Engineering Papers⌕ Search

Engineering topics

Patterson, Tate

Publications and source records attributed to Patterson, Tate.

15 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Creep-Fatigue Properties of Additional 316H PM-HIP Materials Fabricated from Different Powder Compositions and Processing Routes

The process of powder metallurgy (PM) hot isostatic pressing (HIP) works by consolidating powdered materials at relatively high temperature and pressure to form near-net-shaped components. Ideally, PM-HIP production methods can reduce component lead time and improve designs for high-temperature reactors and/or microreactors. To introduce PM-HIP into Section III, Division 5 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, it is necessary to show adequate material properties regarding creep, high-temperature low-cycle fatigue, and creep fatigue. However, prior work has shown that the creep-fatigue cycles to failure for PM-HIP 316H stainless steel are greatly reduced compared to the conventional, wrought product. This work continued creep-fatigue analysis on a 316H stainless steel with lower oxygen and nitrogen contents and at different HIP parameters than previously analyzed. The objective was to better understand what is causing the reduced PM-HIP 316H performance so improvements can be made PM-HIP 316H creep-fatigue lifetimes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Electric field enhanced diffusion welding of alloy 617: Microstructural characteristics and mechanical properties

This study investigated the microstructural characteristics and mechanical behavior of diffusion welded nickel-based Alloy 617 obtained by electric field-assisted sintering (EFAS) using various parameters. The interfacial microstructure exhibited different characteristics including good grain boundary (GB) migration across the interface in the samples diffusion-welded at 1100 °C and a flat interface in the samples joined at 1000 °C and 1050 °C. The interface consisted of fine Al 2 O 3 oxides, while precipitation of interfacial M 23 C 6 carbides was not observed. Grain boundaries migrated across the Al 2 O 3 oxides, leaving these oxides within the grains. Graded grain size was observed, with grain coarsening being more significant near the sample surface due to the temperature gradient induced by EFAS. Tensile testing revealed that the specimens fractured in the matrix away from the interface, indicting strong diffusion-welded joints. Further, the peak tensile strength of 807 MPa was obtained in the samples welded at 1000 °C due to minimal grain growth. The materials obtained at 1100 °C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed alternating high and low strain segments in the samples produced at 1000 °C and 1050 °C, indicating that the flat interfaces with no GB migration were less ductile compared to the matrix. A greater strain uniformity was observed along the bond interfaces with improved GB migration. The hardness reduced near the sample surfaces due to enlarged grains induced by temperature gradient. This study demonstrates that GB migration and enhanced mechanical strength can be achieved in diffusion-welded Alloy 617.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Evaluation of Directed Energy Deposition and Laser Powder Bed Fusion Nickel-Based Alloys Process Application Envelopes Based on Performance, Process Economics, Supply Chain Risks, and Reactor-Specific Targeted Components

The goal of the Advanced Materials and Manufacturing Technologies (AMMT) program is to accelerate the deployment of new materials and manufacturing technologies into advanced nuclear-related systems. Although 316H stainless steel fabricated by laser powder bed fusion (LPBF) has already been identified as an alloy that could have a significant effect on various reactor technologies, many other materials and manufacturing techniques are being evaluated. Nickel-based alloys typically offer higher-temperature capabilities compared with advanced stainless steels, and previous reports looked at three Ni-based alloy categories: low-Co alloys with a potential use close to the reactor core; high-temperature, high-strength alloys; and molten salt–compatible alloys. Due to the increasing interest in the low Co 625 alloy for nuclear applications, the alloy was compared at the Oak Ridge National Laboratory (ORNL) with 617, 230, two high-temperature, high-strength solution-strengthened alloys. Hot cracking could not be suppressed for alloy 230, and it was shown that these cracks, which were elongated along the build direction (BD), had a drastic effect on the ductility of alloy 230 at room temperature when specimens were machined perpendicular to the BD. Cracking was not as significant for alloy 617, but still led to significant variation in ductility at room temperature along the build direction. On the contrary, LPBF printing of crack-free alloy 625 was achieved using similar printing parameters, and the alloy looks like a very promising candidate for various reactor technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Nuclear Structural Component Relevant Properties of Nickel-Based Alloys Produced via Additive Manufacturing

Idaho National Laboratory initiated examination of nickel-based alloys manufactured via three different additive manufacturing methods for potential applications in nuclear, high temperature structural components. The three methods analyzed included laser powder bed fusion, blown powder laser directed energy deposition, and wire-fed gas metal arc directed energy deposition. With the rapid push towards additive manufacturing, codes do not exist that definitively define what is or is not tolerable for each process and application, such as with conventional, wrought products. This report contains the initial work to understand possible manufacturing methods for high temperature alloys, and specifically, void formation, microstructure evolution, corrosion, and mechanical properties. To generate mechanical test data, specimens were tested irrespective of voids and microstructures were analyzed to better understand how to negate/improve these issues. The preliminary results showed major decreases in mechanical performance for material tested. Test specimens will continue to be produced to further improve each additive manufacturing processes, quantify void acceptance, and better understand the most suitable high temperature alloys receptive to additive manufacturing and high temperature nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An Initial Evaluation of the Elevated-Temperature Cyclic Properties of Optimized 316H Stainless Steel Fabricated by Powder Metallurgy Hot Isostatic Pressing

Powder metallurgy hot isostatic pressing (PM-HIP) is a mature advanced manufacturing technology, which can consolidate metallic powder under high temperature and pressure to generate near-net shape components. This process can lower production costs and reduce component lead times for nuclear reactor construction and can be readily deployed in the near term for microreactor components because of their smaller size. The purpose of this work is to continue the evaluation of elevated-temperature cyclic material properties for PM-HIP 316H stainless steel. Prior scoping results have shown that the commercially procured PM-HIP stainless-steel materials have reduced creep-fatigue performance compared to wrought 316 stainless steels. To better understand how PM-HIP processed material properties compare to traditional manufacturing methods, additional billets of PM-HIP 316H stainless steel were procured and tested. This testing is necessary to understand how elevated-temperature properties are influenced by the PM-HIP process and what data are needed for incorporating PM HIP 316H into the American Society of Mechanical Engineers Boiler Pressure Vessel Code, Section III, Division 5 for high temperature reactor construction. Specifically, an additional PM-HIP 316H stainless steel billet with lower oxygen and nitrogen concentrations was fabricated by the Nuclear Advanced Manufacturing Research Centre of the United Kingdom and tested to understand if elevated-temperature cyclic properties can be improved. The creep-fatigue resistance of the material from this new billet did not show appreciable improvement compared to prior testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Assessment of UTP A 2133 Mn as a Matching Filler Metal for Alloy 800H in Section III, Division 5 Applications

Six alloys are qualified in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC) for elevated-temperature nuclear components. Due to reactor design alloy restrictions and motivation to improve operational efficiency and plant lifetimes, it is necessary to maximize the usefulness of qualified alloys. One of these alloys is Alloy 800H, which is qualified for a maximum temperature of 760°C and a maximum 300,000-hour service life. However, the welding filler metals qualified to join Alloy 800H have stress rupture factors that reduce the allowable weldment strength by factors as low as 0.59 times the Alloy 800H base metal. In an effort to improve the weldment creep-rupture performance, or to increase the stress reduction factor, non-code qualified filler metals are under investigation by the Department of Energy?s Advanced Reactor Technologies program. For this investigation, UTP A 2133 Mn filler metal (Fe-Cr-Ni-Mn-Nb) was used to join 0.5 in. thick Alloy 800H plate to demonstrate passing an ASME BPVC Section IX weld qualification. The multi-pass, pulsed GTAW process showed successful weld qualification results, and additional property measurements were conducted to compare previous analyses of Alloy 82 and Alloy 617 filler metals. Future work will evaluate the cross-weld creep-rupture performance of the UTP A 2133 Mn in comparison to Alloy 82 and Alloy 617 filler metals.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Enhanced diffusion bonding of alloy 617 using electric field-assisted sintering

The development of compact heat exchangers (CHXs) has gained increasing interest in many industries owing to their high thermal efficiency and reduced size. Diffusion bonding (DB) is an advantageous technique for fabricating CHXs. Alloy 617 is a candidate for manufacturing CHXs for high-temperature advanced nuclear reactors due to its elevated-temperature properties. Previous endeavors in DB of Alloy 617 were conducted by hot pressing (HP), which reported precipitates at the diffusion-bond interface, limited grain boundary (GB) migration, and significantly reduced high-temperature mechanical properties. To overcome these challenges, this study investigated DB of Alloy 617 using electric field-assisted sintering (EFAS). Stacks composed of three sheets were bonded with EFAS using different temperatures, pressures, and hold times. DB using HP as the zero-current analog of EFAS was also performed for comparison. The result shows that Cr- and Mo-rich precipitates were formed at the interface of the hot-pressed samples. The electric current and temperature in EFAS play a significant role in precipitation and GB migration. The electric current coupled with correct temperatures can effectively prevent precipitate formation at the interface and achieve excellent GB migration. Nanoscale Al-rich oxide was formed at the interface of the samples made by both HP and EFAS, but grain boundaries can ignore the nanoscale Al-oxide and migrate across the interface. The temperature, pressure, and hold time also affected diffusion. The temperature is a prerequisite for a successful GB migration, and GB migration can be enhanced by increasing pressure and hold time.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of Surveillance Test Articles with Reduced Dimensions and Material Volumes to Support MSR Materials Degradation Management

This report details the efforts toward developing new surveillance test article designs with reduced dimensions and material volumes to support materials surveillance technology development for advanced reactors. Two fabrication methods for the surveillance test articles are described. Welded test articles were fabricated with 316H and A617 materials, and interlocking test articles were fabricated using A709 and titanium-zirconium-molybdenum (TZM). The preliminary results demonstrate the successful design and testing of the flat surveillance test articles. The report also describes ongoing efforts to use an induction heating test setup to increase the heat up and cool down rates in testing the surveillance test articles. A brief description of the planned FY-24 work is provided.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

ASME Code Qualification Plan for LPBF 316 SS

This report describes a plan to qualify laser powder bed fusion (LPBF) 316 stainless steel for use with the American Society of Mechanical Engineers (ASME) Boiler & Pressure Vessel Code Section III, Division 5 rules for metallic components in high temperature nuclear reactors. Accomplishing this goal would make the material and manufacturing process available to vendors for inclusion in the next generation of advanced, high temperature reactors. The general approach adopted here is to treat LPBF 316 as if it was a completely new material and to develop a plan to qualify the material according to the current ASME practices. One key goal of this work is to explore and develop accelerated qualification approaches that might reduce the time required to qualify new materials by reducing the need for long term testing. However, the qualification plan here does not employ any accelerated qualification approaches to provide a limiting, bounding description of the number, duration, and types of testing required to qualify LPBF 316 without such techniques and to describe a comprehensive dataset that could be used to explore and validate accelerated qualification approaches in the future. The report addresses the fundamental challenges to qualifying Advanced Manufacturing (AM) materials for high temperature applications and summarizes the ASME Section III qualification process as well as current efforts to qualify LBPF and DED 316 for low temperature applications. The report then discusses specific issues, both material and logistical, related to qualifying PBF 316 steel. The final chapters of the report describe a complete test plan designed to generate sufficient data to qualify the material as well as a data management plan for how to store and manage the data to eventually provide the test data packaged needed to qualify the material with ASME.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

A Summary of the Microstructural Characterization Results for the A709 Commercial Heats

To improve high temperature strength for advanced nuclear reactors, it is necessary to qualify additional structural materials for introduction into the American Society of Mechanical Engineers (AMSE) Boiler and Pressure Vessel Code (BPVC). Specifically, Alloy 709 was identified as a material for Sodium-cooled Fast Reactors to enhance time-dependent mechanical properties compared to 316H stainless steel, a code qualified high temperature alloy. Idaho National Laboratory (INL) and Oak Ridge National Laboratory (ORNL) performed initial microstructure and mechanical property testing on a third, commercial heat of Alloy 709 stainless steel. The Alloy 709 plate was produced by Allegheny Technology Inc. (ATI) and in the solution annealed condition. The chemical composition was within the limits for an American Society of Testing and Materials (ASTM) A213 specification for seamless tube for material UNS S31025. Grain size was measured as an average ASTM size of 6.5, which was larger than the ASTM 7 required according to ASTM A213 for seamless tube. The chemical composition was within the limits for an ASTM A213, and the room temperature tensile tests and hardness data met ASTM A213 specifications. Creep-fatigue results showed similar behavior to previous heats of Alloy 709.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗