Engineering topics

Patterson, Richard L.

Publications and source records attributed to Patterson, Richard L..

68 records · Page 4

NASA NTRS1995

The 77 K operation of a multi-resonant power converter

The liquid-nitrogen temperature (77 K) operation of a 55 W, 200 kHz, 48/28 V zero-voltage switching multi-resonant dc/dc converter designed with commercially available components is reported. Upon dipping the complete converter (power and control circuits) into liquid-nitrogen, the converter performance improved as compared to the room-temperature operation. The switching frequency, resonant frequency, and the characteristic impedance did not change significantly. Accordingly, the zero-voltage switching was maintained from no-load to full-load for the specified line variations. Cryoelectronics can provide high density power converters, especially for high power applications.

Ray, Biswajit↗

NASA NTRS1995

Liquid Nitrogen Temperature Operation of a Switching Power Converter

The performance of a 42/28 V, 175 W, 50 kHz pulse-width modulated buck dc/dc switching power converter at liquid nitrogen temperature (LNT) is compared with room temperature operation. The power circuit as well as the control circuit of the converter, designed with commercially available components, were operated at LNT and resulted in a slight improvement in converter efficiency. The improvement in power MOSFET operation was offset by deteriorating performance of the output diode rectifier at LNT. Performance of the converter could be further improved at low temperatures by using only power MOSFET's as switches. The use of a resonant topology will further improve the circuit performance by reducing the switching noise and loss.

Ray, Biswajit↗

NASA NTRS1994

Method of locating ground faults

The present invention discloses a method of detecting and locating current imbalances such as ground faults in multiwire systems using the Faraday effect. As an example, for 2-wire or 3-wire (1 ground wire) electrical systems, light is transmitted along an optical path which is exposed to magnetic fields produced by currents flowing in the hot and neutral wires. The rotations produced by these two magnetic fields cancel each other, therefore light on the optical path does not read the effect of either. However, when a ground fault occurs, the optical path is exposed to a net Faraday effect rotation due to the current imbalance thereby exposing the ground fault.

Patterson, Richard L.↗

NASA NTRS1993

Minimize system cost by choosing optimal subsystem reliability and redundancy

The basic question which we address in this paper is how to choose among competing subsystems. This paper utilizes both reliabilities and costs to find the subsystems with the lowest overall expected cost. The paper begins by reviewing some of the concepts of expected value. We then address the problem of choosing among several competing subsystems. These concepts are then applied to k-out-of-n: G subsystems. We illustrate the use of the authors' basic program in viewing a range of possible solutions for several different examples. We then discuss the implications of various solutions in these examples.

Suich, Ronald C.↗

NASA NTRS1991

Reliability and cost: A sensitivity analysis

In the design phase of a system, how a design engineer or manager choose between a subsystem with .990 reliability and a more costly subsystem with .995 reliability is examined, along with the justification of the increased cost. High reliability is not necessarily an end in itself but may be desirable in order to reduce the expected cost due to subsystem failure. However, this may not be the wisest use of funds since the expected cost due to subsystem failure is not the only cost involved. The subsystem itself may be very costly. The cost of the subsystem nor the expected cost due to subsystem failure should not be considered separately but the total of the two costs should be maximized, i.e., the total of the cost of the subsystem plus the expected cost due to subsystem failure.

Suich, Ronald C.↗

NASA NTRS1991

k-out-of-n:G systems - Some cost considerations

The authors provide a tool that an engineer designing a subsystem can use to decide between one subsystem and a more reliable but more costly one. The authors provide methods for selecting redundancy levels in k-out-of-n:G systems in order to minimize particular cost considerations where the k-out-of-n:G system is a subsystem of a major system. The n and k are chosen to minimize the total cost of the subsystem plus the average loss due to subsystem failure. A BASIC program is available to determine the n and k which find this minimum. Five loss functions are considered, and illustrations are given.

Suich, Ronald C.↗

NASA NTRS1991

Balancing reliability and cost to choose the best power subsystem

A mathematical model is presented for computing total (spacecraft) subsystem cost including both the basic subsystem cost and the expected cost due to the failure of the subsystem. This model is then used to determine power subsystem cost as a function of reliability and redundancy. Minimum cost and maximum reliability and/or redundancy are not generally equivalent. Two example cases are presented. One is a small satellite, and the other is an interplanetary spacecraft.

Suich, Ronald C.↗

NASA NTRS1991

Fiber-optic sensors for aerospace electrical measurements: An update

Fiber-optic sensors are being developed for electrical current, voltage, and power measurements in aerospace applications. These sensors are presently designed to cover ac frequencies from 60 Hz to 20 kHz. The current sensor, based on the Faraday effect in optical fiber, is in advanced development after some initial testing. Concentration is on packaging methods and ways to maintain consistent sensitivity with changes in temperature. The voltage sensor, utilizing the Pockels effect in a crystal, has excelled in temperature tests. This paper reports on the development of these sensors, the results of evaluation, improvements now in progress, and the future direction of the work.

Patterson, Richard L.↗

NASA NTRS1991

Balancing reliability and cost to choose the best power subsystem

The justification of the increased cost of a more reliable power subsystem is discussed. A mathematical model is presented for computing total spacecraft subsystem cost including both the basic subsystem cost and the expected cost due to the failure of the subsystem. This is then used to determine the power subsystem cost as a function of reliability and redundancy. Minimum cost and maximum reliability and/or redundancy are not generally equivalent. Two example cases are presented. One is a small satellite, and the other is an interplanetary spacecraft.

Suich, Ronald C.↗

NASA NTRS1991

Fiber-optic sensors for aerospace electrical measurements - An update

The authors report the progress made on the development of aerospace current and voltage sensors which use fiber-optic and optical sensing heads. These sensors are presently designed to cover ac frequencies from 60 Hz to 20 kHz. The current sensor, based on the Faraday effect in optical fiber, is in advanced development after some initial testing. The emphasis is on packaging methods and ways to maintain consistent sensitivity with changes in temperature. The voltage sensor, utilizing the Pockels effect in a crystal, has excelled in temperature tests. The authors report on the development of these sensors. The authors also relate the technology used in the sensors, the results of evaluation, improvements being made, and the future direction of the work.

Patterson, Richard L.↗

NASA NTRS1990

A fiber-optic current sensor for aerospace applications

A robust, accurate, broadband, alternating current sensor using fiber optics is being developed for space applications at power frequencies as high as 20 kHz. It can also be used in low and high voltage 60-Hz terrestrial power systems and in 400-Hz aircraft systems. It is intrinsically electromagnetic interference (EMI) immune and has the added benefit of excellent isolation. The sensor uses the Faraday effect in optical fiber and standard polarimetric measurements to sense electrical current. The primary component of the sensor is a specially treated coil of single-mode optical fiber, through which the current carrying conductor passes. Improved precision is accomplished by temperature compensation by means of signals from a novel fiber-optic temperature sensor embedded in the sensing head. The technology used in the sensor is examined and the results of precision tests conducted at various temperatures within the wide operating range are given. The results of early EMI tests are also given.

Patterson, Richard L.↗

NASA NTRS1990

A fiber-optic current sensor for aerospace applications

A robust, accurate, broad-band, alternating current sensor using fiber optics is being developed for space applications at power frequencies as high as 20 kHz. It can also be used in low and high voltage 60 Hz terrestrial power systems and in 400 Hz aircraft systems. It is intrinsically electromagnetic interference (EMI) immune and has the added benefit of excellent isolation. The sensor uses the Faraday effect in optical fiber and standard polarimetric measurements to sense electrical current. The primary component of the sensor is a specially treated coil of single-mode optical fiber, through which the current carrying conductor passes. Improved precision is accomplished by temperature compensation by means of signals from a novel fiber-optic temperature sensor embedded in the sensing head. The technology contained in the sensor is examined and the results of precision tests conducted at various temperatures within the wide operating range are given. The results of early EMI tests are also given.

Patterson, Richard L.↗

NASA NTRS1990

How much redundancy: Some cost considerations, including examples for spacecraft systems

How much redundancy should be built into a subsystem such as a space power subsystem. How does a reliability or design engineer choose between a power subsystem with 0.990 reliability and a more costly subsystem with 0.995 reliability. How does the engineer designing a power subsystem for a satellite decide between one power subsystem and a more reliable but heavier power subsystem. High reliability is not necessarily an end in itself. High reliability may be desirable in order to reduce the statistically expected loss due to a subsystem failure. However, this may not be the wisest use of funds since the expected loss due to subsystem failure is not the only cost involved. The subsystem itself may be very costly. The cost of the subsystem or the expected loss due to subsystem failure may not be considered separately. Therefore, the total of the two costs is minimized, i.e., the total of the cost of the subsystem plus the expected loss due to subsystem failure. A specific type of redundant system is considered, called a k-out-of-n: G subsystem. Such a subsystem has n modules, of which k are required to be good for the subsystem to be good. Five models are discussed which can be applied in the design of a power subsystem to select the unique redundancy method which will minimize the total of the cost of the power subsystem plus the expected loss due to the power subsystem failure. A BASIC computer program is available.

Suich, Ronald C.↗

NASA NTRS1990

A fiber-optic current sensor for aerospace applications

A robust, accurate, broadband, alternating current sensor using fiber optics is being developed for space applications at power frequencies as high as 20 kHz. It can also be used in low- and high-voltage 60-Hz terrestrial power systems and in 400-Hz aircraft systems. It is intrinsically EMI (electromagnetic interference) immune and has the added benefit of excellent isolation. The sensor uses the Faraday effect in optical fiber and standard polarimetric measurements to sense electrical current. The primary component of the sensor is a specially treated coil of single-mode optical fiber, through which the current carrying conductor passes. Improved precision is accomplished by temperature compensation by means of signals from a fiber-optic temperature sensor embedded in the sensing head. The authors report on the technology contained in the sensor and also relate the results of precision tests conducted at various temperatures within the wide operating range. The results of early EMI tests are shown.

Patterson, Richard L.↗