Engineering Papers⌕ Search

Engineering topics

Park, C.

Publications and source records attributed to Park, C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effect of low-temperature compression on superconductivity and crystal structure in strontium metal

The superconducting and structural properties of elemental strontium metal were investigated under pressures up to 60 GPa while maintaining cryogenic conditions during pressure application. Applying pressure at low temperatures reveals differences in superconducting and structural phases compared to previous reports obtained at room temperatures. Notably, the superconducting critical temperature exhibits a twofold increase under compression after cryogenic cooling within the pressure range of 35–42 GPa, compared to cryogenic cooling after room-temperature compression. Subsequently, the transition width becomes significantly sharper above 42 GPa. Low-temperature x-ray diffraction measurements under pressure reveal that this change corresponds to the Sr-III to Sr-IV transition, with no evidence of any metastable structure. Furthermore, the monoclinic Sr-IV structure was observed to remain stable to much higher pressures—at least up to 60 GPa, without the appearance of the incommensurate Sr-V phase present at room temperature. As a result, this implies that thermal activation energy plays an important role in overcoming the presence of a kinetic barrier to the Sr-V phase at room temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2020

Mg Isotopic Compositions of Fine-Grained Ca-Al-Rich Inclusions from Reduced CV3 Chondrites and Implications on the Timescale of Nebular Condensation

Fine-grained Ca-Al-rich inclusions (FGIs) in carbonaceous chondrites are interpreted as aggregates of nebular gas-solid condensates that escaped significant melting [1]. Recent Al-Mg isotopic studies of small FGIs (<200 µm in size) from pristine CO3 chondrites have revealed significant variations in initial 26Al/27Al ratio, (26Al/27Al)(sub 0), spanning from 5.73×10(exp ˗5) to 8×10(exp ˗6) [2,3]. Importantly, [3] found a main CAI population characterized by (26Al/27Al)(sub 0) = 5.4×10(exp ˗5) that likely record the onset of dust condensation and initial coagulation events, followed by multiple thermal events over an extended time period. Thus far, a small number of large FGIs from CV3 chondrites have been analyzed, showing a narrower range of ( 26Al/27Al)(sub 0) = 5.27×10(exp ˗5) to 3.35×10(exp ˗5) [4-6], similar to those inferred from coarse-grained, igneous CAIs (CGIs) from CV3 chondrites [7]. These observed different ratios may raise a question if large FGIs in CV3 chondrites record a time interval from primary direct condensation of refractory solids to their aggregation and growth into larger inclusions. In this study, we present Al-Mg isotopic compositions of FGIs from reduced CV3 chondrites to better constrain their formation timescale relative to smaller FGIs in CO3 chondrites, as well as to CGIs in CV3 chondrites. This isotopic study is coordinated with a microstructural study to elucidate the origin and nature of FGIs in the petrologic and mineralogical context.

Han, J.↗
NASA NTRS2020

Mineralogy and Petrology of Fine-Grained Calcium-Aluminum-Rich Inclusions from the Reduced CV3 Chondrite Thiel Mountains 07007

Calcium-Aluminum-rich inclusions (CAIs) are among the oldest Solar System solids, and studies of these objects have played an essential role in developing an understanding of chemical and physical processes that initiated and characterized key events related to the Solar System’s formation and evolution. CAIs occur as μm- to cm-sized inclusions in chondritic meteorites, particularly in carbonaceous chondrites, and consist of various refractory silicate and oxide phases (e.g., melilite, spinel, Al-Ti-rich diopside, hibonite, and corundum) that are predicted by thermodynamic models to be among the first solids to con-dense from a cooling gas of solar composition. Fine grained CAIs (FGIs) are important samples to probe volatility-driven condensation processes in the solar nebula, because they have escaped thermal processes (e.g., melting) experienced by coarse-grained CAIs. In order to explore the primary nebular history of FGIs, a detailed mineralogical and petrologic study is necessary. In this research effort, we constrained the mineralogy and petrology of two CAIs 07-10 and -11 from the reduced CV3 chondrite Thiel Mountains (TIL) 07007, with the aim of evaluating their provenance as nebular condensates.

Anderkin, C. J.↗
NASA NTRS2019

Microstructural Record of Evolving Condensation Processes in Fine-Grained Ca-Al-Rich Inclusions from the Reduced CV3 Chondrites

Fine-grained, spinel-rich Ca-Al-rich inclusions (FGIs) in carbonaceous chondrites consist of numerous layered nodules having cores of spinel, hibonite, and/or perovskite surrounded by multiple thin layers of melilite, anorthite, diopside, and/or olivine. They are interpreted as aggregates of direct high-temperature condensates from an 16O-rich nebular gas that escaped significant melting. However, FGIs are very complex objects composed of intimate intergrowths of fine-grained refractory phases and show extremely large variations in mineralogy, modal abundance, and textures. Thus, detailed FIB/TEM analyses of FGIs are required to fully characterize their micro-to-nanometer scale textures, mineralogy, and chemical compositions and hence elucidate their formation processes and conditions in the early solar nebula. Here, we present our on-going study of pristine FGIs from the reduced CV3 chondrites Efremovka and Thiel Mountains (TIL) 07003 and 07007 that have minimal evidence for secondary parent body alteration.

Han, J.↗
NASA NTRS2017

Interfacial and Hydrodynamic Behavior of Thin Spherical Bubbles of Smectic Liquid Crystal in Microgravity

The Observation and Analysis of Smectic Islands in Space (OASIS) project comprises a series of experiments that probe the interfacial and hydrodynamic behavior of thin spherical bubbles of smectic liquid crystal in microgravity. Smectic films are the thinnest known structures formed of condensed phases, making them ideal for studies of two-dimensional (2D) coarsening dynamics and thermocapillary phenomena. The OASIS flight hardware was launched on SpaceX-6 in April 2015 and experiments were carried out on the International Space Station using four different smectic A and C liquid crystal materials in separate sample chambers. We will describe the behavior of collective island dynamics on the bubbles, including temperature-gradient-induced thermomigration, 2D Rayleigh-Plateau Instability, Oswald ripening dynamics, the single and multiple island diffusion on the curved surface and coalescence-driven coarsening dynamics of island emulsions in microgravity. On Earth, such island emulsions would rapidly sediment to the bottom of the bubble and coalesce, but in microgravity, coarsening of the emulsion can be observed free of gravitational effects.

liquid crystal↗
NASA NTRS2016

Thermodynamic Approach to Boron Nitride Nanotube Solubility and Dispersion

Inadequate dispersion of nanomaterials is a critical issue that significantly limits the potential properties of nanocomposites and when overcome, will enable further enhancement of material properties. The most common methods used to improve dispersion include surface functionalization, surfactants, polymer wrapping, and sonication. Although these approaches have proven effective, they often achieve dispersion by altering the surface or structure of the nanomaterial and ultimately, their intrinsic properties. Co-solvents are commonly utilized in the polymer, paint, and art conservation industries to selectively dissolve materials. These co-solvents are utilized based on thermodynamic interaction parameters and are chosen so that the original materials are not affected. The same concept was applied to enhance the dispersion of boron nitride nanotubes (BNNTs) to facilitate the fabrication of BNNT nanocomposites. Of the solvents tested, dimethylacetamide (DMAc) exhibited the most stable, uniform dispersion of BNNTs, followed by N,N-dimethylformamide (DMF), acetone, and N-methyl-2-pyrrolidone (NMP). Utilizing the known Hansen solubility parameters of these solvents in comparison to the BNNT dispersion state, a region of good solubility was proposed. This solubility region was used to identify co-solvent systems that led to improved BNNT dispersion in poor solvents such as toluene, hexane, and ethanol. Incorporating the data from the co-solvent studies further refined the proposed solubility region. From this region, the Hansen solubility parameters for BNNTs are thought to lie at the midpoint of the solubility sphere: 16.8, 10.7, and 9.0 MPa(exp 1/2) for delta d, delta p, and delta h, respectively, with a calculated Hildebrand parameter of 21.8 MPa)exp 1/2).

Tiano, A. L.↗
NASA NTRS2012

Nanostructured Solar Irradiation Control Materials for Solar Energy Conversion

Tailoring the solar absorptivity (alpha(sub s)) and thermal emissivity (epsilon(sub T)) of materials constitutes an innovative approach to solar energy control and energy conversion. Numerous ceramic and metallic materials are currently available for solar absorbance/thermal emittance control. However, conventional metal oxides and dielectric/metal/dielectric multi-coatings have limited utility due to residual shear stresses resulting from the different coefficient of thermal expansion of the layered materials. This research presents an alternate approach based on nanoparticle-filled polymers to afford mechanically durable solar-absorptive and thermally-emissive polymer nanocomposites. The alpha(sub s) and epsilon(sub T) were measured with various nano inclusions, such as carbon nanophase particles (CNPs), at different concentrations. Research has shown that adding only 5 wt% CNPs increased the alpha(sub s) and epsilon(sub T) by a factor of about 47 and 2, respectively, compared to the pristine polymer. The effect of solar irradiation control of the nanocomposite on solar energy conversion was studied. The solar irradiation control coatings increased the power generation of solar thermoelectric cells by more than 380% compared to that of a control power cell without solar irradiation control coatings.

Kang, Jinho↗
NASA NTRS2004

Novel Phenylethynyl Imide Silanes as Coupling Agents for Titanium Alloy

The durability of titanium (Ti) alloys bonded with high temperature adhesives such as polyimides has failed to attain the level of performance required for many applications. The problem to a large part is attributed to the instability of the surface treatment on the Ti substrate. Although Ti alloy adhesive specimens with surface treatments such as chromic acid anodization, Pasa-Jell, Turco, etc. have provided high initial mechanical properties, these properties have decreased as a function of aging at ambient temperature and faster, when aged at elevated temperatures or in a hot-wet environment. As part of the High Speed Civil Transport program where Ti honeycomb sandwich structure must perform for 60,000 hours at 177 C, work was directed to the development of environmentally safe, durable Ti alloy surface treatments.

Park, C.↗
NASA NTRS2004

A Novel Surface Treatment for Titanium Alloys

High-speed commercial aircraft require a surface treatment for titanium (Ti) alloy that is both environmentally safe and durable under the conditions of supersonic flight. A number of pretreatment procedures for Ti alloy requiring multi-stages have been developed to produce a stable surface. Among the stages are, degreasing, mechanical abrasion, chemical etching, and electrochemical anodizing. These treatments exhibit significant variations in their long-term stability, and the benefits of each step in these processes still remain unclear. In addition, chromium compounds are often used in many chemical treatments and these materials are detrimental to the environment. Recently, a chromium-free surface treatment for Ti alloy has been reported, though not designed for high temperature applications. In the present study, a simple surface treatment process developed at NASA/LaRC is reported, offering a high performance surface for a variety of applications. This novel surface treatment for Ti alloy is conventionally achieved by forming oxides on the surface with a two-step chemical process without mechanical abrasion. This acid-followed-by-base treatment was designed to be cost effective and relatively safe to use in a commercial application. In addition, it is chromium-free, and has been successfully used with a sol-gel coating to afford a strong adhesive bond after exposure to hot-wet environments. Phenylethynyl containing adhesives were used to evaluate this surface treatment with sol-gel solutions made of novel imide silanes developed at NASA/LaRC. Oxide layers developed by this process were controlled by immersion time and temperature and solution concentration. The morphology and chemical composition of the oxide layers were investigated using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Auger electron spectroscopy (AES). Bond strengths made with this new treatment were evaluated using single lap shear tests.

Lowther, S. E.↗
NASA NTRS2002

Polymer-Single Wall Carbon Nanotube Composites for Potential Spacecraft Applications

Polymer-single wall carbon nanotube (SWNT) composite films were prepared and characterized as part of an effort to develop polymeric materials with improved combinations of properties for potential use on future spacecraft. Next generation spacecraft will require ultra-lightweight materials that possess specific and unique combinations of properties such as radiation and atomic oxygen resistance, low solar absorptivity, high thermal emissitivity, electrical conductivity, tear resistance, ability to be folded and seamed, and good mechanical properties. The objective of this work is to incorporate sufficient electrical conductivity into space durable polyimides to mitigate static charge build-up. The challenge is to obtain this level of conductivity (10(exp -8) S/cm) without degrading other properties of importance, particularly optical transparency. Several different approaches were attempted to fully disperse the SWNTs into the polymer matrix. These included high shear mixing, sonication, and synthesizing the polymers in the presence of pre-dispersed SWNTs. Acceptable levels of conductivity were obtained at loading levels less than one tenth weight percent SWNT without significantly sacrificing optical properties. Characterization of the nanocomposite films and the effect of SWNT concentration and dispersion on the conductivity, solar absorptivity, thermal emissivity, mechanical and thermal properties were discussed. Fibers and non-woven porous mats of SWNT reinforced polymer nanocomposite were produced using electrospinning.

Park, C.↗
NASA NTRS2002

Constitutive Modeling of Nanotube-Reinforced Polymer Composites

In this study, a technique is presented for developing constitutive models for polymer composite systems reinforced with single-walled carbon nanotubes (SWNT). Because the polymer molecules are on the same size scale as the nanotubes, the interaction at the polymer/nanotube interface is highly dependent on the local molecular structure and bonding. At these small length scales, the lattice structures of the nanotube and polymer chains cannot be considered continuous, and the bulk mechanical properties can no longer be determined through traditional micromechanical approaches that are formulated by using continuum mechanics. It is proposed herein that the nanotube, the local polymer near the nanotube, and the nanotube/polymer interface can be modeled as an effective continuum fiber using an equivalent-continuum modeling method. The effective fiber serves as a means for incorporating micromechanical analyses for the prediction of bulk mechanical properties of SWNT/polymer composites with various nanotube lengths, concentrations, and orientations. As an example, the proposed approach is used for the constitutive modeling of two SWNT/polyimide composite systems.

Odegard, G. M.↗
NASA NTRS2001

Organic-Inorganic Hybrids Using Novel Phenylethynyl Imide Silanes

In this presentation, polyimide-silica hybrids using novel phenylethynyl imide silanes are reported. The phenylethynyl group is present in the organic precursor as either a pendent or an end group to bond chemically with the polyimide adhesive containing phenylethynyl groups during processing, while the silane group of the organic precursor would chemically react with the inorganic precursor through oxane bond formation. The chemical compositions of these novel hybrids were examined using X-ray mapping modes of scanning electron microscopy (SEM), which revealed a silicon gradient interphase between the high surface energy substrate and the polyimide adhesive. Novel aromatic phenylethynyl imide silanes (APEISs) and pendent phenylethynyl imide oligomeric disilanes (PPEIDSs) have been synthesized, and sol-gel solutions containing the new silanes, a phenylethynyl terminated imide oligomer (PETI-5), and an inorganic precursor were formulated to develop a gradient hybrid interphase between a titanium alloy and the adhesive. Two different sol-gel systems were investigated to develop organic-inorganic hybrids. Hybrid I was composed of an organic precursor containing both phenylethynyl and silane groups (PPEIDS) and an inorganic precursor. Functional group concentrations were controlled by the variation of the molecular weight of the imide backbone of PPEIDS. Hybrid II was composed of organic and inorganic precursors and a coupling agent containing both phenylethynyl and silane groups. Morphology and chemical composition of the hybrid interphase between the inorganic substrate and the adhesive were investigated, and the bond strength and durability were evaluated using lap shear tests at various conditions. The assessment of how the bonding at an interface is affected by various sol-gel solution compositions and environments is reported.

Park, C.↗
NASA NTRS2000

Polyimide-Silica Hybrids Containing Novel Phenylethynyl Imide Silanes as Coupling Agents for Surface-Treated Titanium Alloy

Polyimide-silica hybrids composed of an organic precursor containing a novel phenylethynyl imide silane and an inorganic precursor were evaluated as an adhesion-promoting interphase between surface-treated titanium alloy and a phenylethynyl-containing imide adhesive. The phenylethynyl groups present in the organic precursor, either as a pendent or end group, can bond chemically with a phenylethynyl-containing imide adhesive during processing, while the silane groups of the organic precursor would react chemically with the inorganic precursor. In addition, the inorganic precursor is able to react with the titanium alloy to form a stable bond with the metal oxide. Bond strength and durability were evaluated by single lap shear tests at various conditions. Lap shear specimens exhibited predominantly cohesive failure after a 3-d water boil with 92% retention of the initial room temperature strength. Morphology and chemical composition of the hybrid interphase were investigated with scanning electron microscopy, X-ray photoelectron spectroscopy, and Auger electron spectroscopy, which revealed development of a silicon-gradient, hybrid structure between the metal substrate and the adhesive.

Park, C.↗
NASA NTRS2000

Polarization Stability of Amorphous Piezoelectric Polyimides

Amorphous polyimides containing polar functional groups have been synthesized and investigated for potential use as high temperature piezoelectric sensors. The thermal stability of the piezoelectric effect of one polyimide was evaluated as a function of various curing and poling conditions under dynamic and static thermal stimuli. First, the polymer samples were thermally cycled under strain by systematically increasing the maximum temperature from 50 C to 200 C while the piezoelectric strain coefficient was being measured. Second, the samples were isothermally aged at an elevated temperature in air, and the isothermal decay of the remanent polarization was measured at room temperature as a function of time. Both conventional and corona poling methods were evaluated. This material exhibited good thermal stability of the piezoelectric properties up to 100 C.

Park, C.↗
NASA NTRS1994

Towards Understanding the Fluid Dynamic Phenomenon of Interest to Rocket Base Heating: A Review

The significance of the base heating problem for rockets during ascent is due to the complex interaction between the rocket nozzle plumes and the external-flow which can change the flow characteristics in the base region dramatically. At lower altitudes the external-flow merges with the plume-flow, without the formation of a large separated flow region, and the cooler external-flow promotes convective cooling of the base wall. Under these conditions the majority of the base heating is due to radiative heating from the shock heated plume gases. At higher altitudes, however, the process of base heating is not so straightforward. The plume and the base flow expands dramatically and separated flow regions occur in the base area. Hot exhaust gases from the rocket nozzle will be entrained into the separated flow regions and produce a convective component to the base wall heating. Further, if the rocket exhaust-gas contains soot, the soot can increase the emission from the gas and dramatically increase the wall absorption coefficient for radiative heating if it is deposited on the walls . In addition, if the rocket exhaust gas is fuel rich, the fuel can bum in the separated flow regions and further increase the base heating. The base burning phenomenon, and the increased base heating caused by it at higher altitudes, have been observed for the Space Shuttle and Saturn Rocket. Under these conditions, the total heating is significantly higher than the heating without separated flow in the base region, and the increase in heating is directly attributable to the fluid dynamic complexity of the base region. Realistic simulation of the base heating requires that the calculated flow environment reproduce the fluid dynamic flow features accurately. Thus, it will be necessary to introduce into the CFD codes the capability for the flow to respond to the complex vehicle geometry, the effect of turbulence, the ability to accurately reproduce the plume shock/shear layer structures and capture such phenomenon as shock induced base separation and base-burning phenomenon. A survey of experimental, theoretical and computational work that details the fluid dynamics of the base flow environment will be presented in the proposed paper. CFD simulations of rocket base flows using standard CFD codes such as OVERFLOW or GASP will be explored to capture these phenomenon accurately. Merits and limitations of these codes for base flow environment predictions will be explored.

Venkatapathy, E.↗