Engineering Papers⌕ Search

Engineering topics

Patterson, Steven

Publications and source records attributed to Patterson, Steven.

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electronics module with raceway and submodules

Systems and methods for providing an electronics module including a raceway for mounting submodules and establishing electrical communication with said submodules. The raceway comprises a base structure and a conductive trace formed by a conductive plating process. Connection pads on the raceway are configured to receive connection nodes of the submodules for providing a continuous electrical connection between the raceway and the submodules for electrical communication and power transmission.

Eickbush, Ryan J.↗
DOE OSTI2023

One-Component, Vinyl-Functional Fluorosilicone Pastes for Direct Ink Write Additive Manufacturing

In this study, one-component (“all-in-one”) fluorosilicone pastes specifically designed for application in direct ink write (DIW) additive manufacturing (AM) have been developed. They consist of vinyl-functional, methyltrifluoropropyl-containing (MeTfpS) terpolysiloxane base polymer(s), hydrosilyl-functional cross-linker(s), UV-sensitive hydrosilylation catalyst, thixotropic additive, and trimethylsilylated fumed silica filler, with other additives that are optional. Their base polymers were completely amorphous and linear, with molecular weights (M n ) ranging from approximately 7000 to 50,000 and specifically targeted for the viscosity range ideal for DIW. These polymers were prepared by anionic ring-opening polymerizations (A-ROP) of appropriate mixtures of cyclic siloxanes initiated by oligomeric, difunctional tetramethylammonium silanolate in the presence of a difunctional tetramethyldivinyldisiloxane end-blocker and molecular weight regulator. Two series of these terpolymers were prepared: one containing 5 mol % MeTfpS repeat units but varying degrees of polymerization (DP) from 80 to 600 and the other containing 5, 10, and 15 mol % MeTfpS at a constant DP of 600. All polymers contained mostly random distributions of MeTfpS repeat units. The pastes were prepared by speed-mixing, ready for use in DIW, they exhibited ideal thixotropy, long-term (over a year) rheological stability, and can be quickly (within seconds) and permanently cured by room-temperature, UV-activated hydrosilylation in air. The resulting elastomers showed base polymer molecular weight- and composition-dependent stress-induced crystallization (SIC) at higher molecular weights and lower trifluoropropyl contents and tunable Shore A hardness (30A–40A) typical for soft polysiloxane rubbers. Preliminary DIW tests indicated excellent printability with high precision of printed shapes and clearly present these one-component pastes as prime candidates for simple and practical printing of silicone elastomer objects.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Temporally Stable Supramolecular Polymeric Salts Enabling High-Performance 3D All-Aromatic Polyimide Lattices

Vat photopolymerization (VP) Additive Manufacturing (AM), in which UV light is selectively applied to cure photo-active polymers into complex geometries with micron-scale resolution, has a limited selection of aliphatic thermoset materials that exhibit relatively poor thermal performance. Ring-opening dianhydrides with acrylate-containing nucleophiles yielded diacrylate ester-dicarboxylic acids that enabled photo-active polyimide (PI) precursors, termed polysalts, upon neutralization with an aromatic diamine in solution. In situ FTIR spectroscopy coupled with a solution and photo-rheological measurements revealed a previously unknown time-dependent instability of 4,4'-oxydianiline (ODA) polysalts due to an aza-Michael addition. Replacement of the electron-donating ether-containing diamine with an electron withdrawing sulfone-containing monomer, e.g., 4,4'-diaminodiphenyl sulfone (DDS), prohibited the aza-Michael addition of the aromatic amine to the activated acrylate double bond. Novel DDS polysalt photocurable solutions are similarly analyzed and validated long-term stability, which enabled reproducible printing of polyimide organogel intermediates. Subsequent VP AM afforded 3-dimensional (3D) structures of intricate complexity and excellent surface finish, as demonstrated with scanning electron microscopy. In addition, the novel PMDA-HEA/DDS solution enabled the production of the first beam latticed architecture comprised of all-aromatic polyimide. Finally, the versatility of a polysalt platform for multi-material printing is further demonstrated by printing parts with alternating polysalt compositions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Direct ink write multi-material printing of PDMS-BTO composites with MWCNT electrodes for flexible force sensors

Here, with recent advances of additive manufacturing technology, direct ink write (DIW) printing has allowed to incorporate multi-material printing of various materials with freedom of design and complex geometric shapes to complete functional sensors in a one-step fabrication. This paper introduces the use of DIW 3D printing of polydimethylsiloxane (PDMS) with barium titanate (BTO) filler as stretchable composites with tunable piezoelectric properties that can be used for force sensors applications. To improve the bonding between stretchable piezoelectric composites and electrodes, multi-walled carbon nanotubes was included in the fabrication of electrodes at a fixed ratio of 11 wt. %. The alignment of the BTO dipoles was achieved through corona poling method, which applies an electric charge on the surface layer of the functional material, aligning the dipoles in the desired direction and thus gaining the piezoelectricity. Different BTO mixing ratios (10–50 wt. %) were evaluated in order to obtain tunable piezoelectric properties and compare the sensitivity with respect their elastic properties. Tensile testing and piezoelectric testing were carried out to characterize mechanical and piezoelectric properties. Results showed that fabricated PDMS with 50 wt. % BTO gave the highest piezoelectric coefficient (d 33 ) of 11.5 pC N -1 and with an output voltage of 385 mV under compression loading of >200 lbF. This demonstrates feasibility of using multi-material DIW printing to fabricate piezoelectric force sensors with integrated electrodes in one-step without compromising the flexibility of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Additive Manufacturing of Controlled Porous Elastomeric Nanocomposites for Enhanced Sensing Function

Sensors manufactured using piezoresistive elastomeric nanocomposites have a wide range of applications in many fields such as structural health monitoring, robotics, and biomedical industries. Additive manufacturing of these sensors, achieved using Direct Ink Writing (DIW), has provided numerous advantages including increased sensitivity and the fabrication of complex geometry. However, solid sensors manufactured either additively or using conventional methods, display a greater level of hysteresis, especially at strains higher than 10%, which limits their sensitivity. The solid sensors also display a greater level of piezoresistive relaxation where the resistance change with time either in a static or dynamic loading environment. Porosity can be introduced in the form of varying infill patterns and densities to reduce bulk material effects. In this paper, a lattice structure with four infill densities are investigated, and the samples are printed using a grid infill pattern. The fabricated samples are characterized using a scanning electron microscope (SEM) to validate the microstructural features and layer bonding. The pressure-sensing capability of each sensor is investigated using cyclic compression loading at various strain levels. Sensing results show that an increase in sensitivity, as well as a decrease in hysteresis with an increase in porosity, compared to solid samples (100% in-fill). The highest porosity was measured to be 62.3% with a corresponding 112% increase in the gauge factor compared to the solid bulk. These results indicate that introducing porosity using DIW is a sensible strategy to improve the piezoresistive performance of nanocomposites and to allow for the tunability of sensing capacity in pressure sensors

Sukati, Musa↗
DOE OSTI2019

Self-Complementary Multiple Hydrogen-Bonding Additives Enhance Thermomechanical Properties of 3D-Printed PMMA Structures

Nonbonded interactions provide a way to guide the assembly and alter the physical properties of soft polymeric materials. The self-complementary hydrogen-bonding interactions conveyed through polymeric additives dramatically enhance thermomechanical properties of poly(methyl methacrylate) (PMMA) specimens printed by fused filament fabrication (FFF). Random copolymer additives composed of methyl methacrylate (MMA) and a methacrylate monomer containing 2-ureido-4-pyrimidone (UPy) pendant group (UPyMA), which self-dimerize through quadruple hydrogen-bonding interactions, were incorporated at 1 wt % in a high molecular weight PMMA matrix. Results from dynamic mechanical analysis measurements made in the glassy regime show that as the UPyMA comonomer content in the p(MMA-r-UPyMA) copolymer additive increases up to 5 mol %, there is a 50% increase in Young’s modulus and a 62% increase in the storage modulus. Concomitantly, there is an 85% increase in ultimate tensile strength and a 100% increase in tensile modulus. Additionally, rheology measurements indicate that at temperatures well above the glass transition temperature, the storage modulus and complex viscosity of the multicomponent blends are unaffected by the incorporation of p(MMA-r-UPyMA) additives, regardless of the UPyMA content. In aggregate, these results suggest that using reversible, nonbonded intermolecular interactions, such as multidentate hydrogen bonding, provides a novel route to overcome the mechanical property limitations of FFF-printed materials without affecting melt processability.

36 MATERIALS SCIENCE↗