Engineering Papers⌕ Search

Engineering topics

Phillips, W. P.

Publications and source records attributed to Phillips, W. P..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Subsonic-to-Hypersonic Aerodynamic Characteristics for a Winged, Circular-Body, Single-Stage-to-Orbit Spacecraft Configuration

Experimental aerodynamic characteristics were obtained for a generic, winged, circular-body, single-stage-to-orbit spacecraft configuration. The baseline configuration was longitudinally stable and trimmable at almost all Mach numbers from 0.15 to 10.0--with the exception occurring at low supersonic speeds. Landing speed and subsonic-to-hypersonic longitudinal stability and control appear to be within design guidelines. Lateral-directional instabilities found over the entire speed range, however, create a problem area for this configuration. Longitudinal aerodynamic predictions made utilizing the Aerodynamic Preliminary Analysis System (APAS) were in qualitative, often quantitative agreement with experimental values.

Phillips, W. P.↗
NASA NTRS1993

Hypersonic aerodynamic characteristics for Langley Test Technique Demonstrator

Experimental longitudinal and lateral-directional aerodynamic characteristics were obtained for a generic transatmospheric vehicle concept referred to as the Langley Test Technique Demonstrator. The baseline configuration, without engine modules, was longitudinally and directionally unstable over the hypersonic Mach number range of the investigation and exhibited untrimmed (L/D)max levels between 2.6 and 2.8. Adding various engine modules to the baseline configuration produced mainly, degradations in lift-to-drag ratio. In general, longitudinal aerodynamic coefficients predicted with an engineering code referred to as Aerodynamic Preliminary Analysis System (APAS) were in qualitative, and often quantitative agreement with measurement.

Phillips, W. P.↗
NASA NTRS1991

Super/hypersonic aerodynamic characteristics for a transatmospheric vehicle concept having a minimum drag forebody

Experimental longitudinal and lateral-directional aerodynamic characteristics were obtained for a generic transatmospheric vehicle concept having a replaceable minimum drag forebody shape. The alternate forebody tested was a 1/4-power series body. Tests were made over a range of Mach numbers from 2 to 10 at a nominal Reynolds number, based on a length of 2.3 x 10 to the 8th and angles of attack from -4 to 20 deg. The minimum drag forebody provided significant improvements in minimum drag and L/D for the configuration as well as a longitudinally stabilizing increment. Although the baseline configuration is longitudinally unstable, the L/D improvements at low to moderate angles of attack would enhance cruise performance. Varying wing incidence angles was demonstrated as an effective horizontal trim device without significant trim drag penalties.

Phillips, W. P.↗
NASA NTRS1986

Bailout from the Space Shuttle

Studies to investigate the bailout characteristics from the Space Shuttle Orbiter at low-subsonic speeds have been made in the Langley 12-foot Low-Speed Tunnel and the Langley 4- by 7Meter Tunnel with 0.03-scale models. The effect of crew-model exit velocity, body posture, and body weight were studied with egress from the Orbiter main side hatch and from the upper cabin hatch. Force tests were made to determine the high angle-of-attack trim characteristics of the Orbiter in an attempt to improve bailout conditions. A computer simulation was made to evaluate the maneuver necessary to attain the high-angle trim.

Ware, G. M.↗
NASA NTRS1985

Space Shuttle orbiter trimmed center-of-gravity extension study

Aerodynamic, heat transfer, and system design studies to determine removable modifications for the Space Shuttle orbiter that would extend its forward center-of-gravity triom capability are summarized. Wind-tunnel tests were conducted at Mach numbers ranging from 0.25 to 20.3 to determine the most effective aerodynamic modifications. Heat transfer and system design studies determined the impact of the modifications on the thermal protection system and structural weight of the vehicle. The most effective modifications were in-fillet canards or a forward extension of the existing forward wing fillet.

Scallion, W. I.↗
NASA NTRS1985

Study of several factors affecting crew escape trajectories from the Space Shuttle Orbiter at low-subsonic speeds

Factors affecting the bailout characteristics from the space shuttle orbiter at low-subsonic speeds were investigated. In the 12-foot low-speed tunnel and the 4 by 7-meter tunnel with 0.03-scale models. The effect of crew-model exit velocity, body position, and body weight were studied with egress from the main side hatch with the orbiter upright and from the upper cabin hatch with the orbiter inverted. Crew model drag and flow field measurements around the orbiter were estimated. The high-angle-of-attack trim characteristics of the orbiter was determined by force tests in an attempt to improve bailout conditions. A computer simulation was made to evaluate the maneuver necessary to attain the high-angle-of-attack trim.

Scallion, W. I.↗
NASA NTRS1985

Orbit on demand - Will cost determine best design?

Eleven design concepts for vertical (V) and horizontal (H) take-off launch-on-demand manned orbital vehicles are discussed. Attention is given to up to three stages, Mach numbers (sub-, 2, or 3), expendable boosters, drop tanks (DT), and storable (S) or cryogenic fuels. All the concepts feature lifting bodies with circular cross-section and most have a 7 ft diam, 15 ft long payload bay as well as a crew compartment. Expendable elements impose higher costs and in some cases reduce all-azimuth launch capabilities. Single-stage vehicles simplify the logistics whether in H or V configuration. A two-stage H vehicle offers launch offset for the desired orbital plane before firing the rocket engines after take-off and subsonic acceleration. A two-stage fully reusable V form has the second lowest weight of the vehicles studied and an all-azimuth launch capability. Better definition of the prospective mission requirements is needed before choosing among the alternatives.

Macconochie, J. O.↗
NASA NTRS1985

Space Shuttle Orbiter trimmed center-of-gravity extension study. Volume 9: Effects of configuration modifications on the aerodynamic characteristics of the 140 A/B Orbiter at Mach numbers of 1.5, 2.0, and 2.5

Wind-tunnel tests were conducted at Mach 1.5 to 2.5 to determine the effect of modifications designed to extend the forward center-of-gravity trim capability on the static longitudal and lateral directional characteristics of a Space shuttle 140 A/B orbiter model (0.01 scale). The modifications consisted of a forward-extended wing fillet, a flat plate canard, and a blended canard. The investigation was conducted in the low Mach number test section of the Langley unitary plan wind tunnel at a Reynolds number of approximately 2.15 million based on the fuselage reference length. The test angle of attack range was -1 deg to 32 deg and the sideslip angles were 0 deg and 5 deg.

Phillips, W. P.↗
NASA NTRS1984

Space Shuttle Orbiter trimmed center-of-gravity extension study. Volume 8: Effects of configuration modifications on the aerodynamic characteristics of the 140 A/B Orbiter at a Mach number of 5.97

Aerodynamic characteristics at M=5.97 for the 140 A/B Space Shuttle Orbiter configuration and for the configuration modified by geometric changes in the wing planform fillet region and the fuselage forebody are presented. The modifications, designed to extend the orbiter's longitudinal trim capability to more forward center of gravity locations, include reshaping the baseline wing fillet, changing the fuselage forebody camber, and adding canards. The Langley 20 inch Mach 6 Tunnel at a Reynolds number of approximately 6 million based on fuselage reference length was used. The angle of attack range of the investigation varied from about 15 deg to 35 deg at 0 deg and -5 deg sideslip angles. Data are obtained with the elevators and body flap deflected at appropriate negative and positive conditions to assess the trim limits.

Phillips, W. P.↗
NASA NTRS1983

Base drag determination for STS flights 1-5

Predicting the base drag characteristics for blunt based vehicles such as the Space Shuttle orbiter in gliding flight is difficult, particularly at transonic speeds. Data from the first five flights (STS 1-5) of the orbiter Columbia have been utilized to obtain the interference-free, base drag characteristics. These base drag characteristics are compared to preflight predictions derived from wind tunnel tests. Base drag is shown to account for as much as 50 percent of the total orbiter drag at transonic speeds.

Phillips, W. P.↗
NASA NTRS1983

Booster and orbiter configurations

In the recent Future Space Transportation System (FSFS) study, a mission model was selected and a baseline vehicle which best met model requirements was shaped. This baseline was then analyzed for flight performance, structural and subsystem weight, and operation. Figures related to a payload of 150,000 lb in a 20-ft-diam by 90-ft-long envelope became the baseline. The existence of both space-based orbital transfer vehicles (OTVs) and a space station was assumed, taking into account a transfer of the payload from the launch vehicle to OTVs at the space station for final delivery to geosynchronous orbit (GEO). A computer-aided engineering system called Aerospace Vehicle Interactive Design (AVID) was employed in connection with baseline vehicle development. It was found that approximately three-fifth of the payload weight would be cryogenic propellants for OTVs. Attention is given to problems regarding the packaging of cryogenic tankage, a payload shroud, and studies of staging for two different booster propulsion units.

Wilhite, A. W.↗
NASA NTRS1981

Space Shuttle Orbiter trimmed center-of-gravity extension study. Volume 7: Effects of configuration modifications on the subsonic aerodynamic characteristics of the 1140 A/B orbbiter at high Reynolds numbers

Subsonic longitudinal andd laternal directional characteristics were obtained for several modified configurations of the 140 A/B orbiter (0.010 scale). These modifications, designed to extend longitudinal trim capability forward of the 65 percent fuselage length station, consisted of modified wing planform fillet and a canard. Tests were performed in the Langley Low Turbulence Pressure Tunnel at Reynolds numbers from about 4.2 million to 14.3 million based on the fuselage reference length.

Phillips, W. P.↗
NASA NTRS1980

Comparisons of subsonic drag estimates derived from Pioneer Venus probes flight data with wind-tunnel results

Subsonic drag coefficients have been obtained from flight data for the Pioneer Venus multiprobes. The technique used to extract the information from the data consisted of utilizing in situ pressure and temperature measurements. Analysis of the major model parameter error sources indicates overall error levels of five percent or less in the flight values of the drag coefficient. Comparisons of the flight coefficients with preflight wind-tunnel test data showed generally good agreement except for the Sounder descent probe configuration. To preclude atmospheric phenomena as a possible explanation of this difference, additional wind-tunnel tests were performed on the Sounder descent probe. Special attempts were made to duplicate the probe geometry for tests in a high Reynolds number environment in order to achieve as realistic model and flight conditions as practical. Preliminary results from this testing in the NASA LaRC Low Turbulence Pressure Tunnel produced a drag coefficient of 0.68 at 0 deg angle of attack which is within the expected accuracy limits of the flight derived drag coefficient value of 0.72 + or - 0.04, thus eliminating atmospheric phenomena as the explanation for the initial difference.

Blanchard, R. C.↗
NASA NTRS1979

Space shuttle orbiter trimmed center-of-gravity extension study. Volume 5: Effects of configuration modifications on the aerodynamic characteristics of the 140A/B orbiter at Mach numbers of 2.5, 3.95 and 4.6

Supersonic aerodynamic characteristics are presented for the 140A/B space shuttle orbiter configuration (0.010 scale) and for the configuration modified to incorporate geometry changes in the wing planform fillet region. The modifications designed to extend the orbiter's longitudinal trim capability to more forward center-of-gravity locations, included reshaping of the baseline wing planform fillet and adding canards. The investigation was made in the high Mach number test section of the Langley Unitary Plan Wind Tunnel at a Reynolds number of approximately 2.2 million based on fuselage reference length. The angle-of-attack range for the investigation extended from -1 deg to 31 deg. Data were obtained with the elevators and body flap deflected at appropriate negative and positive conditions to assess the trim limits.

Phillips, W. P.↗
NASA NTRS1976

Space shuttle orbiter trimmed center-of-gravity extension study: Volume 2: Effects of configuration modifications on the aerodynamic characteristics of the 140 A/B orbiter at transonic speeds

Tests were conducted in the LaRC 8-foot transonic pressure tunnel to determine effects of fuselage nose and wing fillet modifications on the transonic aerodynamic characteristics of a space shuttle orbiter configuration. In addition to reshaping the baseline wing planform fillet, small canards were added to the configuration. The modifications considered were of interest in extending the forward center-of-gravity boundary for the configuration.

Phillips, W. P.↗
NASA NTRS1974

Influence of configuration details on the subsonic characteristics of a space shuttle orbiter design

An investigation was conducted in the Langley low-turbulence pressure tunnel of a model of a space shuttle orbiter design in order to determine the influence of minor configuration geometric details on the aerodynamic characteristics at subsonic speeds. A plane wing was tested with a small planform fillet; a twisted wing was tested with both a small and a large planform fillet. Tailored attitude-control propulsion-system wing-tip and body pods, trisegmented elevons, and canopy effects were also investigated. The tests were conducted at angles of attack from -3 deg to 24 deg for sideslip angles of 0 deg and 6 deg and at a Mach number of 0.25.

Decker, J. P.↗
NASA NTRS1974

Computer-aided space shuttle orbiter wing design study

An analytical and experimental investigation has been made to provide a space shuttle orbiter wing design that met the guideline requirements of landing performance, stability, and hypersonic trim for a specified center-of-gravity envelope. The analytical study was facilitated by the use of the Optimal Design Integration system (ODIN) and the experimental part of the investigation was conducted in the Langley low-turbulence pressure tunnel and the Langley continuous-flow hypersonic tunnel.

Phillips, W. P.↗