Engineering topics

Pfenninger, Werner

Publications and source records attributed to Pfenninger, Werner.

7 records

NASA NTRS1992

Design of a hybrid laminar flow control nacelle

Consideration is given to the potential application of hybrid-laminar-flow control to the external surface of a modern, high-bypass-ratio (HBR) turbofan engine nacelle. With the advent of advanced ultra-HBR fans (with bypass ratios of 10-15), the wetted areas of these nacelles approach 10 percent of the total wetted area of future commercial transports. A hybrid-laminar-flow-control pressure distribution is specified and the corresponding nacelle geometry is computed utilizing a predictor/corrector design method. Linear stability calculations are conducted to provide predictions of the extent of the laminar boundary layer. Performance studies on an advanced twin-engine transport configuration are presented to determine potential benefits in terms of reduced fuel consumption.

Wie, Yong-Sun↗

NASA NTRS1989

Optimization of natural laminar flow airfoils for high section lift-to-drag ratios in the lower Reynolds number range

Relatively thin natural-laminar-flow airfoils were arranged optimally for different design lift coefficients in the wing chord Reynolds number ranges of 200,000-600,00 and 0.875 x 10 to the 6th to 2 x 10 to the 6th. The 9.5 percent thick airfoil ASM-LRN-010, the 7.9 percent thick airfoil ASM-LRN-012, the 10.4 percent thick airfoil ASM-LRN-015, and the 8.2 percent thick airfoil ASM-LRN-017 were designed for high lift-to-drag ratios using Drela's design and analysis.

Pfenninger, Werner↗

NASA NTRS1988

Design philosophy of long range LFC transports with advanced supercritical LFC airfoils

The achievement of 70 percent laminar flow using modest boundary layer suction on the wings, empennage, nacelles, and struts of long-range LFC transports, combined with larger wing spans and lower span loadings, could make possible an unrefuelled range halfway around the world up to near sonic cruise speeds with large payloads. It is shown that supercritical LFC airfoils with undercut front and rear lower surfaces, an upper surface static pressure coefficient distribution with an extensive low supersonic flat rooftop, a far upstream supersonic pressure minimum, and a steep subsonic rear pressure rise with suction or a slotted cruise flap could alleviate sweep-induced crossflow and attachment-line boundary-layer instability. Wing-mounted superfans can reduce fuel consumption and engine tone noise.

Pfenninger, Werner↗

NASA NTRS1988

Design aspects of long range supersonic LFC airplanes with highly swept wings

The achievement of natural LFC in SST configurations featuring externally braced, very highly swept, high structural aspect ratio wing planforms results in outstandingly high cruise L/D ratios while maintaining low sonic-boom overpressures. A conceptual design study has been conducted with a view to range capability maximization in SSTs. A three-body configuration employing a highly swept, strut-braced planform, in which a central fuselage and two smaller outboard bodies alleviate structural wing bending and torsion, is noted to allow further increases in wingspan and aspect ratio which commensurately reduce lift-induced wave-plus-vortex drag and volume-induced wave drag.

Pfenninger, Werner↗

NASA NTRS1987

Long-range LFC transport

M = 0.83 Laminar Flow Control (LFC) transports, carrying large percentage payloads over a range of 20000 kilometers at cruise L/D's of 39 appear feasible with large space externally braced wings, external fuel pods, active controls, and 70 percent laminar flow on wing and tail surfaces, engine nacelles and struts, and a turbulent fuselage. A combination of a swept-forward inboard and a swept-back outer wing appears superior overall, especially for laminar flow and eliminating leading edge contamination probably caused by flyspecks and ice crystals. Wing divergence appears controllable by a combination of various methods. Wind-mounted superfans with extensive laminar flow on their nacelles appear practical. Their dominant tone noise is below the frequency range of the most strongly amplified TS-waves.

Pfenninger, Werner↗

NASA NTRS1987

Design of the low-speed NLF(1)-0414F and the high-speed HSNLF(1)-0213 airfoils with high-lift systems

The design and testing of Natural Laminar Flow (NLF) airfoils is examined. The NLF airfoil was designed for low speed, having a low profile drag at high chord Reynolds numbers. The success of the low speed NLF airfoil sparked interest in a high speed NLF airfoil applied to a single engine business jet with an unswept wing. Work was also conducted on the two dimensional flap design. The airfoil was decambered by removing the aft loading, however, high design Mach numbers are possible by increasing the aft loading and reducing the camber overall on the airfoil. This approach would also allow for flatter acceleration regions which are more stabilizing for cross flow disturbances. Sweep could then be used to increase the design Mach number to a higher value also. There would be some degradation of high lift by decambering the airfoil overall, and this aspect would have to be considered in a final design.

Viken, Jeffrey K.↗

NASA NTRS1986

Advanced natural laminar flow airfoil with high lift to drag ratio

An experimental verification of a high performance natural laminar flow (NLF) airfoil for low speed and high Reynolds number applications was completed in the Langley Low Turbulence Pressure Tunnel (LTPT). Theoretical development allowed for the achievement of 0.70 chord laminar flow on both surfaces by the use of accelerated flow as long as tunnel turbulence did not cause upstream movement of transition with increasing chord Reynolds number. With such a rearward pressure recovery, a concave type deceleration was implemented. Two-dimensional theoretical analysis indicated that a minimum profile drag coefficient of 0.0026 was possible with the desired laminar flow at the design condition. With the three-foot chord two-dimensional model constructed for the LTPT experiment, a minimum profile drag coefficient of 0.0027 was measured at c sub l = 0.41 and Re sub c = 10 x 10 to the 6th power. The low drag bucket was shifted over a considerably large c sub l range by the use of the 12.5 percent chord trailing edge flap. A two-dimensional lift to drag ratio (L/D) was 245. Surprisingly high c sub l max values were obtained for an airfoil of this type. A 0.20 chort split flap with 60 deg deflection was also implemented to verify the airfoil's lift capabilities. A maximum lift coefficient of 2.70 was attained at Reynolds numbers of 3 and 6 million.

Viken, Jeffrey K.↗