Engineering Papers⌕ Search

Engineering topics

Pipes, R. Byron

Publications and source records attributed to Pipes, R. Byron.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Investigation of the notch sensitivity of tailorable long fiber discontinuous prepreg composite laminates

Tailorable discontinuous fiber composite laminates provide relative formability beyond that of continuous fiber laminates, while achieving improved mechanical performance over comparable stochastic systems. Here, in this work, the notch sensitivity of engineered prepreg platelet molded composite (PPMC) laminates is investigated using the open-hole tension (OHT) test and compared to available data for stochastic PPMCs and continuous fiber laminates made with the same material. The press-formed thermoplastic composites (AS4/PEKK) were molded with a quasi-isotropic stacking sequence. The discontinuous PPMC laminate was found to be notch insensitive with OHT strengths ranging from 145.4 MPa (CV $=$ 7%) for d/w $=$ 0.5 to 229.3 MPa (CV $=$ 9%) for d/w $=$ 0.25. The highly ordered meso-structure of the engineered PPMC laminate yields comparatively excellent mechanical properties for relatively thin laminates in contrast to stochastic systems. Both net- and gross-section failures were observed for d/w $=$ 0.25, which suggests that the engineered PPMC laminates studied here maintain a degree of inherent, internal stress concentrations that compete with those caused by geometric features such as a circular hole. Computational simulations of the OHT tests with explicitly represented platelets were found to be in good agreement with experimental measurements. The progressive failure analysis was used to conduct a numerical investigation of the stacking sequence and platelet meso-morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Bayesian inference of fiber orientation and polymer properties in short fiber-reinforced polymer composites

Herein we present a Bayesian methodology to infer the elastic modulus of the constituent polymer and the fiber orientation state in a short-fiber reinforced polymer composite (SFRP). The properties are inversely determined using only a few experimental tests. Developing composite manufacturing digital twins for SFRP composite processes, including injection molding and extrusion deposition additive manufacturing (EDAM) requires extensive experimental material characterization. In particular, characterizing the composite mechanical properties is time consuming and therefore, micromechanics models are used to fully identify the elasticity tensor. Hence, the objective of this paper is to infer the fiber orientation and the effective polymer modulus and therefore, identify the elasticity tensor of the composite with minimal experimental tests. To that end, we develop a hierarchical Bayesian model coupled with a micromechanics model to infer the fiber orientation and the polymer elastic modulus simultaneously which we then use to estimate the composite elasticity tensor. We motivate and demonstrate the methodology for the EDAM process but the development is such that it is applicable to other SFRP composites processed via other methods. Our results demonstrate that the approach provides a reliable framework for the inference, with as few as three tensile tests, while accounting for epistemic and aleatory uncertainty. Posterior predictive checks show that the model is able to recreate the experimental data well. The ability of the Bayesian approach to calibrate the material properties and its associated uncertainties, make it a promising tool for enabling a probabilistic predictive framework for composites manufacturing digital twins.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Interlayer fusion bonding of semi-crystalline polymer composites in extrusion deposition additive manufacturing

This work focuses on the evolution of interlayer fracture toughness properties of fiber-reinforced, semi-crystalline polymers in the extrusion deposition additive manufacturing (EDAM) process. Further, this work bridges the gap between the additive process conditions (time-temperature history) and the effective layer-to-layer fracture properties developed within a printed component. This is the first step to predict delamination that can occur during printing, during cooling to room temperature after printing, and during service performance of an additively manufactured geometry. A phenomenological model is developed for fusion bonding of semi-crystalline polymer matrix composites by coupling the interdiffusion of polymer chains with the evolution of polymer crystallinity. While the interdiffusion is captured by reptation theory of polymer dynamics, the evolution of crystallinity is modeled by phenomenological crystallization kinetics and crystal melting dynamics. Further, a methodology is developed to determine the critical strain energy release rate, G IC of the interlayer interface and experiments are conducted utilizing the double cantilever beam fracture test geometry. In conclusion, predictions of GIC as a function of thermal history are compared with experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A machine learning approach to determine the elastic properties of printed fiber-reinforced polymers

This work focuses on the simultaneous determination of the elastic constants and the fiber orientation state for a short fiber-reinforced polymer composite by performing a minimum of experimental tests. Here we introduce a methodology that enables the inverse determination of fiber orientation state and the in-situ polymer properties by performing tensile tests at the composite coupon level. We demonstrate the approach for the extrusion deposition additive manufacturing (EDAM) process to illustrate one application of the methodology, but the development is such that it can be applied to short fiber-reinforced polymer (SFRP) systems processed via other methods. Currently, developing composites additive manufacturing digital twins require extensive material characterization. In particular, the mechanical characterization of the orthotropic elastic properties of a composite involves extensive sample preparation and testing, therefore the elasticity tensor is generally populated using a micromechanics model. This, however, requires measuring the fiber orientation state in addition to knowing the constituent material properties. Experimentally measuring the fiber orientation state can be tedious and time consuming. Further, optical methods are limited to resolving the orientation of cylindrical fibers or cluster of non-cylindrical fibers, and computed tomography (CT) methods scan regions of volume that are much smaller than a full printed bead. Therefore, we propose a methodology, accelerated by machine learning, to identify the anisotropic mechanical properties and fiber orientation state at the same time. Early results show that inference of the fiber orientation and composite properties is possible with as few as three tensile tests. Our results show that a combination of the choice of the micromechanics model and reliable set of experiments can yield the nine elastic constants, as well as, the fiber orientation state.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of Fiber Orientation on Deformation of Additive Manufactured Composites

Anisotropy caused by flow-induced fiber orientation of discontinuous fibers within the extrudate in the Extrusion Deposition Additive Manufacturing (EDAM) process gives rise to anisotropic shrinkage in printed parts and thereby, final part deformations. Three fiber orientation states, described by the second-order orientation tensor, were investigated to determine their influence upon final geometry. Two material systems were investigated including a short glass fiber-reinforced polyamide and a short carbon fiber-reinforced polyamide. A curvilinear geometry was modeled and printed virtually in the thermo-mechanical simulation, ADDITIVE3D©. The scale of the printed geometry was in the range of 300–400 mm and contained three semicircular geometry regions connected to linear regions, thereby inducing significant magnification of the spring-in deformation. The predicted deformation of the printed geometry for the three fiber orientation states and two material systems were compared. The deformation predicted for glass fiber-filled polyamide and carbon fiber-filled polyamide of the same fiber orientation states showed comparable deformations. In conclusion, the largest residual deformation was shown to correspond to the orientation tensor with the greatest degree of anisotropy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ characterization of residual stress evolution during heat treatment of SiC/SiC ceramic matrix composites using high-energy X-ray diffraction

Volumetric strains were measured in silicon carbide/silicon carbide melt-infiltrated ceramic matrix composites (CMCs) at ambient and high temperatures using high-energy synchrotron X-ray diffraction (XRD). Both silicon and silicon carbide constituents were interrogated utilizing a broad spectrum of diffracting planes that would be largely inaccessible to common laboratory XRD equipment. Residual room-temperature principal strains in the melt-infiltrated silicon phase were found to be approximately 1100 mu epsilon in compression, corresponding to stresses of approximately 300 MPa using simplifying constitutive assumptions. Residual room-temperature principal strains in silicon carbide particles found throughout the matrix were approximately 500 mu epsilon in tension, corresponding to approximately 300 MPa. Residual strains were found to decrease considerably as temperatures increased from ambient temperature to 1250 degrees C. Additionally, residual strains returned to approximately preheat treatment values after cool-down to ambient temperature. Strain measurements in the silicon phase were found to be significantly affected by dissolved boron dopant levels causing contraction of the silicon lattice. This contraction must be accounted for in high-temperature experiments for accurate calculation of stresses in the silicon phase.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A numerical study of the meso-structure variability in the compaction process of prepreg platelet molded composites

Compaction deformations in a thermoplastic composite system molded from chopped prepreg platelets were analyzed to obtain statistical distributions of local distortions that define the final consolidated meso-structure. This study provides an insight into and allows quantification of the intrinsic geometric variability of the composite meso-structure that controls the variability of the effective composite mechanical properties. A two-phase viscoelastic finite element model was utilized to treat the behavior of molten prepreg platelets, which were assumed to be incompressible and inextensible in the fiber direction during processing. A two-step simulation procedure with discretely modeled platelets and platelet-to-platelet contacts is proposed. The analysis begins with a drop simulation of the uncontrolled material deposition followed by a 3D finite element analysis of the preform compaction and bulk material flow. The proposed model provides a method for generating a composite meso-structure ab initio starting from a statistical sampling of the initial conditions for platelet deposition. The predicted platelet thickness distribution, intra-platelet fiber waviness and out-of-plane platelet undulations were found to be in good agreement with experimental measurements. An estimate of the volume of resin pockets was inferred from the compaction simulation.

36 MATERIALS SCIENCE↗
NASA NTRS2019

Structural Framework for Flight I: NASA’s Role in Development of Advanced Composite Materials for Aircraft and Space Structures

This monograph is organized to look at: the successful application of composites on aircraft and space launch vehicles, the role of NASA in enabling these applications for each different class of flight vehicles, and a discussion of the major advancements made in discipline areas of research. In each section, key personnel and selected references are included. These references are intended to provide additional information for technical specialists and others who desire a more in-depth discussion of the contributions. Also in each section, lessons learned and future challenges are highlighted to help guide technical personnel either in the conduct or management of current and future research projects related to advanced composite materials.

Tenney, Darrel R.↗
NASA NTRS2011

Structural Framework for Flight: NASA's Role in Development of Advanced Composite Materials for Aircraft and Space Structures

This serves as a source of collated information on Composite Research over the past four decades at NASA Langley Research Center, and is a key reference for readers wishing to grasp the underlying principles and challenges associated with developing and applying advanced composite materials to new aerospace vehicle concepts. Second, it identifies the major obstacles encountered in developing and applying composites on advanced flight vehicles, as well as lessons learned in overcoming these obstacles. Third, it points out current barriers and challenges to further application of composites on future vehicles. This is extremely valuable for steering research in the future, when new breakthroughs in materials or processing science may eliminate/minimize some of the barriers that have traditionally blocked the expanded application of composite to new structural or revolutionary vehicle concepts. Finally, a review of past work and identification of future challenges will hopefully inspire new research opportunities and development of revolutionary materials and structural concepts to revolutionize future flight vehicles.

Tenney, Darrel R.↗
NASA NTRS2009

NASA Composite Materials Development: Lessons Learned and Future Challenges

Composite materials have emerged as the materials of choice for increasing the performance and reducing the weight and cost of military, general aviation, and transport aircraft and space launch vehicles. Major advancements have been made in the ability to design, fabricate, and analyze large complex aerospace structures. The recent efforts by Boeing and Airbus to incorporate composite into primary load carrying structures of large commercial transports and to certify the airworthiness of these structures is evidence of the significant advancements made in understanding and use of these materials in real world aircraft. NASA has been engaged in research on composites since the late 1960 s and has worked to address many development issues with these materials in an effort to ensure safety, improve performance, and improve affordability of air travel for the public good. This research has ranged from synthesis of advanced resin chemistries to development of mathematical analyses tools to reliably predict the response of built-up structures under combined load conditions. The lessons learned from this research are highlighted with specific examples to illustrate the problems encountered and solutions to these problems. Examples include specific technologies related to environmental effects, processing science, fabrication technologies, nondestructive inspection, damage tolerance, micromechanics, structural mechanics, and residual life prediction. The current state of the technology is reviewed and key issues requiring additional research identified. Also, grand challenges to be solved for expanded use of composites in aero structures are identified.

Tenney, Darrel R.↗
NASA NTRS2002

Cyber Technology for Materials and Structures in Aeronautics and Aerospace

The evolution of composites applications in aeronautics from 1970 to the present is discussed. The barriers and challenges to economic application and to certification are presented and recommendations for accelerated development are outlined. The potential benefits of emerging technologies to aeronautics and their foundation in composite materials are described and the resulting benefits in vehicle take off gross weight are quantified. Finally, a 21st century vision for aeronautics in which human mobility is increased by an order of magnitude is articulated.

Pipes, R. Byron↗
NASA NTRS2002

Dimensional Stability of Complex Shapes Manufactured by the VARTM Process

The vacuum assisted resin transfer molding (VARTM) process is a cost effective, innovative method that is being considered for manufacture of large aircraft-quality components where high mechanical properties and dimensional tolerance are essential. In the present work, carbon fiber SAERTEX fabric/SI-ZG-5A epoxy resin C-shaped laminates were manufactured by VARTM using different cure cycles followed by the same post-cure cycle. The final part thickness was uniform except at the corner were thinning was observed. The cure cycle selected is shown to significantly affect the part spring-in and a long cycle at 66 C followed by a 178 C post-cure produced a part with negligible spring-in.

Hubert, Pascal↗
NASA NTRS2002

Variability Analysis in Vacuum Assisted Resin Transfer Molding

The vacuum assisted resin transfer molding (VARTM) process is a low-cost, innovative method that is being considered for manufacture of large aircraft-quality components where high mechanical properties and dimensional tolerance are essential. In the present work a rigorous science-based approach is used to study the VARTM processing of high performance complex shape components. A process model, COMPRO, is used to simulate the cure of panels produced by VARTM. It was found that the presence of the distribution media significantly affects the magnitude of the exotherm particularly for thick panels. For C-shaped laminates, the part distortion was a function of fiber volume fraction distribution and was affected by the presence of the distribution media.

Hubert, Pascal↗
NASA NTRS2001

Automated Fiber Placement of PEEK/IM7 Composites with Film Interleaf Layers

The incorporation of thin discrete layers of resin between plies (interleafing) has been shown to improve fatigue and impact properties of structural composite materials. Furthermore, interleafing could be used to increase the barrier properties of composites used as structural materials for cryogenic propellant storage. In this work, robotic heated-head tape placement of PEEK/IM7 composites containing a PEEK polymer film interleaf was investigated. These experiments were carried out at the NASA Langley Research Center automated fiber placement facility. Using the robotic equipment, an optimal fabrication process was developed for the composite without the interleaf. Preliminary interleaf processing trials indicated that a two-stage process was necessary; the film had to be tacked to the partially-placed laminate then fully melted in a separate operation. Screening experiments determined the relative influence of the various robotic process variables on the peel strength of the film-composite interface. Optimization studies were performed in which peel specimens were fabricated at various compaction loads and roller temperatures at each of three film melt processing rates. The resulting data were fitted with quadratic response surfaces. Additional specimens were fabricated at placement parameters predicted by the response surface models to yield high peel strength in an attempt to gage the accuracy of the predicted response and assess the repeatability of the process. The overall results indicate that quality PEEK/lM7 laminates having film interleaves can be successfully and repeatability fabricated by heated head automated fiber placement.

Hulcher, A. Bruce↗
NASA NTRS2001

Flow and Compaction During the Vacuum Assisted Resin Transfer Molding Process

The flow of an epoxy resin and compaction behavior of carbon fiber preform during vacuum- assisted resin transfer molding (VARTM) infiltration was measured using an instrumented tool. Composite panels were fabricated by the VARTM process using SAERTEX(R)2 multi-axial non- crimp carbon fiber fabric and the A.T.A.R.D. SI-ZG-5A epoxy resin. Resin pressure and preform thickness variation was measured during infiltration. The effects of the resin on the compaction behavior of the preform were measured. The local preform compaction during the infiltration is a combination of wetting and spring-back deformations. Flow front position computed by the 3DINFIL model was compared with the experimental data.

Grimsley, Brian W.↗
NASA NTRS1999

Cyber Technology for Materials and Structures in Aeronautics and Aerospace

This report summarizes efforts undertaken during the 1998-99 program year and includes a survey of the field of computational mechanics, a discussion of biomimetics and intelligent simulation, a survey of the field of biomimetics, an illustration of biomimetics and computational mechanics through the example of the high performance composite tensile structure. In addition, the preliminary results of a state-of-the art survey of composite materials technology is presented.

Pipes, R. Byron↗
NASA NTRS1994

Advanced composites in Japan

The JTEC Panel on Advanced Composites surveyed the status and future directions of Japanese high-performance ceramic and carbon fibers and their composites in metal, intermetallic, ceramic, and carbon matrices. Because of a strong carbon and fiber industry, Japan is the leader in carbon fiber technology. Japan has initiated an oxidation-resistant carbon/carbon composite program. With its outstanding technical base in carbon technology, Japan should be able to match present technology in the U.S. and introduce lower-cost manufacturing methods. However, the panel did not see any innovative approaches to oxidation protection. Ceramic and especially intermetallic matrix composites were not yet receiving much attention at the time of the panel's visit. There was a high level of monolithic ceramic research and development activity. High temperature monolithic intermetallic research was just starting, but notable products in titanium aluminides had already appeared. Matrixless ceramic composites was one novel approach noted. Technologies for high temperature composites fabrication existed, but large numbers of panels or parts had not been produced. The Japanese have selected aerospace as an important future industry. Because materials are an enabling technology for a strong aerospace industry, Japan initiated an ambitious long-term program to develop high temperature composites. Although just starting, its progress should be closely monitored in the U.S.

Diefendorf, R. Judd↗