2 ). The PCE obtained from back illumination was enhanced when using CuI NPs as the HTL due to the reduced back barrier height, and improved back interface as determined by temperature dependent current vs. voltage characteristics and impedance spectroscopy analysis. The improvement in device performance of the bifacial configuration is a significant step forward toward realizing thin film photovoltaic modules which harvest energy incident on the rear of the module.

36 MATERIALS SCIENCE↗