Engineering Papers⌕ Search

Engineering topics

Peter, William

Publications and source records attributed to Peter, William.

Additive Manufacturing of Lightweight Structures: Microfibrillated Cellulose – PLA Biofoams

Extrusion-based polymer additive manufacturing (AM) technology is growing rapidly. The introduction of fiber reinforced feedstock materials and recent developments in the manufacturing systems have promulgated large scale AM of composites to create new industries and applications. Synthetic fibers such as carbon and glass fibers are commonly used to reinforce polymer composites. However, increasing environmental and long-term sustainability concerns are leading to new materials using cellulose fiber reinforcement in bio-derived polymers. These materials offer new property sets, new supply chains and have the potential to provide economical solutions leading to new applications. Large scale AM can be attractive for many different applications because of its ability to freeform manufacture complex geometries; each application may require different material properties. One of the novel application areas for large scale AM is 3D printing of lightweight materials via foaming. Although achieving low density is the key in light weighting via foaming, mechanical performance is also important for many applications. In this study the impact of micro-cellulose fibers (MFC) on foaming behavior and the mechanical properties of additively manufactured parts is investigated. MFC-polylactic acid (PLA) feedstock pellets were prepared at varying MFC content (5, 10, 15 and 20 wt.%) to understand the impact of cellulose fiber content on density and mechanical properties of the AM biocomposites. Also, the impact of extrusion speed and foaming agent content on the AM biocomposites is investigated. Although achieving uniform printed foam structure is challenging with the presence of cellulose fibers, promising results were accomplished with density values below 0.5g/cm3.

Tekinalp, Halil↗

Additive manufacturing of power poles using bamboo-polymer composites: A quick solution for power grid restoration

Polymer additive manufacturing (AM) technology is rapidly growing and its transition to become an advanced manufacturing technique now offers possibilities for unconventional applications. One of these potential applications is on site additive manufacturing of power poles. During natural incidents such as storms and hurricanes, power lines can be severely damaged and there may not be sufficient spare power poles to replace. In such situations, additive manufacturing of power poles on site can offer a fast, temporary solution during emergencies. The ability of freeform manufacturing of parts with complex geometries makes large scale AM attractive for various applications; however, due to residual stress build up and need for different mechanical requirements for different applications, reinforcement of the AM feedstock is necessary. In addition to carbon and glass fibers, bio-derived fibers can also be used as a reinforcing phase, both to utilize the natural resources at the emergency area and in terms of long-term sustainability. In this project, design and additive manufacturing of a 13.1 m power pole was demonstrated. Three different feedstock material options (polystyrene, cellulose ester and polycarbonate reinforced with glass and bamboo fibers) and two different pole designs were investigated. As-printed part tensile properties both in printing and interlayer directions were measured and a power pole was printed as six pieces and put together successfully. Finally, a conceptual design of a portable power pole manufacturing approach was proposed.

Tekinalp, Halil↗

First Digit Oscillations

The frequency of the first digits of numbers drawn from an exponential probability density oscillate around the Benford frequencies. Analysis, simulations and empirical evidence show that datasets must have at least 10,000 entries for these oscillations to emerge from finite-sample noise. Anecdotal evidence from population data is provided.

97 MATHEMATICS AND COMPUTING↗

Additively Manufactured Single-Use Molds and Reusable Patterns for Large Automotive and Hydroelectric Components

Additive manufacturing (AM) has the potential to reduce costs in the casting industry, particularly for large parts (i.e., components with any dimension > 12 in.). In this study, pilot-scale production case studies of hydroelectric and automotive parts were used to evaluate two AM-enabled casting methods: the direct printing of sand molds by binder jet and printing of reusable cope and drag patterns for sand casting. An additional benefit was found when additively manufactured patterns were used in combination with heat-treat free aluminum alloys, to produce castings of complex hydrodynamic surfaces. These parts previously required production via subtractive machining due to part distortion induced by the quench step of heat treatments. The machine types used for the three case studies are sand-binder jet, high-resolution polymer fused deposition modeling (FDM), and big area additive manufacturing (BAAM) FDM in combination with CNC machining. Each method demonstrated distinct advantages over traditional casting practices in particular use cases. Single-use molds show great reductions in start-up cost to produce one-off or legacy parts, and additively manufactured impression patterns show promise for innovating the tooling design process for complex geometry and large castings.

36 MATERIALS SCIENCE↗

High modulus biocomposites via additive manufacturing: Cellulose nanofibril networks as “microsponges”

For the successful transition of additive manufacturing (AM) from prototyping to manufacturing of structural load bearing parts, feedstock systems with improved mechanical properties are needed. In terms of sustainability and environmental impact, selection of biobased renewable alternatives instead of petroleum-based options is important. Nanocellulose, which gives plants and trees their structural integrity, can offer significant improvements in the mechanical properties of AM polymers, provided that the right fibril morphology, dispersion and adhesion are achieved. In this study, although the interfacial adhesion between the hydrophilic cellulose nanofibrils (CNFs) and the hydrophobic polylactate matrix was not strong, and the optimal dispersion in individual fibril level was not attained, dramatic improvements in mechanical properties of neat polymer were achieved (up to 80% tensile strength increase, up to 200% elastic modulus increase). An interlocking reinforcing mechanism in which CNF bundles act as “microsponges” was proposed and supported by high resolution electron microscopy images, x-ray computed chromatography scans and thermal and dynamic mechanical behavior. Additively manufactured samples showed significantly higher elastic modulus (7.12 GPa vs. 6.57 GPa at 30 wt % CNF content) and dramatically improved storage modulus (1.72 GPa vs. 0.9 GPa at 30 wt % CNF content) in the printing direction compared to compression molded samples. Finally, in conclusion, preparation and 3D-printing of a 100% biobased renewable feedstock material with substantial mechanical property improvements were successfully demonstrated, which can open up new window of opportunities in the AM industry.

42 ENGINEERING↗

Effect of surface treatment of microfiberlated cellulose fibers on biocomposite properties and additive manufacturing process

Polymer additive manufacturing (AM) is a rapidly growing technology and it is transitioning to become an advanced manufacturing technique with the introduction of fiberlar reinforcing materials such as carbon and glass fibers into polymer feedstock. As a result of increasing environmental and long-term sustainability concerns, there is an increasing interest in using bio-derived cellulose fibers to reinforce composites instead of carbon and glass fibers. Melt extrusion/fused filament fabrication method is the most commonly used polymer AM technique which enables direct digital manufacturing of parts with complex geometry with a controlled anisotropic distribution of reinforcing phase. However, there are multiple factors that affect the mechanical performance of the final part such as the dispersion and orientation of the reinforcing fibers, the adhesion between the fibers and the polymer matrix, and the porosity/defects present in the part. Chemical modification of the surface of the reinforcing fibers is an effective way of improving the fiber-polymer interaction. Furthermore, the improved adhesion between the fibers and the polymer can also enhance the fiber dispersion, improve the rheological behavior of the molten feedstock and minimize the formation of porosity during the printing process, which is one of the major issues in AM. In this study, we are investigating the effect of silane surface treatment of micro-cellulose fibers on the thermal, rheological and mechanical properties of cellulose-PLA biocomposites and on the 3D-printing process. X-ray photoelectron spectroscopy results confirmed the increase in amine and silane groups on the surface of modified fibers, indicating successful functionalization. Thermal and mechanical characterization of modified fiber-PLA composites showed significant increases in storage modulus, glass transition temperature, and complex viscosity compared to neat PLA.

Tekinalp, Halil↗

Considerations for Application of Additive Manufacturing to Nuclear Reactor Core Components

The following chapter represents the current state of literature on the selected additive manufacturing technologies and was written with an emphasis on quality control and material performance repeatability. Research and standards published by government entities such as the National Institute of Standards and Technology (NIST) and Department of Energy (DOE) have been included where applicable. It is recommended that literature be reviewed, and new knowledge integrated no less frequently than every four years due to the rapid pace of advancements in additive manufacturing and associated industries. AM presents unique challenges in certification for NPP applications such as anisotropic material properties, porosity, underdeveloped process control feedback systems, and reproducibility. This chapter begins with an overview of the selected AM technologies, followed by a systematic review of literature to detail the fabrication process and difficulties with repeatably fabricating fully dense, geometrically accurate components with known material properties.

36 MATERIALS SCIENCE↗

MICRO-CELLULOSE FIBER REINFORCED BIOCOMPOSITES FOR ADDITIVE MANUFACTURING

Polymer additive manufacturing (AM) technology is rapidly growing and it is transitioning from being primarily a prototyping method to an advanced manufacturing technique. Melt extrusion/fused deposition modeling, a method in which molten thermoplastic-based feedstock material is deposited in a raster pattern layer by layer, is the most commonly used technique in polymer AM. The technique enables direct digital manufacturing of desired geometry with controlled anisotropic distribution of reinforcing phase. While thermoplastic composites are being used in many areas of industry including AM, due to increasing environmental and long-term sustainability concerns, there is an increasing interest in bio-based renewable alternatives. Nano-to-mm scale plant-based fibers are utilized to improve properties of thermoplastics and produce bio-composites. The effect of commercially available micro-scale cellulose fibers (MFC) on the mechanical and rheological behavior of polylactic acid to produce fully bio-based composites are being investigated and selected formulations will be 3D-printed to investigate the effect of printing process on MFC alignment. Significant increases in both tensile strength and elastic modulus of compression-molded MFC-PLA composites were observed at 40 % (by wt) fiber levels.

Tekinalp, Halil↗

Free Form Fluidics

This work introduces the concept of blending fluid power with mechanical structure through addictive manufacturing. Today, fluid-powered devices are manufactured using conventional fabrication practices. The additive process enables integrated structure, actuation, fluid passages, thermal management, and control within a single fabrication process. Fluid can be routed efficiently through the structure without the need for cross-drilled holes or plugs. Fluid passages can be optimized for heat dissipation and minimized head loss. One of the primary issues regarding parts manufactured using the additive manufacturing process is their mechanical properties. Results show that components made with Ti-6-4 powders have a minimum yield stress and ultimate strength that exceeds Grade 5 specifications. The Arcan system uses a powder bed that has an elevated temperature. Therefore, the part exhibits very little residual stress during the manufacturing process. This leads to improved mechanical strength but induces challenges in powder removal. The specific advantages are reduced weight, potential for lower cost, and reduced part counts.

42 ENGINEERING↗

Neutron Characterization for Additive Manufacturing

Oak Ridge National Laboratory (ORNL) is leveraging decades of experience in neutron characterization of advanced materials together with resources such as the Spallation Neutron Source (SNS) and the High Flux Isotope Reactor (HFIR) shown in Fig. 1 to solve challenging problems in additive manufacturing (AM). Additive manufacturing, or three-dimensional (3-D) printing, is a rapidly maturing technology wherein components are built by selectively adding feedstock material at locations specified by a computer model. The majority of these technologies use thermally driven phase change mechanisms to convert the feedstock into functioning material. As the molten material cools and solidifies, the component is subjected to significant thermal gradients, generating significant internal stresses throughout the part (Fig. 2). As layers are added, inherent residual stresses cause warping and distortions that lead to geometrical differences between the final part and the original computer generated design. This effect also limits geometries that can be fabricated using AM, such as thin-walled, high-aspect- ratio, and overhanging structures. Distortion may be minimized by intelligent toolpath planning or strategic placement of support structures, but these approaches are not well understood and often "Edisonian" in nature. Residual stresses can also impact component performance during operation. For example, in a thermally cycled environment such as a high-pressure turbine engine, residual stresses can cause components to distort unpredictably. Different thermal treatments on as-fabricated AM components have been used to minimize residual stress, but components still retain a nonhomogeneous stress state and/or demonstrate a relaxation-derived geometric distortion. Industry, federal laboratory, and university collaboration is needed to address these challenges and enable the U.S. to compete in the global market. Work is currently being conducted on AM technologies at the ORNL Manufacturing Demonstration Facility (MDF) sponsored by the DOE's Advanced Manufacturing Office. The MDF is focusing on R&D of both metal and polymer AM pertaining to in-situ process monitoring and closed-loop controls; implementation of advanced materials in AM technologies; and demonstration, characterization, and optimization of next-generation technologies. ORNL is working directly with industry partners to leverage world-leading facilities in fields such as high performance computing, advanced materials characterization, and neutron sciences to solve fundamental challenges in advanced manufacturing. Specifically, MDF is leveraging two of the world's most advanced neutron facilities, the HFIR and SNS, to characterize additive manufactured components.

Watkins, Thomas↗

Reactive power interconnection requirements for PV and wind plants : recommendations to NERC

Voltage on the North American bulk system is normally regulated by synchronous generators, which typically are provided with voltage schedules by transmission system operators. In the past, variable generation plants were considered very small relative to conventional generating units, and were characteristically either induction generator (wind) or line-commutated inverters (photovoltaic) that have no inherent voltage regulation capability. However, the growing level of penetration of non-traditional renewable generation - especially wind and solar - has led to the need for renewable generation to contribute more significantly to power system voltage control and reactive power capacity. Modern wind-turbine generators, and increasingly PV inverters as well, have considerable dynamic reactive power capability, which can be further enhanced with other reactive support equipment at the plant level to meet interconnection requirements. This report contains a set of recommendations to the North-America Electricity Reliability Corporation (NERC) as part of Task 1-3 (interconnection requirements) of the Integration of Variable Generation Task Force (IVGTF) work plan. The report discusses reactive capability of different generator technologies, reviews existing reactive power standards, and provides specific recommendations to improve existing interconnection standards.

14 SOLAR ENERGY↗