Engineering topics

Peters, D. A.

Publications and source records attributed to Peters, D. A..

15 records

NASA NTRS1988

Helicopter stability and control modeling improvements and verification on two helicopters

A linearized model of helicopter flight dynamics is developed which includes the flapping, lead-lag, and dynamic inflow degrees of freedom (DOF). The model is a combination of analytical terms and numerically determined stability derivatives, and is used to investigate the importance of the rotor DOF to stability and control modeling. The results show that the rotor DOF can have a significant impact on some of the natural modes in a linear model. The flap and dynamic inflow DOF show the greatest influence. Flapping exhibits strong coupling to the body, dynamic inflow, and to lead-lag to a lesser extent. Dynamic inflow tends to damp the high-frequency flapping modes, and reduces the damping on coupled body-flap motion. Dynamic inflow also couples to the flapping motion to produce complex roots. With body-flap and lag regressing modes as exceptions, the results show essentially similar behavior for most modes of articulated and hingeless rotor helicopters.

Schrage, D. P.↗

NASA NTRS1985

A review of dynamic inflow and its effect on experimental correlations

A review is given of the relationship between experimental data and the development of modern dynamic-inflow theory. Some of the most interesting data, first presented 10 years ago at the Dynamic Specialist's Meeting, is now reviewed in light of the newer theories. These pure blade-flapping data correlate very well with analyses that include the new dynamic inflow theory, thus verifying the theory. Experimental data are also presented for damping with coupled inplane and body motions. Although inclusion of dynamic inflow is often required to correlate this coupled data, the data cannot be used to verify any particular dynamic inflow theory due to the uncertainties in modeling the inplane degree of freedom. For verification, pure flapping is required. However, the coupled data do show that inflow is often important in such computations.

Gaonkar, G. H.↗

NASA NTRS1985

Coupled rotor-body vibrations with inplane degrees of freedom

In an effort to understand the vibration mechanisms of helicopters, the following basic studies are considered. A coupled rotor-fuselage vibration analysis including inplane degrees of freedom of both rotor and airframe is performed by matching of rotor and fuselage impedances at the hub. A rigid blade model including hub motion is used to set up the rotor flaplag equations. For the airframe, 9 degrees of freedom and hub offsets are used. The equations are solved by harmonic balance. For a 4-bladed rotor, the coupled responses and hub loads are calculated for various parameters in forward flight. The results show that the addition of inplane degrees of freedom does not significantly affect the vertical vibrations for the cases considered, and that inplane vibrations have similar resonance trends as do flapping vibrations.

Ming-Sheng, H.↗

NASA NTRS1985

Design of helicopter rotor blades for optimum dynamic characteristics

The mass and stiffness distributions for helicopter rotor blades are tailored in such a way to give a predetermined placement of blade natural frequencies. The optimal design is pursued with respect of minimum weight, sufficient inertia, and reasonable dynamic characteristics. Finite element techniques are used as a tool. Rotor types include hingeless, articulated, and teetering.

Peters, D. A.↗

NASA NTRS1984

Design of helicopter rotor blades for optimum dynamic characteristics

The optimal design of helicopter rotor blades is addressed. The forced response of an initial (i.e., non-optimized) blade to those of a final (optimized) blade are compared. Response of starting design and optimal designs for varying forcing frequencies, blade response to harmonics of rotor speed, and derivation of mass and stiffness matrices or functions of natural frequencies are discussed.

Peters, D. A.↗

NASA NTRS1984

Design of helicopter rotor blades for desired placement of natural frequencies

The mass and stiffness distributions for helicopter rotor blades are to be tailored in such a way to give a predetermined placement of blade natural frequencies. This optimization problem is addressed in a methodical, step-by-step process in which each aspect of the optimization is studied in detail. Careful consideration is also given to the mathematical formulation of the problem and to the introduction of appropriate constraints.

Peters, D. A.↗

NASA NTRS1983

Design of helicopter rotor blades for optimum dynamic characteristics

The possibilities and limitations of tailoring blade mass and stiffness distributions to give an optimum blade design in terms of weight, inertia, and dynamic characteristics are discussed. The extent that changes in mass of stiffness distribution can be used to place rotor frequencies at desired locations is determined. Theoretical limits to the amount of frequency shift are established. Realistic constraints on blade properties based on weight, mass, moment of inertia, size, strength, and stability are formulated. The extent that the hub loads can be minimized by proper choice of E1 distribution, and the minimum hub loads which can be approximated by a design for a given set of natural frequencies are determined. Aerodynamic couplings that might affect the optimum blade design, and the relative effectiveness of mass and stiffness distribution on the optimization procedure are investigated.

Peters, D. A.↗

NASA NTRS1982

Design of helicopter rotor blades for optimum dynamic characteristics

The possibilities and the limitations of tailoring blade mass and stiffness distributions to give an optimum blade design in terms of weight, inertia, and dynamic characteristics are investigated. Changes in mass or stiffness distribution used to place rotor frequencies at desired locations are determined. Theoretical limits to the amount of frequency shift are established. Realistic constraints on blade properties based on weight, mass moment of inertia size, strength, and stability are formulated. The extent hub loads can be minimized by proper choice of EL distribution is determined. Configurations that are simple enough to yield clear, fundamental insights into the structural mechanisms but which are sufficiently complex to result in a realistic result for an optimum rotor blade are emphasized.

Peters, D. A.↗

NASA NTRS1980

On the nonlinear deformation geometry of Euler-Bernoulli beams

Nonlinear expressions are developed to relate the orientation of the deformed beam cross section, torsion, local components of bending curvature, angular velocity, and virtual rotation to deformation variables. The deformed beam kinematic quantities are proven to be equivalent to those derived from various rotation sequences by identifying appropriate changes of variable based on fundamental uniqueness properties of the deformed beam geometry. The torsion variable used is shown to be mathematically analogous to an axial deflection variable commonly used in the literature. Rigorous applicability of Hamilton's principle to systems described by a class of quasi-coordinates that includes these variables is formally established.

Hodges, D. H.↗

NASA NTRS1976

Hingeless helicopter rotor with improved stability

Improved stability was provided in a hingeless helicopter rotor by inclining the principal elastic flexural axes and coupling pitching of the rotor blade with the lead-lag bending of the blade. The primary elastic flex axes were inclined by constructing the blade of materials that display non-uniform stiffness, and the specification described various cross section distributions and the resulting inclined flex axes. Arrangements for varying the pitch of the rotor blade in a predetermined relationship with lead-lag bending of the blade, i.e., bending of the blade in a plane parallel to its plane of rotation were constructed.

Ormiston, R. A.↗

NASA NTRS1975

New design of hingeless helicopter rotor improves stability

Cantilever blades are attached directly to rotor hub, thereby substantially reducing cost and complexity and increasing reliability of helicopter rotor. Combination of structural flap-lag coupling and pitch-lag coupling provides damping of 6 to 10%, depending on magnitude of coupling parameters.

Ormiston, R. A.↗

NASA NTRS1975

An approximate closed-form solution for lead lag damping of rotor blades in hover

Simple stability methods are used to derive an approximate, closed-form expression for the lead-lag damping of rotor blades in hover. Destabilizing terms are shown to be a result of two dynamic mechanisms. First, the destabilizing aerodynamic forces that can occur when blade lift is higher than a critical value are maximized when the blade motion is in a straight line equidistant from the blade chord and the average direction of the air flow velocity. This condition occurs when the Coriolis terms vanish and when the elastic coupling terms align the blade motion with this least stable direction. Second, the nonconservative stiffness terms that result from pitch-flap or pitch-lag coupling can add or subtract energy from the system depending upon whether the motion of the blade tip is clockwise or counterclockwise.

Peters, D. A.↗

NASA NTRS1975

Flapping response characteristics of hingeless rotor blades by a gereralized harmonic balance method

Linearized equations of motion for the flapping response of flexible rotor blades in forward flight are derived in terms of generalized coordinates. The equations are solved using a matrix form of the method of linear harmonic balance, yielding response derivatives for each harmonic of the blade deformations and of the hub forces and moments. Numerical results and approximate closed-form expressions for rotor derivatives are used to illustrate the relationships between rotor parameters, modeling assumptions, and rotor response characteristics. Finally, basic hingeless rotor response derivatives are presented in tabular and graphical form for a wide range of configuration parameters and operating conditions.

Peters, D. A.↗

NASA NTRS1974

Hingeless rotor frequency response with unsteady inflow

Hingeless rotor frequency response calculations are obtained by applying a generalized harmonic balance to the elastic blade flapping equations. Nonuniform, unsteady induced flow effects are included by assuming a simple three-degree-of-freedom description of the rotor wake. Results obtained by using various models of elastic blade bending and induced flow are compared with experimental data obtained from a 7.5-ft diameter wind tunnel model at advance ratios from 0.0 to 0.6. It is shown that the blade elasticity and nonuniform, unsteady induced flow can have a significant effect on the transient response characteristics of rotor systems.

Peters, D. A.↗

NASA NTRS1973

An approximate solution for the free vibrations of rotating uniform cantilever beams

Approximate solutions are obtained for the uncoupled frequencies and modes of rotating uniform cantilever beams. The frequency approximations for flab bending, lead-lag bending, and torsion are simple expressions having errors of less than a few percent over the entire frequency range. These expressions provide a simple way of determining the relations between mass and stiffness parameters and the resultant frequencies and mode shapes of rotating uniform beams.

Peters, D. A.↗