Engineering Papers⌕ Search

Engineering topics

Pines, D.

Publications and source records attributed to Pines, D..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Performance Verification Report, METSAT (S/N:107) AMSU-A1 Receiver Assemblies: P/N 1356429-1, S/N:F04, P/N 1356409-1,S/N F04

This is the Performance Verification Report, METSAT (S/N: 107) AMSU-A1 Receiver Assemblies, P/N 1356429-1, SIN: F04, P/N 1356409- 1, S/N: F04, for the Integrated Advanced Microwave Sounding Unit-A (AMSU-A). The AMSU-A receiver subsystem comprises two separated receiver assemblies; AMSU-A1 and AMSU-A2 (P/N 1356441-1). The AMSU-A1 receiver contains 13 channels and the AMSU-A2 receiver 2 channels. The AMSU-A receiver assembly is further divided into two parts; AMSU-A I - I (P/N 13 5 6429- 1) and AMSU-A 1 -2 (P/N 1356409-1), which contain 9 and 4 channels, respectively. The AMSU-A receiver subsystem is located in between the antenna and signal processing subsystems of the AMSU-A instrument and comprises the RF and IF components from isolators to attenuators. It receives the RF signals from the antenna subsystem, down-converts the RF signals to IF signals, amplifies and defines the IF signals to proper power level and frequency bandwidth as specified for each channel, and inputs the IF signals to the signal processing subsystem. The test reports for the METSAT AMSU-A receiver subsystem are prepared separately for Al and A2 receivers so that each receiver stands alone during integration of instruments into the spacecraft. This test report presents the test data of the N4ETSAT AMSU-A1 Flight Model No. 4 (FM-4) receiver subsystem. The tests are performed per the Acceptance Test Procedure (ATP) for the AMSU-A Receiver Subsystem, AE-26002/6A. The functional performance tests are conducted either at the component or subsystem level. While the component-level tests are performed over the entire operating temperature range predicted by thermal analysis, most subsystem-level tests are conducted at ambient temperature only. Key performances (bandpass characteristics and noise figure) of the receiver subsystem are verified over the operating temperature.

Pines, D.↗
NASA NTRS1998

Integrated Advanced Microwave Sounding Unit-A(AMSU-A). Performance Verification Report, METSAT Phase Locked Oscillator Assembly, P/N 1348360-1, S/N's F07 and F08

Two Flight Model AMSU-A Phase Locked Oscillators (PIN 1348360-1, S/N F07 and F08) have been tested per AES Test Procedure AE-26758 Rev. B, which include full functional testing, vibration testing, thermal testing, and AM/FM Noise testing. Both assemblies satisfactorily passed all performance requirements of the AE-26633 Product Specification. During the thermal cycling of both units, spurs developed 1 MHz from the carrier when the units were cold, and TARs were written to document the anomaly. The symptoms observed in both cases were consistent with inadequate tuning. The units were successfully re-tuned. In the case of F08, re-tuning required a design change which allowed a greater range of possible values for tuning resisters. Both units completed thermal cycling without further delay. The results of the required tests are presented in the following section as test data. As indicated on the test data sheets, all measured data passed all requirements.

Pines, D.↗
NASA NTRS1998

Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Performance Verification Report: METSAT Phase Locked Oscillator Assembly, P/N 1334360-1, S/N's F03 and F04

Two Flight Model AMSU-A Phase Locked Oscillators (P/N 1348360-1, S/Ns F03 and F04) have been tested per AES Test Procedure AE-26758. The tests included vibration testing, thermal cycle testing, AM/FM Noise testing, and full functional testing. EMI/REO 2 Testing was not performed. (See test data for S/N F01). Both AMSU-A Phase Locked Oscillators satisfactorily passed all performance requirements of the AE-26633 Product specification. During thermal cycling of PLO serial number F03, the oven and data logger momentarily lost power, including a loss of data. The unit did not experience any thermal stress. TAR 003134 describes the corrective action. Prior to testing PLO serial number FO4, power was applied to the unit. (+15v,-15v) the unit did not display the proper phase lock. Upon test equipment check out a connector was found to be defective. TAR 003133 describes the corrective action. After completion of testing of PLO serial number F04 was installed into Receiver Assembly F02. Upon testing F02 Receiver Assembly the unit was found not to phase lock at ambient temperature. Removal of PLO Assembly F04 was required. R2 was the real issue. Solithane was secondary. Troubleshooting revealed excessive solithane on inner PLL Assembly cover inhibiting optimum grounding. Also, R2 was reselected which increased the lock range from -30 C to +60 C. TAR 002737 describes the corrective action.

Pines, D.↗
NASA NTRS1993

Quasiparticle Interactions in Neutron Matter for Applications in Neutron Stars

A microscopic model for the quasiparticle interaction in neutron matter is presented. Both-particle (pp) and particle-hole (ph) correlations are included. The pp correlations are treated in semi-empirical way, while ph correlations are incorporated by solving coupled two-body equations for particle-hole interaction and the scattering amplitude of the Fermi sphere. The resulting integral equations self-consistently sum the ph reducible diagrams. Antisymmetry is kept at all stages and hence the forward-scattering sum rules for the scattering amplitude are obeyed. Results for Landau parameters and transport coefficients in a density regime representing the crust of a neutron star are presented. We also estimate the (1)S(sub 0) gap parameter for neutron superfluidity and comment briefly on neutron-star implications.

Wambach, J↗
NASA NTRS1993

Quasiparticle Interactions in Neutron Matter for Applications in Neutron Stars

A microscopic model for the quaisiparticle interaction in neutron matter is presented. Both particle-particle (pp) and particle-hole (ph) correlation are are included. The pp correlations are treated in semi-empirical way, while ph correlations are incorporated by solving coupled two-body equations for the particle hole interaction and the scattering amplitude on the Fermi sphere. The resulting integral equations self-consistently sum the ph reducible diagrams. Antisymmetry is kept at all stages and hence the forward-scattering sum rules are obeyed. Results for Landau parameters and transport coefficients in a density regime representing the crust of a neutron star are presented. We also estimate the S-1 gap parameter for neutron superfluidity and comment briefly on neutron-star implications.

Wambach, J.↗
NASA NTRS1989

Vortex creep and the internal temperature of neutron stars - Linear and nonlinear response to a glitch

The dynamics of pinned superfluid in neutron stars is determined by the thermal 'creep' of vortices. Vortex creep can respond to changes in the rotation rate of the neutron star crust and provide the observed types of dynamical relaxation following pulsar glitches. It also gives rise to energy dissipation, which determines the thermal evolution of pulsars once the initial heat content has been radiated away. The different possible regimes of vortex creep are explored, and it is shown that the nature of the dynamical response of the pinned superfluid evolves with a pulsar's age. Younger pulsars display a linear regime, where the response is linear in the initial perturbation and is a simple exponential relaxation as a function of time. A nonliner response, with a characteristic nonlinear dependence on the initial perturbation, is responsible for energy dissipation and becomes the predominant mode of response as the pulsar ages. The transition from the linear to the nonlinear regime depends sensitively on the temperature of the neutron star interior. A preliminary review of existing postglitch observations is given within this general evolutionary framework.

Alpar, M. A.↗
NASA NTRS1988

Spontaneous superfluid unpinning and the inhomogeneous distribution of vortex lines in neutron stars

The equation of motion of the pinned superfluid which couples to the crust of neutron stars via thermal vortex creep is studied. Spontaneous unpinning at locations characterized by a very inhomogeneous distribution of vortex lines is examined as a possible mechanism for the initiation of glitches. It is suggested that structural inhomogeneities in the crust of neutron stars may be responsible for frequent microglitches which lead to pulsar timing noise. A generalization of the model shows promise for explaining the origin of the giant glitches in pulsars.

Cheng, K. S.↗
NASA NTRS1987

A search for X-ray emission from a nearby pulsar - PSR 1929 + 10

Observations of the radio pulsar PSR 1929 + 10 with the Exosat observatory are reported. A 2 sigma upper limit of 0.0005 cts/s was obtained in the 0.04-2.4 keV range, which translates into a luminosity upper limit of 2 x 10 to the 29th erg/s for a power-law source with photon number index 1-3, and a luminosity upper limit of 10 to the 30th erg/s corresponding to a temperature of 190,000 K for a blackbody with radius 10 km. The implications of these upper limits for various models and their compatibility with the positive detection of this source by the Einstein Observatory are discussed.

Alpar, A.↗
NASA NTRS1985

Superfluidity in neutron stars

Astrophysical evidence is reviewed for the existence of at least three distinct superfluids inside neutron stars from the observed relaxation of the rotation and spin-down rates of the pulsars Vela, Crab, and PSR0525 + 21, following sudden jumps or glitches in these quantities. Theoretical aspects of neutron and proton superfluids in neutron stars and core neutron communication, glitches and post-glitch relaxation, neutron star coupling, and vortex creep theory are discussed. The effects of the superfluid interior in the accreting neutron star X-ray sources are also considered.

Pines, D.↗
NASA NTRS1985

Neutron stars as cosmic hadron physics laboratories

Extensive observations of Her-1 with the Exosat satellite have led to a new understanding of both the dynamics of neutron-star superfluids and the free precession of neutron stars. Detailed microscopic calculations on neutron matter and the properties of the pinned crustal superfluid are provided to serve as a basis for comparing theory with observation on neutron stars. Topics discussed include the Hadron matter equation of state, neutron star structure, Hadron superfluids, the vortex creep theory, Vela pulsar glitches, astrophysical constraints on neutron matter energy gaps, the 35 day periodicity of Her-1, and the neutron matter equation of state. It is concluded that since the post-glitch fits and the identification of the 35th periodicity in Her X-1 as stellar wobble require a rigid neutron matter equation of state, the astrophysical evidence for such an equation seems strong, as well as that for an intermediate Delta(rho) curve.

Pines, D.↗
NASA NTRS1985

Gravitational radiation from a solid-crust neutron star

The relationship between the rapid rotation of the millisecond pulsar and gravitational radiation is addressed. By balancing gravitational radiation against the rate of rotational energy loss, it is found that if the effective triaxiality exceeds about 10 to the -9th, gravitational radiation alone would spin a millisecond pulsar down at a faster rate than the observed period derivative. It is shown that the effective triaxiality is much less than the maximum triaxiality, so that gravitational radiation is not likely to play a major role in the evolution of millisecond pulsars even in the absence of damping. Damping times for precession of the solid crust are estimated to be less than 2000 years.

Alpar, M. A.↗
NASA NTRS1985

Vortex creep and the internal temperature of neutron stars The Crab pulsar and PSR 0525 + 21

The behavior of the Crab pulsar following the 1969 and 1975 glitches and the postglich behavior of the old pulsar PSR 0525 + 21 are explained as resulting from internal torques due to the thermal creep of vortex lines in pinned superfluid regions. An overview of vortex creep theory is first given, and the immediate postglitch behavior of the Crab pulsar is calculated and compared with observation. The persistent shift in the spin-down rate observed for the Crab pulsar following the 1975 glitch is considered, and the internal and surface temperatures of this pulsar are deduced. The postglich behavior expected for very old pulsars is examined, showing that PSR 0525 + 21 falls into this category. It is concluded that the behavior of the Crab pulsar following both glitches can be characterized by the same two pinning regions. A comparison of the internal temperature for the Crab and Vela pulsars provides a significant constraint on the cooling of neutron stars.

Alpar, M. A.↗
NASA NTRS1984

Gravitational radiation from a solid crust neutron star

A rapidly rotating neutron star with a solid crust will have a rotationally induced oblateness that is constrained by the rigidity of the solid. It is shown that the effective triaxiality and the gravitational radiation output are small, in agreement with the very small change in period of PSR 1937 + 21.

Ali Alpar, M.↗
NASA NTRS1984

Superfluidity in millisecond pulsars

The evidence for superfluidity in the Vela pulsar, the Crab pulsar and PSR 0525 + 21 is reviewed, and the prospects for observing similar consequences of superfluidity in the already-discovered millisecond pulsars are examined. Inter alia, the likelihood of observing glitches, the expected postglitch behavior, and pulsar heating by energy dissipation due to the creep of neutron vortex lines in pinned superfluid regions of the crust are considered.

Pines, D.↗
NASA NTRS1984

Vortex creep and the internal temperature of neutron stars. II - Vela pulsar

The observed complex postglitch behavior of the Vela pulsar is explained as resulting from coupling of the crust to crustal neutron superfluid, specifically that part of the superfluid in which vortex lines are pinned to crustal nuclei. It is shown how the general theory of vortex creep provides an excellent fit to the timing observations of Downs which span the decade 1969-1979 and include four giant glitches. Relaxation times, inertial moments, and limits on superfluid pinning parameters are extracted for three distinct regions of vortex pinning in the star, with results which are consistent with microscopic theories of its internal structure. Relaxation times due to vortex creep are directly proportional to the internal temperature of the star, so that the limits obtained for pinning parameters translate to bounds on this temperature. It is concluded that the internal temperature of the Vela pulsar is about 10-million K and discuss the extent to which improved calculations of vortex pinning as well as soft X-ray observations of other stars will make possible an improved determination of the pulsar temperature.

Alpar, M. A.↗
NASA NTRS1984

Vortex creep and the internal temperature of neutron stars. I - General theory

The theory of a neutron star superfluid coupled to normal matter via thermal creep against pinning forces is developed in some detail. General equations of motion for a pinned rotating superfluid and their form for vortex creep are given. Steady state creep and the way in which the system approaches the steady state are discussed. The developed formalism is applied to the postglitch relaxation of a pulsar, and detailed models are developed which permit explicit calculation of the postglitch response. The energy dissipation associated with creep and glitches is considered.

Alpar, M. A.↗
NASA NTRS1981

Giant glitches and pinned vorticity in the Vela and other pulsars

Previously unexamined regularities in the Vela pulsar timing data are noted, and explained by a theory of giant glitches in the Vela and other pulsars as the dynamic consequence of catastrophic unpinning events in the pinned crustal neutron superfluid. Postglitch behavior then results from the glitch-induced vortex creep. An implication of the theory is that the energy release in this glitch scenario need not appear instantaneously on the surface as heat.

Alpar, M. A.↗