Engineering Papers⌕ Search

Engineering topics

Pegg, R. J.

Publications and source records attributed to Pegg, R. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Pulse Detonation Engine Air Induction System Analysis

A preliminary mixed-compression inlet design concept for potential pulse-detonation engine (PDE) powered supersonic aircraft was defined and analyzed. The objectives of this research were to conceptually design and integrate an inlet/PDE propulsion system into a supersonic aircraft, perform time-dependent CFD analysis of the inlet flowfield, and to estimate the installed PDE cycle performance. The study was baselined to a NASA Mach 5 Waverider study vehicle in which the baseline over/under turboramjet engines were replaced with a single flowpath PDE propulsion system. As much commonality as possible was maintained with the baseline configuration, including the engine location and forebody lines. Modifications were made to the inlet system's external ramp angles and a rotating cowl lip was incorporated to improve off-design inlet operability and performance. Engines were sized to match the baseline vehicle study's ascent trajectory thrust requirement at Mach 1.2. The majority of this study was focused on a flight Mach number of 3.0. The time-dependent Navier Stokes CFD analyses of a two-dimensional approximation of the inlet was conducted for the Mach 3.0 condition. The Lockheed Martin Tactical Aircraft Systems-developed FALCON CFD code with a two equation 'k-1' turbulence model was used. The downstream PDE was simulated by an array of four sonic nozzles in which the flow areas were rapidly varied in various opening/closing combinations. Results of the CFD study indicated that the inlet design concept operated successfully at the Mach 3.0 condition, satisfying mass capture, total pressure recovery, and operability requirements. Time-dependent analysis indicated that pressure and expansion waves from the simulated valve perturbations did not effect the inlet's operability or performance.

Pegg, R. J.↗
NASA NTRS1984

Design of long-endurance unmanned airplanes incorporating solar and fuel cell propulsion

Attention is given to the design features and operational capabilities of a class of unmanned flight vehicles possessing multiday mission endurance capabilities, based on the use of a mixed-mode electric power system which incorporates solar cells for diurnal energy production and a nonregenerative H2-O2 fuel cell for nocturnal energy supply. Energy is thereby provided for not only propulsion, but also the operation of the payload and the vehicle's avionics. The excess solar energy available during high insolation portions of the diurnal period may be used for climb/maneuvering or payload-related functions. Empirical structure scaling algorithms are combined with low Reynolds number aerodynamics algorithms to estimate requisite size and geometry for the chosen mission. Wing loadings will be of the order of 0.9-1.3 lb/sq ft.

Youngblood, J. W.↗
NASA NTRS1980

Aeroacoustic wind-tunnel tests of a light twin-boom general-aviation airplane with free or shrouded-pusher propellers

Tests were conducted in the Langley full-scale tunnel to determine the aerodynamic performance and acoustic characteristics of four different pusher-propeller configurations on a twin boom, general aviation airplane. The propellers included a 2-blade free propeller, two 3-blade shrouded propellers, and a 5-blade shrouded propeller. The tests were conducted for a range of airplane angles of attack from about 0 deg to 16 deg for test speeds from 0 to about 36 m/sec and for a range of propeller blade angles and rotation speeds. The free propeller provided the best aerodynamic propulsive performance. For forward flight conditions, the free propeller noise levels were lower than those of the shrouded propellers. In the static conditions the free propeller noise levels were as low as those for the shrouded propellers, except for the propeller in-plane noise where the shrouded propeller noise levels were lower.

Mclemore, H. C.↗
NASA NTRS1978

Exploratory wind-tunnel investigation of the effect of the main rotor wake on tail rotor noise

Approaches to minimizing the noise generated by the interaction of the tail rotor blades with the wake of the main rotor considered include repositioning of the tail rotor with respect to the main rotor, changes in the rotational direction of the tail rotor, and modification of the main rotor tip vortex. A variable geometry model was built which had the capability of varying tail rotor position relative to the main rotor as well as direction of tail rotor rotation. Acoustic data taken from the model in the Langley anechoic noise facility indicates interaction effects due to both main rotor shed vortex and the main rotor turbulence.

Pegg, R. J.↗
NASA NTRS1977

Some measured and calculated effects of a tip vortex modification device on impulsive noise

The results of a recent wind tunnel test program to evaluate the effectiveness of the Tip Air Mass Injection (TAMI) system in modifying the blade tip vortex occurring during helicopter flight is described with attention to the effect of this modification on the impulsive noise. The measurement program is explained, and the correlation between experimental and predicted results is discussed. Topics considered include the effect of descent rate on noise pressure time histories, the effect of air mass injection on noise, and the analysis based on a dB(A) weighted approach. Impulsive noise generated by the interaction of a helicopter rotor blade and the concentrated tip vortex during forward flight descent is a primary contributor to acoustic annoyance as it draws early attention to the presence of the helicopter.

Pegg, R. J.↗
NASA NTRS1977

Some measured and calculated effects of forward velocity on propeller noise

Test flights using a twin-engine, high-wing, light STOL transport plane powered by free turbine engines driving three-bladed propellers, were conducted at the NASA Wallops Flight Center. A ground-based acoustic measuring range was set up, and aircraft tracking information was supplied by a radar system. The noise of the unshrouded propeller was measured under static and forward flight conditions, and the measurements were compared with theory. Under static conditions, the principal noise is related to the unsteady loading associated with the interaction of the propeller with persistent turbulent eddies passing through the propeller disk. Through the use of existing prediction techniques, it was shown that changes in the geometry such as different airfoil thickness distribution can affect the radiated acoustic pressure signatures. This test program confirmed that lower propeller noise levels are produced in forward flight than under static conditions and that the most significant reductions occur at the midfrequencies which dominate perceived and A-weighted noise levels.

Pegg, R. J.↗
NASA NTRS1976

Progress report on propeller aircraft flyover noise research

Initial results of a program to investigate the sources of noise in unshrouded propellers under forward flight conditions are reported. Tests were conducted using a three-blade full-scale instrumented propeller mounted on a twin-engine aircraft. Measurements included (1) far-field noise at fixed ground stations and at two aircraft wing tip locations, (2) blade surface pressures at seven locations on one of the propeller blades, (3) atmospheric turbulence encountered by the aircraft in flight, and (4) aircraft operating conditions. The results confirm that significantly lower levels of propeller noise are produced in forward flight than at static conditions. It is tentatively concluded that propeller noise generation in flight may be dominated by steady loading at blade passage frequency, but at higher frequencies unsteady loading due to interaction with natural atmospheric turbulence may be the dominant mechanism of noise generation. Under static conditions the total noise signature appears to be the result of interaction of the propeller with persistent turbulent eddies passing through the propeller disk.

Metzger, F. B.↗
NASA NTRS1976

Insights into the nature and control of rotor noise

The dynamics of four important farfield rotating blade noise sources are summarized and techniques for noise reduction are discussed. These four noise areas include the role of unsteady blade surface loads on rotational noise, the effect of turbulent inflow on the radiated broadband noise of an airfoil, the influence of the trailing vortex on impulsive noise and tail rotor noise, and the effect of blade geometry on high-speed impulsive noise. These noise mechanisms occur to varying degrees on both helicopter rotors and propellers. Considerable theoretical work was done in the area of high-speed impulsive noise resulting from the geometry of the rotating blade system. Both model and full-scale experimental correlation of helicopter and propeller high-speed noise are presented. The effect of blade number and airfoil thickness distribution in reducing the high-speed noise is shown.

Pegg, R. J.↗
NASA NTRS1976

A parametric model study of the noise generated by the aerodynamic interaction of the tail rotor with the wake of the main rotor

Wind tunnel tests were conducted to determine the influence of various parameters on the noise produced by the interaction of the main rotor wake with the tail rotor. Parameters found to be of significance were the location of the main rotor vortex interaction on the tail rotor disk, the direction of rotation of the tail rotor, the lateral tail rotor-fin spacing, and the operating mode of the tail rotor. Of lesser importance were the main rotor thrust coefficient, longitudinal spacing between rotors, and tail rotor-to-main rotor rotational speed ratios. Analysis of the interaction noise characteristics using a simplified representation of the aerodynamic phenomena occurring during the interaction showed that existing predictive techniques could be modified and extended to predict the pertinent noise characteristics.

White, R. P., Jr.↗
NASA NTRS1975

Design and preliminary tests of a blade tip air mass injection system for vortex modification and possible noise reduction on a full-scale helicopter rotor

Full-scale tests were conducted on the Langley helicopter rotor test facility as part of a study to evaluate the effectiveness of a turbulent blade tip air mass injection system in alleviating the impulsive noise (blade slap) caused by blade-vortex interaction. Although blade-slap conditions could not be induced during these tests, qualitative results from flow visualization studies using smoke showed that the differential velocity between the jet velocity and the rotor tip speed was a primary parameter controlling the vortex modification.

Pegg, R. J.↗
NASA NTRS1975

Thickness noise of helicopter rotors at high tip speeds

A new formulation of helicopter rotor thickness, noise for hover and forward flight, is discussed. The parameters required for this formulation are rotor motion, planform and airfoil thickness distribution. A computer program has been developed to calculate the pressure signature due to blade thickness for a helicopter in arbitrary motion. Comparison with high-speed helicopter tests shows good agreement with calculations when the observer is in or near the horizontal plane in which the rotor disk lies. Characteristics of thickness noise are illustrated by numerical examples indicating strongly that the high-speed blade slap may be due primarily to the thickness effect. The methods of Deming and Arnoldi are discussed as the special cases of this technique.

Farassat, F.↗
NASA NTRS1975

Summary of results indicating the beneficial effects of rotor vortex modification

The possibility of reducing blade-slap noise and high-frequency air loads and of increasing performance by tip air mass injection (TAMI) is investigated. The discussion is limited to two types of TAMI: chordwise injection with air injected at the blade tip in a chordwise direction and spanwise injection with air injected in a spanwise direction. Experimental and analytical results indicate that a properly designed TAMI system can restructure the near field characteristics of a concentrated vortex that trails off the tip of a lifting surface, that the tip vortex is spread by the application of chordwise TAMI, that mixing exists between the injected air mass and the vortex flow which enhances vortex decay, that the net power requirements to implement the system on operational helicopters are within acceptable levels, that maximum drop of noise level reductions of about 25 dB can be achieved, and that a decrease in the drag induced by the tip vortex in a spanwise TAMI system can be obtained by restructuring the vortex as it forms along the airfoil chord and by moving the vortex farther outboard of the tip.

White, R. P., Jr.↗
NASA NTRS1975

Thickness Noise of Helicopter Rotors at High Tip Speeds

A new formulation of helicopter rotor thickness, noise for hover and forward flight, is discussed. The parameters required for this formulation are rotor motion, planform and airfoil thickness distribution. A computer program has been developed to calculate the pressure signature due to blade thickness for a helicopter in arbitrary motion. Comparison with high-speed helicopter tests shows good agreement with calculations when the observer is in or near the horizontal plane in which the rotor disc lies. Characteristics of thickness noise are illustrated by numerical examples indicating strongly that the high-speed blade slap may be due primarily to the thickness effect. The methods of Deming and Arnoldi are discussed as the special cases of this technique.

Farassat, F.↗
NASA NTRS1974

Flyover noise characteristics of a tilt-wing V/STOL aircraft (XC-142A)

A field noise measurement investigation was conducted during the flight testing of an XC-142A tilt-wing V/STOL aircraft to define its external noise characteristics. Measured time histories of overall sound pressure level show that noise levels are higher at lower airspeeds and decrease with increased speed up to approximately 160 knots. The primary noise sources were the four high-speed, main propellers. Flyover-noise time histories calculated by existing techniques for propeller noise prediction are in reasonable agreement with the experimental data.

Pegg, R. J.↗
NASA NTRS1974

Comparison of acoustic performance of five muffler configurations on a small helicopter

A field noise measurement program has been conducted on a standard Bell 47 series helicopter and on one that had been modified with specially designed, airframe-mounted mufflers to reduce the engine exhaust noise. The purpose of the study was to evaluate the acoustic performance of five experimental exhaust muffler configurations for a helicopter reciprocating engine in an operational environment. All muffler configurations produced beneficial engine exhaust noise reductions but some configurations were markedly better than others. Flyover noise results indicated that maximum overall noise reductions of approximately 8 db were obtained with the various mufflers. The rotor noise was judged to be the dominant noise component for the muffler-equipped helicopters whereas the engine noise was the dominant component for the basic configuration.

Pegg, R. J.↗
NASA NTRS1974

The prediction of rotor rotational noise using measured fluctuating blade loads

In tests conducted at the NASA Langley Research Center Helicopter Rotor Test Facility, simultaneous measurements of the high-frequency fluctuating aerodynamic blade loads and far-field radiated noise were made on a full-scale, nontranslating rotor system. After their characteristics were determined, the measured blade loads were used in an existing theory to predict the far-field rotational noise. A comparison of the calculated and measured rotational noise is presented with specific attention given to the effect of blade loading coefficients, chordwise loading distributions, blade loading phases, and observer azimuthal position on the predictions.

Hosier, R. N.↗
NASA NTRS1974

The noise environment of a school classroom due to the operation of utility helicopters

Noise measurements under controlled conditions have been made inside and outside of a school building during flyover operations of four different helicopters. The helicopters were operated at a condition considered typical for a police patrol mission. Flyovers were made at an altitude of 500 ft and an airspeed of 45 miles per hour. During these operations acoustic measurements were made inside and outside of the school building with the windows closed and then open. The outside noise measurements during helicopter flyovers indicate that the outside db(A) levels were approximately the same for all test helicopters. For the windows closed case, significant reductions for the inside measured db(A) values were noted for all overflights. These reductions were approximately 20 db(A); similar reductions were noted in other subjective measuring units. The measured internal db(A) levels with the windows open exceeded published classroom noise criteria values; however, for the windows-closed case they are in general agreement with the criteria values.

Hilton, D. A.↗