Engineering topics
Publications and source records attributed to Parker, J..
Global Positioning System (GPS) data are useful for understanding both interseismic and postseismic deformation. Models of GPS data suggest that the lower crust, lateral heterogeneity, and fault slip, all provide a role in the earthquake cycle.
The M7.1 Hector Mine earthquake ruptured the Lavic Lake fault near Twentynine Palms, CA at 09:46 UTC October 16, 1999.
Small amounts of second phase materials can have important effects on the thermoelectric properties of polycrystalline gamma-La(3-x)X4 (X-S, Te; X in the range of 0 to 1/3). Microscopic examination by SEM of hot pressed La(3-x)Te4 samples has revealed from 1-5 vol. pct of La2O2Te, an amount which is not detected by X-ray powder diffraction measurements. This amount of La2O2Te resulting from oxygen contamination can reduce the concentration of electrons by as much as 10 to 75 percent below the electron concentration calculated for single phase La(3-x)Te4 in the composition range of greatest interest. Small amounts of second phase materials can also lower the lattice thermal conductivity by scattering low frequency phonons. These results indicate that microstructural effects should be considered when electrical and thermal properties of polycrystalline materials are analyzed.
Solar flares produce increases in coherent-scatter power from the mesosphere due to the increase in free electrons produced by X-ray photoionization. Thirteen such power enhancements were observed at Urbana. When such an enhancement occurs at an altitude containing a turbulence layer with constant strength, the relative enhancement of electon density is estimated from the enhancement in power. Such estimates of enchanced electron density are compared with estimates of the X-ray photoionization at that altitude, deduced from geostationary satellite measurements. It is found that possible types ion-chemical reaction scheme may be distinguished, and the nonflare ion-pair production function may be estimated. The type of ion-chemical scheme and the nonflare ion-production function are shown to depend on the solar zenith angle.
The processing techniques and problems encountered in formulating metallo-organic decomposition (MOD) films used in contracting structures for thin solar cells are described. The use of thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) techniques performed at Jet Propulsion Laboratory (JPL) in understanding the decomposition reactions lead to improvements in process procedures. The characteristics of the available MOD films were described in detail.
The Seebeck coefficient, electrical resistivity, thermal conductivity, and Hall effect have been studied in gamma-phase La(3-x)S4(LaS/y/) for compositions with x in the range from 0.04 to 0.3 (y in the range from 1.35 to 1.48) in order to ascertain its suitability for high-temperature (300 to 1400 K) thermoelectric energy conversion. In this temperature and composition range the material behaves as an extrinsic semiconductor whose degenerate carrier concentration is controlled by the stoichiometric ratio of La to S. A maximum figure-of-merit (Z) of approximately 0.0005 per K at a composition x = 0.3, y = 1.48 (LaS/1.48/) was obtained.
Group of phthalocyanine polymers resist thermal degradation. Polymers expected semiconducting. Principal applications probably in molded or laminated parts that have to withstand high temperatures. Polymers made from either of two classes of monomer: Bisphthalonitriles with imide linkages or Bisphthalonitriles with ester-imide linkages.
Efficient synthesis of analytically-pure metal (II) 4,4',4'',4''' tetraaminophthalocyanine demonstrated in experiments. Typical Polymerization proceeds in two steps: First, reaction with 3,3',4,4'' -benzophenonetetracarboxylic dianhydride. Second step cyclodehydration. New polymers expected useful in formulation of thermally stable varnishes, adhesives, and fibers.
Graphite/epoxy composite materials made with resins containing bromine and rubber additives. New composites tougher and more resistant to fire. Flame resistance increased by introducing bromine via commercial brominated flame-retartant polymeric additives.
New resins yield laminates with improved mechanical properties. Ingredients of Modified Polymer include bisimide of formula 1 and amine-terminated elastomer. Cure effected by heating to temperature suited to particular ingredients used, generally in range of 200 degrees to 300 degrees C. Solution of solvent and reactants used for fabricating fiber-reinforced structures or as adhesive.
A high-temperature Hall-effect apparatus is described which allows measurements up to temperatures greater than 1200 K using the van der Pauw method. The apparatus was designed for measurements on refractory materials having high charge carrier concentrations and generally low mobilities. Pressure contacts are applied to the samples. Consequently, special contacting methods, peculiar to a specific sample material, are not required. The apparatus has been semiautomated to facilitate measurements. Results are presented on n- and p-type silicon.
Improved thick film solar cell contacts for the high volume production of low cost silicon solar arrays are needed. All metal screenable pastes made from economical base metals and suitable for application to low to high conductivity silicon were examined. Silver fluoride containing copper pastes and fluorocarbon containing copper pastes were discussed. The effect of hydrogen on the adhesion of metals to silicon was investigated. A cost analysis of various paste materials is provided.
Electrodes made with pastes produced under the previous contract were analyzed and compared with raw materials. A needle-like structure observed on the electroded solar cell was identified as eutectic copper-silicon, a phase considered to benefit the electrical and metallurgical properties of the contact. Electrodes made from copper fluorocarbon and copper silver fluoride also contained this phase but had poor adhesion. A liquid medium, intended to provide transport during carbon fluoride decomposition was incorporated into the paste resulting in better adhesion. The product survived preliminary environmental tests. A 2 cm by 2 cm solar cell made with fluorocarbon activated copper electrodes and gave 7% AMI efficiency (without AR coating). Both silver fluoride and fluorocarbon screened paste electrodes can be produced for approximately $0.04 per watt.
A drag compensation system for solar probes and other spacecraft that require a drag-free capability is presented. Estimation techniques, derived from modern control theory, are proposed.