Engineering topics

Phillips, William H.

Publications and source records attributed to Phillips, William H..

6 records

NASA NTRS1990

Determination of the Pressure Drag of Airfoils by Integration of Surface Pressures

A study was conducted of the causes of pressure drag of subsonic airfoils. In a previous paper by the author, the pressure drag is obtained by calculating the total drag from the momentum defect in the boundary layer at the trailing edge and subtracting the friction drag obtained from integration of surface friction along the chord. Herein, the pressure drag is obtained by integrating the streamwise components of surface pressure around the airfoil. Studies were made to verify the accuracy of the integration procedure. The values of pressure drag were much smaller than those obtained by the previous method. This lack of agreement is attributed to the difficulty of calculating boundary layer conditions in the vicinity of the trailing edge and to the extreme sensitivity of the circulation and lift to the trailing edge conditions. The results of these studies are compared with those of previous investigations.

Phillips, William H.↗

NASA NTRS1988

Flying qualities from early airplanes to the Space Shuttle

This paper discusses the historical development of the study of flying qualities and the evolution of flying qualities requirements. Subjects considered include the scope of flying qualities, early historical development of flying qualities, research on flying qualities requirements, human response characteristics, command control systems, gust response and its relation to flying qualities, prediction of flying qualities, discussion of the Space Shuttle and of some recent airplanes, and format of the flying qualities requirements.

Phillips, William H.↗

NASA NTRS1988

Studies of friction drag and pressure drag of airfoils using the Eppler program

Most previous studies of the drag and two-dimensional airfoils consider only the total drag. The present report gives results of a study of three airfoils, using the Eppler program, to determine the distribution of friction drag along the chord and to obtain relative values of friction drag and pressure drag over a wide range of angle of attack and Reynolds number. The effects of boundary-layer suction in the turbulent region of the boundary layer of two of the airfoils are also investigated. The pressure drag is found to be an important component of the total drag, reaching values of 60 to 80 percent of the total drag near the stall. The use of suction producing a uniform inflow in the turbulent region of the boundary layer results in large increases in maximum lift, and increases the skin-friction drag but reduces or even changes the sign of the pressure drag.

Phillips, William H.↗

NASA NTRS1961

Analysis of Effects of Interceptor Roll Performance and Maneuverability on Success of Collision-Course Attack

An attempt has been made to determine the importance of rolling performance and other factors in the design of an interceptor which uses collision-course tactics. A graphical method is presented for simple visualization of attack situations. By means of diagrams showing vectoring limits, that is, the ranges of interceptor position and heading from which attacks may be successfully completed, the relative importance of rolling performance and normal-acceleration capability in determining the success of attacks is illustrated. The results indicate that the reduction in success of attacks due to reduced rolling performance (within the limits generally acceptable from the pilots' standpoint) is very small, whereas the benefits due to substantially increasing the normal-acceleration capability are large. Additional brief analyses show that the optimum speed for initiating a head-on attack is often that corresponding to the upper left-hand corner of the V-g diagram. In these cases, increasing speed beyond this point for given values of normal acceleration and radar range rapidly decreases the width of the region from which successful attacks can be initiated. On the other hand, if the radar range is increased with a variation somewhere between the first and second power of the interceptor speed, the linear dimensions of the region from which successful attacks can be initiated vary as the square of the interceptor speed.

Phillips, William H.↗

NASA NTRS1942

Comparison of Aileron Control Characteristics as Determined in Flight Tests of P-36, P-40, Spitfire, and Hurricane Pursuit Airplanes

The Army Air Force has made available several pursuit-type airplanes for quantitative investigation of their flying and handling qualities. One Item of special interest obtained from the results of the investigation is a comparison of the aileron control characteristics of the P-36, P-40, Hawker Hurricane, and Supermarine Spitfire airplanes. Figure 1 shows the design characteristics of the ailerons and the control sticks of the four airplanes. Aileron effectiveness may be expressed in terms of the helix angle generated by the wing tip in a steady roll. This angle is given by the expression pb/2V, where p is the rolling velocity, b the wing span, and V the true airspeed, expressed in consistent units. This quantity is convenient to use because, although it does not rep resent directly the rolling velocity of airplanes of different spans or airplanes operating at different speeds, it provides a satisfactory basis for computing the rate of roll and the time required to bank a given amount under any given set of conditions. The ratio of pb/2V obtained in any roll to the maximum value reached with full aileron deflection indicates the fraction of the maximum aileron travel that was reached. A complete discussion of this criterion for aileron effectiveness is given in reference 1. The aileron effectiveness of the various airplanes is compared in the following table on the basis of the response obtained with stick forces of 30 and 5 pounds. A force of 30 pounds is somewhat less than the greatest stick force exerted by the pilot. Repeated flight measurements have shown, however, that this force is a reasonable upper limit for maneuvering at high speeds.

Phillips, William H.↗

NASA NTRS1942

Control-Surface Instability on High-Speed Airplanes

Tests of several modern airplanes indicate that control surfaces with a high degree of aerodynamic balance are likely to possess characteristics which make them unsatisfactory or dangerous in high-speed flight. Dive tests made in the spring of 1940 at the NACA on a naval fighter-type airplane illustrate one form of instability that may be encountered. During a dive at an indicated airspeed of 365 miles per hour, the ailerons suddenly overbalanced. The efforts of the pilot to bring the ailerons back to neutral resulted in a violent oscillation of the control stick from side to side. Fortunately, the force required to return the ailerons to neutral was within the pilot's capabilities. A time history of the maneuver is given in figure1 and typical frames from motion pictures of the cockpit and of the wing, taken during the maneuver, are given in figure 2. In the illustrated case, the occurrence of aerodynamic overbalance was attributed to a slight bulge, approximately 1/16 inch thick, on the lower surface of the leading edges of the ailerons, caused by the installation of additional mass balance ahead of the hinge line. A drawing showing the shape of the bulge is given in figure 3. After this slight protuberance had been eliminated, dives were successfully made at higher speeds.

Phillips, William H.↗