Engineering Papers⌕ Search

Engineering topics

Pathak, Rajesh

Publications and source records attributed to Pathak, Rajesh.

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High‐Energy LiNiO 2 Li Metal Batteries Enabled by Hybrid Electrolyte Consisting of Ionic Liquid and Weakly Solvating Fluorinated Ether

Abstract In pursuit of the highest possible energy density, researchers shift their focus to the ultimate anode material, lithium metal (Li 0 ), and high‐capacity cathode materials with high nickel content (Ni > 80%). The combination of these aggressive electrodes presents unprecedented challenges to the electrolyte. Here, we report a hybrid electrolyte consisting of a highly fluorinated ionic liquid and a weakly solvating fluorinated ether, whose hybridization structure enables the reversible operation of a battery chemistry based on Li 0 and LiNiO 2 (Ni = 100%), delivering nearly theoretical capacity of the latter (up to 249 mAh g −1 ) for >300 cycles with retention of 78.6% and in absence of unwanted morphological changes in both electrodes. Extensive characterization assisted by molecular dynamic simulation and density functional theory calculations reveals the function of the fluorinated ether to be far more profound than simple dilution and viscosity reduction. Instead, it induces drastic changes in Li + ‐solvation environment, the consequence of which engenders simultaneous stabilization of electrode/electrolyte and interfacing via formation of respective interfacial chemistries. This study further unlocks fundamental knowledge underneath the prevailing “diluent strategy” that is extensively applied by the electrolyte researchers and opens more design space for the next‐generation electrolytes and interphases for these coveted battery chemistries.

25 ENERGY STORAGE↗
DOE OSTI2024

In Situ Exploration of Dipole Field Effects on Weak Hysteresis in 3D/2D Perovskites

This research delves into the effects of 2D layers on the functionality of 3D perovskite using lock-in amplifier-based in situ surface photovoltage (SPV) and its phase spectroscopy, with an emphasis on elucidating the connection between the tuning of dipole moments and the photocurrent hysteresis. Conventionally, the SPV of a perovskite/hole transport layer is observed to diminish as positive bias escalates. However, this trend is reversed in the case of 3D perovskite samples, where an augmentation in SPV is noted under positive bias. Notably, 3D/2D perovskite structures initially show a decrease, then an increase in SPV as bias intensifies, a phenomenon more pronounced with larger dipole moments in 2D. However, there is no linear relationship between the dipole moment and the hysteresis factor. Furthermore, using in situ light-chopping-frequency-modulated SPV and Kelvin Probe Force Microscopy, it is revealed that the dipole fields of 2D layers can hinder ion migration. This leads to efficient hole transfer and minimal photocurrent hysteresis in 3D/2D perovskites, providing strong evidence for the underlying cause of hysteresis. Additionally, these findings suggest intricate interplays among the external electric field, interface dipole moments, and surface photovoltaics, offering significant insights into perovskite optoelectronics.

3D/2D perovskite↗
DOE OSTI2024

Thiol-Functionalized Adsorbents through Atomic Layer Deposition and Vapor-Phase Silanization for Heavy Metal Ion Removal

The removal of toxic heavy metal ions from water resources is crucial for environmental protection and public health. In this study, we address this challenge by developing a surface functionalization technique for the selective adsorption of these contaminants. Our approach involves atomic layer deposition (ALD) followed by vapor-phase silanization of porous substrates. We utilized porous silica gel powder (similar to 100 mu m particles, 89 m 2 /g surface area, similar to 30 nm pores) as an initial substrate. This powder was first coated with similar to 0.5 nm ALD Al 2 O 3 , followed by vapor-phase grafting of a thiol-functional silane. The modified powder, particularly in acidic conditions (pH = 4), showed high selectivity in adsorbing Cd(II), As(V), Pb(II), Hg(II), and Cu(II) heavy metal ions in mixed ion solutions over common benign ions (e.g., Na, K, Ca, and Mg). Langmuir adsorption isotherms and breakthrough adsorption studies were conducted to assess heavy metal binding affinity and revealed the order of Cd(II) < Pb(II) < Cu(II) < As(V) < Hg(II), with a significantly higher affinity for As(V) and Hg(II) ions. Time-dependent uptake studies demonstrated rapid removal of heavy metal ions from aqueous environments, with Hg(II) exhibiting the fastest adsorption kinetics on thiol-modified surfaces. Finally, these findings highlight the potential of ALD and vapor-phase silanization to create effective adsorbents for the targeted removal of hazardous contaminants from water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Tailoring the Interfacial Interactions of Porous Polymer Membranes to Accelerate Atomic Layer Deposition: The Latent Path to Antifouling Membranes

Atomic layer deposition (ALD) is a powerful strategy to engineer hybrid organic-inorganic membranes with emergent functionalities. The combination of atomic-level thickness control, a wide materials palette, and unprecedented conformality allows the physiochemical properties (e.g., hydrophilicity) of mesoporous polymer membranes to be precisely tuned. The nucleation of ALD material growth on polymer surfaces relies on Lewis acid-base interactions and remains an overlooked motif with tremendous potential to accelerate ALD nucleation and growth. Strategies to enhance these interactions could enable desirable properties such as antifouling behavior to be imparted on inert polymer surfaces that lack the necessary functional groups for ALD nucleation. Here, in this study, we demonstrate that the reactivity of polyacrylonitrile (PAN) membranes toward ALD metal oxide (MO) precursors with Lewis acid characteristics is enhanced by introducing strong Lewis base functional groups (amidoxime: Am) on the PAN backbone (Am-PAN). The resulting Lewis acid-base interactions accelerate the MO nucleation in Am-PAN and reduce the number of deposition cycles required to achieve hydrophilicity compared with the untreated PAN membrane. Unveiling the reaction mechanism, in situ Fourier transform infrared (FTIR) spectroscopy measurements established enhanced interaction dynamics between the ALD MO precursors and the Am-PAN membrane, unlike the PAN membrane. Spectroscopic ellipsometry and thermogravimetric analysis measurements revealed higher MO loadings in Am-PAN membranes compared to PAN membranes for the same number of ALD cycles. We found that strong Lewis acid-base interactions accelerated the ALD for a range of materials including Al 2 O 3 , TiO 2 , SnO 2 , and ZnO. More broadly, our work demonstrates that tailoring metal-precursor-polymer interactions is a powerful strategy to accelerate and modulate the ALD. We used this design strategy to fabricate Al 2 O 3 -Am-PAN hybrid membranes that showed 2-fold higher antifouling capability compared to pristine PAN membranes prepared with an equivalent number of Al 2 O 3 ALD cycles. Our approach expands the scope of design options for fouling-resistant porous hybrid inorganic-organic membranes and may ultimately reduce the operational costs of water treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Controlling Nanoscale Pore Size and Wall Composition in Polycarbonate Membranes via Atomic Layer Deposition and Sequential Infiltration Synthesis: Implications for High Water Permeance

Polymer membranes have a wide variety of applications, ranging from water treatment to energy storage. Many of these applications require precise control over the membrane porosity and surface chemistry. In this study, we explore the modification of isoporous polycarbonate (PC) track-etched membranes (PCTEs) by atomic layer deposition (ALD) and sequential infiltration synthesis (SIS) to tune the pore size and the pore wall surface chemistry. We first performed a detailed study of Al 2 O 3 ALD and SIS in PCTE using a variety of in situ and ex situ measurements. We discovered that short precursor exposure times are critical to achieve conformal Al 2 O 3 ALD in the PCTE nanopores, while longer precursor exposure times resulted in Al 2 O 3 SIS within the bulk of the PC leaving the membranes brittle. Next, we tuned the PCTE pore size via Al 2 O 3 ALD and studied its effect on the water contact angle and the water permeance. Here, we found that the membranes became more hydrophilic, and the permeance decreased with increasing ALD Al 2 O 3 cycles. Finally, we studied the effect of hydrophilic (SnO 2 )/hydrophobic (In 2 O 3 ) ALD metal oxide coatings on membrane properties. We found that the most hydrophilic SnO 2 showed the highest water flux and the least hydrophilic In 2 O 3 showed the lowest water flux through the PCTE membranes. Our results demonstrate that ALD is an effective method to tune the surface and transport properties of PCTE membranes, but care must be exercised to avoid SIS and bulk modification of the polymer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Enhancing the performance of the perovskite solar cells by modifying the SnO 2 electron transport layer

The tin oxide (SnO 2 ) electron transport layer (ETL) plays a vital role in the photo-conversion efficiency (PCE) and stability of organic-inorganic perovskite solar cells (PSCs). However, SnO 2 ETL-induced defects such as hydroxyl groups, oxygen vacancies, exposed Sn atoms, and dangling bonds hinder device performance. In this study, rubidium chloride (RbCl) has been used to modify the SnO 2 ETL. Perovskite film formed on the RbCl-modified SnO 2 ETL exhibits improved crystallinity with enlarged grain size and reduced grain boundaries and enhanced optical absorption. Further, the Hall-effect measurements indicate the improved carrier mobility, and the dark J-V curve shows the increment of electrical conductivity for the RbCl-modified SnO 2 ETL. X-ray photoelectron spectroscopy (XPS) results demonstrate the surface defects passivation of the perovskite layer by modifying the SnO 2 ETL. A champion PCE of 19.35% has been achieved for the RbCl-modified SnO 2 ETL-based devices with improved stability, while the control devices with unmodified SnO 2 ETL show a PCE of 17.18%.

14 SOLAR ENERGY↗
DOE OSTI2023

Vapor-phase grafting of functional silanes on atomic layer deposited Al 2 O 3

Fundamental studies are needed to advance our understanding of selective adsorption in aqueous environments and develop more effective sorbents and filters for water treatment. Vapor-phase grafting of functional silanes is an effective method to prepare well-defined surfaces to study selective adsorption. In this investigation, we perform vapor phase grafting of five different silane compounds on aluminum oxide (Al2O3) surfaces prepared by atomic layer deposition. These silane compounds have the general formula L3Si–C3H6–X where the ligand, L, controls the reactivity with the hydroxylated Al2O3 surface and the functional moiety, X, dictates the surface properties of the grafted layer. We study the grafting process using in situ Fourier transform infrared spectroscopy and ex situ x-ray photoelectron spectroscopy measurements, and we characterize the surfaces using scanning electron microscopy, atomic force microscopy, and water contact angle measurements. Here, we found that the structure and density of grafted aminosilanes are influenced by their chemical reactivity and steric constraints around the silicon atom as well as by the nature of the anchoring functional groups. Methyl substituted aminosilanes yielded more hydrophobic surfaces with a higher surface density at higher grafting temperatures. Thiol and nitrile terminated silanes were also studied and compared to the aminosilane terminated surfaces. Uniform monolayer coatings were observed for ethoxy-based silanes, but chlorosilanes exhibited nonuniform coatings as verified by atomic force microscopy measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multifunctional transitional metal-based phosphide nanoparticles towards improved polysulfide confinement and redox kinetics for highly stable lithium-sulfur batteries

The shuttle effect and the sluggish redox kinetics of lithium polysulfides (LiPSs) are the major issues impeding the practical applications of lithium-sulfur batteries (LSBs). Herein, a highly-efficient Ni 2 P electrocatalyst supported on N, P co-doped graphene (Ni 2 P@NPG) is developed via a simple “recrystallization-self-assembly” method to address the above issues. Here, the ultrafine Ni 2 P nanoparticles ensure abundant adsorption-diffusion-conversion interfaces for accelerating LiPSs transformation and Li 2 S deposition, which extremely decreases the accumulation of LiPSs in the electrolyte and therefore prevents the migration of LiPSs. Their superior catalytic performance is demonstrated by reduced Gibbs free energy changes of rate-limiting step based on the systematic theoretical calculations and the reduced shuttle effect is tested by the three-dimensional reconstructions of Raman depth profiles. Benefiting from these synergistic effects, the LSBs with Ni 2 P@NPG modified separators present a superior cycling performance with an average capacity decay rate of 0.048 % per cycle at 1C around the 400 cycles and a high-rate capacity of 731 mAh/g at 2C. Even with a high-sulfur loading of 3.53 mg cm –2 , the cell can still contain a reversible capacity of 809 mAh/g at 0.2C with a remarkable columbic efficiency of 98.4 %.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Mitigating Interfacial Mismatch between Lithium Metal and Garnet-Type Solid Electrolyte by Depositing Metal Nitride Lithiophilic Interlayer

Solid-state lithium batteries are generally considered as the next-generation battery technology that benefits from inherent nonflammable solid electrolytes and safe harnessing of high-capacity lithium metal. Among various solid-electrolyte candidates, cubic garnet-type Li 7 La 3 Zr 2 O 12 ceramics hold superiority due to their high ionic conductivity (10 –3 to 10 –4 S cm -1 ) and good chemical stability against lithium metal. However, practical deployment of solid-state batteries based on such garnet-type materials has been constrained by poor interfacing between lithium and garnet that displays high impedance and uneven current distribution. Herein, we propose a facile and effective strategy to significantly reduce this interfacial mismatch by modifying the surface of such garnet-type solid electrolyte with a thin layer of silicon nitride (Si 3 N 4 ). This interfacial layer ensures an intimate contact with lithium due to its lithiophilic nature and formation of an intermediate lithium–metal alloy. The interfacial resistance experiences an exponential drop from 1197 to 84.5 Ω cm 2 . Lithium symmetrical cells with Si 3 N 4 -modified garnet exhibited low overpotential and long-term stable plating/stripping cycles at room temperature compared to bare garnet. Furthermore, a hybrid solid-state battery with Si 3 N 4 -modified garnet sandwiched between lithium metal anode and LiFePO 4 cathode was demonstrated to operate with high cycling efficiency, excellent rate capability, and good electrochemical stability. This work represents a significant advancement toward use of garnet solid electrolytes in lithium metal batteries for the next-generation energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2021

Advanced strategies for the development of porous carbon as a Li host/current collector for lithium metal batteries

Lithium metal is considered a promising anode material for high-energy-density rechargeable batteries because of its high specific theoretical capacity (3860 mAh g -1 , low mass density (0.534 g cm -3 ), and low electrochemical redox potential (-3.04 V vs. the standard hydrogen electrode). However, the high reactivity of Li with the electrolyte leads to the formation of an unstable solid electrolyte interphase (SEI) and continuous side reactions. Also, the non-uniform lithium-ion flux and infinite volume expansion of Li metal cause the growth of Li dendrites. These pose significant safety challenges and cause rapid capacity fading of the lithium metal batteries (LiMBs). To resolve these issues, a low-cost, easily processed, lightweight, high-performance carbon-based porous matrix is considered promising to host Li metal deposition. The three-dimensional (3D) porous nano/microstructured carbon provides sufficient space for Li accommodation during Li plating, buffers the volume changes during Li plating/stripping, and lowers the effective current density contributing to dendrite-free Li deposition. Besides, the outstanding electrochemical and mechanical stability, flexibility and the high electronic conductivity enable the nano/microstructured carbon to serve as both Li host and current collector. The development of 3D carbon/Li composite by mechanical roll-press techniques not only eliminates the complex and risky procedure of making carbon/Li composite based on Li plating or molten Li infusion but also stabilizes the capacity at higher Li plating/stripping rates. Recently, there is an advancement in the lithiophilic decorations of 3D structure to introduce sufficient nucleation sites and the development of artificial SEI on top of the 3D matrix to suppress Li dendrite formation. Such 3D structural modifications create a uniform electric field, lower the Li nucleation overpotential, provide strong mechanical and chemical stability, and stabilize the interface thereby inhibiting the degradation of lithium and the electrolyte. Here we summarize the research progress on porous carbon/Li composites in terms of materials type, structure, fabrication technique, their electrochemical battery performance, and identify the critical challenges that need to be addressed for high-energy-density practical LiMBs.

25 ENERGY STORAGE↗
DOE OSTI2021

Density Functional Theory Investigation of the NiO@Graphene Composite as a Urea Oxidation Catalyst in the Alkaline Electrolyte

Developing efficient and low-cost urea oxidation reaction (UOR) catalysts is a promising but still challenging task for environment and energy conversion technologies such as wastewater remediation and urea electrolysis. In this work, NiO nanoparticles that incorporated graphene as the NiO@Graphene composite were constructed to study the UOR process in terms of density functional theory. The single-atom model, which differed from the previous heterojunction model, was employed for the adsorption/desorption of urea and CO 2 in the alkaline media. As demonstrated from the calculated results, NiO@Graphene prefers to adsorb the hydroxyl group than urea in the initial stage due to the stronger adsorption energy of the hydroxyl group. After NiOOH@Graphene was formed in the alkaline electrolyte, it presents excellent desorption energy of CO 2 in the rate-determining step. Electronic density difference and the d band center diagram further confirmed that the Ni(III) species is the most favorable site for urea oxidation while facilitating charge transfer between urea and NiO@Graphene. Moreover, graphene provides a large surface for the incorporation of NiO nanoparticles, enhancing the electron transfer between NiOOH and graphene and promoting the mass transport in the alkaline electrolyte. Notably, this work provides theoretical guidance for the electrochemical urea oxidation work.

25 ENERGY STORAGE↗