Engineering Papers⌕ Search

Engineering topics

Peterson, D. L.

Publications and source records attributed to Peterson, D. L..

29 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Land-cover classification of California using mosaicking and high-speed processing

A land cover classification of Landsat MSS data has been made for the entire state of California. Digital mosaicking of 32 Landsat scenes with registered digital elevation, slope, and aspect was prepared. Stratified unsupervised clustering generated the spectral classes which were identified into 16 categories, mostly forest types, using U-2 CIR photos. A verification using 81 primary sample units resulted in a forest/nonforest accuracy of 80.2% and a commercial conifer and hardwood accuracy of 75.1%. The results are now being used in many projects throughout the state.

Peterson, D. L.↗
NASA NTRS1977

Arc heater code validation tests of heat shield materials

Results are reported for tests of candidate heat-shield materials for outer-planet entry probes, which were conducted in two different arc-heater facilities at heating rates below those predicted for entry. One facility supplied a combined radiative-convective heating environment in air while the other provided a hydrogen/helium environment for convective heating only. Both 'infinite-slab' and 'finite-slab' models consisting of various carbon phenolic (CP) and fused silica (FS) materials were tested. The test results obtained are expressed in terms of ablation rates and surface as well as in-depth temperature variations with time for the air environment and in terms of normalized ablation rate as a function of temperature for the H/He environment. The measured values are compared with calculations based on a charring material thermal response and ablation code. For the CP models, good agreement between predicted and measured mass-loss rates is noted, surface temperatures in air are predicted within 18%, and in-depth temperature predictions are shown to be conservative in comparison with measured values. For the FS models, discrepancies are found between the predicted and measured mass-loss rates and surface temperatures.

Kesselring, J. P.↗
NASA NTRS1975

Fused silica reflecting heat shields for outer planet entry probes

The development of slip-cast fused silica is discussed as a heat shield designed to meet the needs of outer-planet entry probes. The distinguishing feature of silica is its ability to reflect the radiation imposed by planetary-entry environments. This reflectivity is particularly sensitive to degradation by the presence of trace amounts of contaminants introduced by the starting materials or by processing. The microstructure of a silica configuration also significantly influences the reflectivity and other thermomechanical properties. The processing techniques attendant on controlling microstructure while maintaining purity are discussed. The selection of a starting material of essential purity precludes the use of purified natural quartz and requires the use of synthetic fused silica. The silica is characterized in a limited combined heating test environment. The surface mass loss is controlled by liquid runoff from a relatively low-temperature melt layer; the reflectance is basically maintained and the material achieves a surprisingly high heat of ablation.

Congdon, W. M.↗
NASA NTRS1974

Volume-reflecting dielectric heat shield

White, volume-reflecting dielectric material absorbs essentially none of the incident radiant energy, and continues to reflect even though in severe environment its surface is melted and is being vaporized. Process of overall reflectance in dielectric material, involving internal refractions and reflections, is similar to process of reflection in paints.

Nachtsheim, P. R.↗
NASA NTRS1973

Heat shielding for Venus entry probes.

Two contrasted approaches to ablative thermal protection of Venus entry probes are presented - a typical carbonaceous charring ablator and a dielectric reflective ablator. The interesting observation in this study is that mass loss is not the controlling variable in heat-shield sizing. A heat-soak problem determines the carbon phenolic sizing. For Teflon, the material thickness required to accomplish reflection is the sizing factor. The total heat-shield weight required to handle either steep or shallow entry is computed to be 13% less for a Teflon shield (if at least 3.2 mm are required for reflection) than for a charring ablator shield. If an efficient reflective backing is used with Teflon, the thickness can be reduced 1.0 mm and the computed weight is 31% less for Teflon than for the charring ablator. Such weight reductions may significantly increase the science payload weight of the miniprobes.

Peterson, D. L.↗
NASA NTRS1972

Reflecting ablating heat shields for planetary entry.

Heat shielding for planetary entry probes of future Jovian and Venusian missions will encounter heating levels well beyond those previously experienced. These entries are typically dominated by radiative heating from the shock layer. This paper demonstrates the potential of reflecting this incident radiation diffusely from an ablating material. This technique contrasts with the absorption experienced by char-forming or graphitic ablators. Two dielectric materials, Teflon (polytetra-fluoroethylene) and boron nitride, are examined for their ablative performance, including reflection, in a combined convective- and radiative-heating environment. For Teflon, at the conditions obtained, superimposition of radiative heating upon a convective stream causes no additional increase in surface recession over the convective only results. For boron nitride, an excellent room-temperature reflector in the visible spectrum, a decrease in reflectivity from 90 to 55 percent is experienced when the surface undergoes sublimation at high temperatures. The process of reflection in each of these materials is described in terms of backscattering from crystals. The significance of a sizable reflection as a mode of energy accommodation is demonstrated for Venusian entries as a potential reduction in mass loss due to ablation.

Peterson, D. L.↗
NASA NTRS1972

A study of graphite ablation in combined convective and radiative heating.

Comparison of graphite ablation experiment results in the diffusion-controlled oxidation and sublimation regimes with results of an equilibrium chemistry, film coefficient ablation analysis. Mass transfer and energy transfer effects are considered. Tests were conducted in an arcjet facility at convective heating rates of 600 to 800 W/sq cm, radiative heating rates up to 2900 W/sq cm, with test specimen surface pressures of 0.06, 0.1, and 0.3 atm in an air stream. The experimental and analytical mass loss and surface temperature results agreed well when the carbon vapor thermodynamic properties from the JANAF tables are used in the analysis.

Wakefield, R. M.↗