Engineering Papers⌕ Search

Engineering topics

Patnaik, Sobhan

Publications and source records attributed to Patnaik, Sobhan.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Evaluating the diffusion of Kr in UO 2 and ADOPT TM using time-of-flight elastic recoil detection analysis (ToF-erda)

A combination of 300 keV 84 Kr ion implantation and Time-of-Flight Elastic Recoil Detection Analysis is utilized to investigate the diffusion of Kr in UO 2 and ADOPT TM fuels. Composition depth-profiles on the nanometer scale were obtained, both for as-implanted samples and after annealing at 800°C for 1 hour. Observed drifts in the 84 Kr profiles could be associated with short-range diffusion mechanisms. The approach employed here provides the possibility to make direct comparisons with atomistic scale modelling data, and can be of service as a separate effect test in line with the Accelerated Fuel Qualification initiative.

ADOPT UO2↗
DOE OSTI2024

Enhanced steam oxidation resistance of uranium nitride nuclear fuel pellets

Here, the steam oxidation resistance of UN and UN-(20 vol%)ZrN fuel pellets is evaluated to enhance understanding of steam corrosion mechanisms in advanced nuclear fuel materials. In situ neutron diffraction shows the modified UN fuel pellets form a (U 0.77 ,Zr 0.23 )N solid-solution and the sole crystalline oxidation product detected in bulk is (U 0.77 ,Zr 0.23 )O 2 . U 2 N 3 is not detected in significant quantities during the steam oxidation of UN or (U 0.77 ,Zr 0.23 )N and stable lattice parameters show that hydriding does not take place. Steam oxidation rates, obtained via sequential Rietveld refinement show how (U 0.77 ,Zr 0.23 )N has a higher activation energy (79 ± 1 kJmol -1 vs. 50 ± 5 kJmol -1 ), higher onset temperature (430 °C vs. 400 °C) and slower reaction rates for steam oxidation up to 616 °C, than pure UN. Throughout, both UN and (U 0.77 ,Zr 0.23 )N exhibit linear (non-protective) oxidation kinetics, signifying that degradation of the fuel pellets is caused by the evolution of gaseous products at the interface followed by oxide scale spallation. This quantitative and mechanistic understanding of material degradation enables better defined operating regimes and points towards (U,Zr)N solid solutions as a promising strategy for the design of advanced nuclear fuel materials with enhanced steam corrosion resistance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Evaluation of Irradiation Creep Effects in HT9 Cladding for FAST Experiments

The push for advanced reactor fuels for improved reactor safety and efficiency had led to a renewed interest in metallic fuel for nuclear reactor applications. Experimental investigation is necessary to ensure a robust understanding of the thermomechanical properties of new metallic fuel designs. Unfortunately, with the current experimental facilities, thoroughly investigating the responses of metallic fuel burnup would take a prohibitively long time. To alleviate this, the Fission Accelerated Steady State Test (FAST) was developed to accelerate the irradiation testing while simultaneously decreasing the sensitivity to fabrication tolerances by reducing the fuel diameter and scaling the experiment. This method successfully scales the radiation effects on the fuel, but the HT9 cladding is not exposed to prototypic radiation conditions. This raises questions on whether the FAST experiment results are truly indicative of the HT9 cladding performance due to radiation induced creep effects not being appropriately accounted for. Using BISON fuel performance code, the simulated FAST cladding strain is compared to simulated EBR-II cladding strain. This is done through a sensitivity study of input parameters and scaling of neutron fluence on the cladding. This allows a parametric comparison of physical phenomena on the effective difference between cladding strains between FAST and equivalent burnup EBR-II fuel pins. The results show that the irradiation induced deformation (creep or swelling) is insignificant compared to the thermal-mechanical deformation. Therefore, the difference between the FAST experiment cladding and the EBR-II experiment cladding is negligible and comparison of fuel system performance between the two experiments is appropriate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Separate-Effects Tests for Studying Temperature-Gradient-Driven Cracking in UO 2 Pellets

We report a variety of normal operation and accident scenarios can generate thermal stresses large enough to cause cracking in light-water reactor (LWR) fuel pellets. Cracking of fuel pellets can lead to reduced heat removal, higher centerline temperatures, and localized stress in cladding, all of which impact fuel performance. It is important to experimentally characterize the thermal and mechanical behavior in the pellet before and after cracking to improve cracking models in fuel performance codes. However, in-reactor observation and measurement of cracking is very challenging due to the harsh environment and logistics. Recently, an experimental pellet cracking test stand was developed for separate effects testing of normal operations and accident temperature conditions, using thermal imaging to capture the pellet surface temperature for evaluation of thermal stresses and optical imaging to capture the evolution of cracking in real time. Experiments were performed using depleted uranium dioxide (UO 2 ) pellets, which are useful for collecting data valuable for development and validation of cracking models. A combination of induction and resistance heating was used to create an average temperature gradient of 236°C/cm and 193°C/cm before and after cracking respectively. Characterization of the pellets were done before as well as after cracking. The cracking patterns are somewhat different than those expected in a typical reactor because of the differences in thermal conditions and pellet microstructure. However, if the actual conditions of these experiments are reproduced in computational models, these out-of-pile tests on UO 2 pellets provide relevant data for modeling purposes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Coupled physics simulation of fracture in nuclear fuel pellets induced by resistive heating

While it is well known that the UO 2 fuel used in light-water reactors cracks early in its life in the reactor, it is very difficult to collect in-reactor data regarding fuel cracking initiation and propagation to validate fracture models in fuel performance codes. Most fracture data comes from the post-irradiation examination of fuel that has been subjected to long and complex power histories. Replicating the thermal gradients experienced in this fuel to study crack initiation and propagation in a laboratory environment is challenging. This is primarily because the fuel is heated volumetrically by fission, which is difficult to replicate. One way to approximate this volumetric heating out of the reactor is to use electrical resistance (or Joule heating). An electrical conductivity model has been developed and coupled with the existing thermomechanical modeling capability in the BISON nuclear fuel performance code. This will permit simulation of experiments that use resistive heating for the purpose of validating fracture models in BISON. The modeling approach developed here is applied to simulate both historical and current resistive heating experiments on ceramic nuclear fuel.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗