Engineering Papers⌕ Search

Engineering topics

Perez, Danielle M.

Publications and source records attributed to Perez, Danielle M..

Improvements to Modeling Capabilities of ATF Concepts in the BISON Fuel Performance Code

Research into accident tolerant materials for the fuel and cladding in Light Water Reactors has been at the forefront of the nuclear fuel research community since the events that occurred at the Fukushima Daiichi nuclear power plant in March 2011. Accident tolerant materials are defined as those that provide significantly increased response time in the event of an accident while providing similar or improved performance as the conventional UO{sub 2}/zirconium-based cladding fuel rods during normal operation. In particular, qualitative attributes for materials with enhanced accident tolerance include improved reaction (e.g., oxidation) kinetics with steam, resulting in lower hydrogen (or other combustible gases) generation rate, while maintaining acceptable thermo-mechanical properties, fuel-clad interactions, and fission-product behavior. Through it's Office of Nuclear Energy, the United States Department of Energy (U.S. DOE) has accelerated research in this area through the Fuel Cycle Research and Development (FCRD) Advanced Fuels Campaign (AFC). The goal of the AFC Accident Tolerant Fuel (ATF) program is to guide selection of promising concepts for insertion into a commercial reactor as part of a lead test rod or assembly in 2022. Given the aggressive development schedule, it is impossible to perform a comprehensive set of experiments to provide material characterization data. Therefore, the AFC is utilizing computational analysis tools in an effort to understand the proposed accident tolerant materials. The two materials of interest in this work are iron-chromium-aluminum (FeCrAl) cladding and U{sub 3}Si{sub 2}. From a fuel performance standpoint, the correlations available to describe the behavior of these two materials is limited. Therefore, as additional experimental data becomes available and correlations are updated, the fuel performance models must be updated as well to assure that the material models reflect the latest experimental findings. In this paper we demonstrate the importance of utilizing the latest state-of-the-art models for fuel performance simulations by comparing the change in the updated thermal conductivity model for U{sub 3}Si{sub 2} fuel and oxidation model for FeCrAl cladding alloys using the BISON fuel performance code under normal operating conditions. The results indicate that the latest thermal conductivity model for U{sub 3}Si{sub 2} results in fuel centerline temperatures that are on average approximately 3% higher than the previous model. For the oxidation behavior of FeCrAl alloys the new model predicts observable but small oxide thickness (6 μm) compared to the previous model which predicted essentially zero oxide scale formation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improvements to Modeling Capabilities of ATF Concepts in the BISON Fuel Performance Code

Research into accident tolerant materials for the fuel and cladding in Light Water Reactors has been at the forefront of the nuclear fuel research community since the events that oc- curred at the Fukushima Daiichi nuclear power plant in March 2011. Accident tolerant materials are defined as those that provide significantly increased response time in the event of an accident while providing similar or improved performance as the conventional UO2/zirconium-based cladding fuel rods dur- ing normal operation [1]. In particular, qualitative attributes for materials with enhanced accident tolerance include im- proved reaction (e.g., oxidation) kinetics with steam, resulting in slower hydrogen (or other combustible gases) generation rate, while maintaining acceptable thermo-mechanical prop- erties, fuel-clad interactions, and fission-product behavior [1]. Through its Office of Nuclear Energy the United States De- partment of Energy (U.S. DOE) has accelerated research in this area through the Fuel Cycle Research and Development (FCRD) Advanced Fuels Campaign (AFC). The goal of the AFC Accident Tolerant Fuel (ATF) program is to guide se- lection of promising concepts for insertion into a commercial reactor as part of a lead test rod or assembly in 2022. Given the aggressive development schedule, it is impossi- ble to perform a comprehensive set of experiments to provide material characterization data. Therefore, the AFC is utilizing computational analysis tools in an effort to understand the proposed accident tolerant materials. The two materials of interest in this work are iron-chromium-aluminum (FeCrAl) cladding and U3Si2. From a fuel performance standpoint, the correlations available to describe the behavior of these two materials is limited. Therefore, as additional experimental data becomes available and correlations are updated, the fuel performance models must be updated to represent the current state of the art understanding of these materials. In this paper we demonstrate the importance of utilizing the latest state-of-the-art models for fuel performance simula- tions by comparing old and new thermal conductivity models for U3Si2 fuel and old and new oxidation models for FeCrAl cladding alloys using the BISON [2, 3] fuel performance code under normal operating conditions. The results indicate that the latest thermal conductivity model for U3Si2 results in fuel centerline temperatures that are on average approximately 3% higher than the previous model. For the oxidation behavior of FeCrAl alloys the new model predicts observable but small ox- ide thickness (~6 µm) compared to the previous model which predicted zero oxide scale formation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Physics-based multiscale coupling for full core nuclear reactor simulation

Numerical simulation of nuclear reactors is a key technology in the quest for improvements in efficiency, safety, and reliability of both existing and future reactor designs. Historically, simulation of an entire reactor was accomplished by linking together multiple existing codes that each simulated a subset of the relevant multiphysics phenomena. Recent advances in the MOOSE (Multiphysics Object Oriented Simulation Environment) framework have enabled a new approach: multiple domain-specific applications, all built on the same software framework, are efficiently linked to create a cohesive application. This is accomplished with a flexible coupling capability that allows for a variety of different data exchanges to occur simultaneously on high performance parallel computational hardware. Examples based on the KAIST-3A benchmark core, as well as a simplified Westinghouse AP-1000 configuration, demonstrate the power of this new framework for tackling—in a coupled, multiscale manner—crucial reactor phenomena such as CRUD-induced power shift and fuel shuffle. 2014 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY-NC-SA license

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Uncertainty and sensitivity analysis of fission gas behavior in engineering-scale fuel modeling

The role of uncertainties in fission gas behavior calculations as part of engineering-scale nuclear fuel modeling is investigated using the BISON fuel performance code and a recently implemented physics-based model for the coupled fission gas release and swelling. Through the integration of BISON with the DAKOTA software, a sensitivity analysis of the results to selected model parameters is carried out based on UO2 single-pellet simulations covering different power regimes. The parameters are varied within ranges representative of the relative uncertainties and consistent with the information from the open literature. The study leads to an initial quantitative assessment of the uncertainty in fission gas behavior modeling with the parameter characterization presently available. Also, the relative importance of the single parameters is evaluated. Moreover, a sensitivity analysis is carried out based on simulations of a fuel rod irradiation experiment, pointing out a significant impact of the considered uncertainties on the calculated fission gas release and cladding diametral strain. The results of the study indicate that the commonly accepted deviation between calculated and measured fission gas release by a factor of 2 approximately corresponds to the inherent modeling uncertainty at high fission gas release. Nevertheless, higher deviations may be expected for values around 10% and lower. Implications are discussed in terms of directions of research for the improved modeling of fission gas behavior for engineering purposes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

RERTR-12 Insertion 2 Irradiation Summary Report

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-12 was designed to provide comprehensive information on the performance of uranium-molybdenum (U-Mo) based monolithic fuels for research reactor applications.1 RERTR-12 insertion 2 includes the capsules irradiated during the last three irradiation cycles. These capsules include Z, Y1, Y2 and Y3 type capsules. The following report summarizes the life of the RERTR-12 insertion 2 experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

RERTR-13 Irradiation Summary Report

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-13 was designed to assess performance of different types of neutron absorbers that can be potentially used as burnable poisons in the low enriched uranium-molybdenum based dispersion and monolithic fuels.1 The following report summarizes the life of the RERTR-13 experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AFIP-7 Irradiation Summary Report

The A dvanced Test Reactor (ATR) F ull size plate I n center flux trap P osition (AFIP) experiment AFIP-7 was designed to evaluate the performance of monolithic uranium-molybdenum (U-Mo) fuels in geometries which are prototypic of US high power research reactor (HPRR) fuel plates. The following report summarizes the life of the AFIP-7 experiment through end of irradiation, including a brief description of the safety analysis, as-run neutronic analysis results, hydraulic testing results, and thermal analysis results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AFIP-6 Mark II Irradiation Summary Report

Due to the incompletion of the A dvanced Test Reactor (ATR) F ull size plate I n center flux trap P osition (AFIP) experiment AFIP-6, a second irradiation (named AFIP-6 Mark II) of identical plates was performed. AFIP-6 Mark II was designed to evaluate high-power large-scale performance of monolithic uranium-molybdenum (U-Mo) fuels. The following report summarizes the life of the AFIP-6 MKII experiment through end of irradiation, including a brief description of the safety analysis, as-run neutronic analysis results, hydraulic testing results, and thermal analysis results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

RERTR-12 Insertion 1 Irradiation Summary Report

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-12 was designed to provide comprehensive information on the performance of uranium-molybdenum (U-Mo) based monolithic fuels for research reactor applications. RERTR-12 insertion 1 includes the capsules irradiated during the first two irradiation cycles. These capsules include Z, X1, X2 and X3 capsules. The following report summarizes the life of the RERTR-12 insertion 1 experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AFIP-4 Irradiation Summary Report

The Advanced Test Reactor (ATR) Full size plate In center flux trap Position (AFIP) experiment AFIP-4 was designed to evaluate the performance of monolithic uranium-molybdenum (U-Mo) fuels at a scale prototypic of research reactor fuel plates. The AFIP-4 test further examine the fuel/clad interface and its behavior under extreme conditions. After irradiation, fission gas retention measurements will be performed during post irradiation (PIE)1,2. The following report summarizes the life of the AFIP-4 experiment through end of irradiation, including a brief description of the safety analysis, as-run neutronic analysis results, hydraulic testing results, and thermal analysis results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

RERTR-6 Irradiation Summary Report

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-6 was designed to evaluate several modified fuel designs that were proposed to address the possibility of breakaway swelling due to porosity within the (U. Mo) Al interaction product observed in the full-size plate tests performed in Russia and France. The following report summarizes the life of the RERTR-6 experiment through end of irradiation, including as-run neutronic analyses, thermal analyses and hydraulic testing results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

RERTR-7 Irradiation Summary Report

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-7A, was designed to test several modified fuel designs to target fission densities representative of a peak low enriched uranium (LEU) burnup in excess of 90% U-235 at peak experiment power sufficient to generate a peak surface heat flux of approximately 300 W/cm 2 . The RERTR-7B experiment was designed as a high power test of 'second generation' dispersion fuels at peak experiment power sufficient to generate a surface heat flux on the order of 230 W/cm 2 . The following report summarizes the life of the RERTR-7A and RERTR-7B experiments through end of irradiation, including as-run neutronic analyses, thermal analyses and hydraulic testing results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

RERTR-8 Irradiation Summary Report

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-8, was designed to test monolithic mini-fuel plates fabricated via hot isostatic pressing (HIP), the effect of molybdenum (Mo) content on the monolithic fuel behavior, and the efficiency of ternary additions to dispersion fuel particles on the interaction layer behavior at higher burnup. The following report summarizes the life of the RERTR-8 experiment through end of irradiation, including as-run neutronic analysis, thermal analysis and hydraulic testing results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AFIP-6 Irradiation Summary Report

The Advanced Test Reactor (ATR) Full size plate In center flux trap Position (AFIP) experiment AFIP-6 was designed to evaluate the performance of monolithic uranium-molybdenum (U-Mo) fuels at a length prototypic to that of the ATR fuel plates (45 inches in length). The AFIP-6 test was the first test with plates in a swaged condition with longer fuel zones of approximately 22.5 inches in length. The following report summarizes the life of the AFIP-6 experiment through end of irradiation, including a brief description of the safety analysis, as-run neutronic analysis results, hydraulic testing results, and thermal analysis results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗