Engineering topics

Pandya, A.

Publications and source records attributed to Pandya, A..

8 records

NASA NTRS1999

Evaluations of Three Methods for Remote Training

Long duration space missions require a change in training methods and technologies. For Shuttle missions, crew members could train for all the planned procedures, and carry documentation of planned procedures for a variety of contingencies. As International Space Station (ISS) missions of three months or longer are carried out, many more tasks will need to be performed for which little or no training was received prior to launch. Eventually, exploration missions will last several years, and communications with Earth will have long time delays or be impossible at times. This series of three studies was performed to identify the advantages and disadvantages of three types of training for self-instruction: video-conferencing; multimedia; and virtual reality. These studies each compared two types of training methods, on two different types of tasks. In two of the studies, the subject's were in an isolated, confined environment analogous to space flight; the third study was performed in a laboratory.

Woolford, B.↗

NASA NTRS1999

Effect of optical digitizer selection on the application accuracy of a surgical localization system-a quantitative comparison between the OPTOTRAK and flashpoint tracking systems

Application accuracy is a crucial factor for stereotactic surgical localization systems, in which space digitization camera systems are one of the most critical components. In this study we compared the effect of the OPTOTRAK 3020 space digitization system and the FlashPoint Model 3000 and 5000 3D digitizer systems on the application accuracy for interactive localization of intracranial lesions. A phantom was mounted with several implantable frameless markers which were randomly distributed on its surface. The target point was digitized and the coordinates were recorded and compared with reference points. The differences from the reference points represented the deviation from the "true point." The root mean square (RMS) was calculated to show the differences, and a paired t-test was used to analyze the results. The results with the phantom showed that, for 1-mm sections of CT scans, the RMS was 0.76 +/- 0. 54 mm for the OPTOTRAK system, 1.23 +/- 0.53 mm for the FlashPoint Model 3000 3D digitizer system, and 1.00 +/- 0.42 mm for the FlashPoint Model 5000 system. These preliminary results showed that there is no significant difference between the three tracking systems, and, from the quality point of view, they can all be used for image-guided surgery procedures. Copyright 1999 Wiley-Liss, Inc.

Non-NASA Center↗

NASA NTRS1992

Development of an empirically based dynamic biomechanical strength model

The focus here is on the development of a dynamic strength model for humans. Our model is based on empirical data. The shoulder, elbow, and wrist joints are characterized in terms of maximum isolated torque, position, and velocity in all rotational planes. This information is reduced by a least squares regression technique into a table of single variable second degree polynomial equations determining the torque as a function of position and velocity. The isolated joint torque equations are then used to compute forces resulting from a composite motion, which in this case is a ratchet wrench push and pull operation. What is presented here is a comparison of the computed or predicted results of the model with the actual measured values for the composite motion.

Pandya, A.↗

NASA NTRS1983

Investigation of the tip clearance flow inside and at the exit of a compressor rotor passage. II - Turbulence properties

The flow in the tip clearance region of a compressor rotor is highly turbulent due to the strong interaction of the leakage flow with the annulus wall boundary layer. This paper deals with the turbulence properties of the flow in the tip clearance region of a moderately loaded compressor rotor. The experimental results reported in this paper were obtained using a two-sensor hot-wire probe in combination with an ensemble averaging technique. Blade-to-blade distribution of the axial and tangential turbulence intensities at various radial locations and ten axial locations (four inside the blade passage and the remaining six outside the passage) were derived from this data. Isointensity contours in the clearance region at various radial locations were also obtained from the experimental data. A region of very high turbulence intensities was indicated at the half-chord location from these results. The turbulence intensity profiles also indicated that the leakage flow travels toward the midpassage before rolling up. The turbulence is almost isotropic beyond three-quarter chord downstream of the trailing edge.

Pandya, A.↗

NASA NTRS1983

Tip clearance flow in a compressor rotor passage at design and off-design conditions

The flow field in the tip clearance region of a compressor rotor at an off-design condition is reported in this paper. The earlier data at the design condition has also been re-interpreted and correlated with the blade and the flow parameters. The measurements inside the rotor tip region are acquired using a miniature hot wire sensor of 'V' configuration. The instantaneous velocity data is analyzed by the ensemble averaging technique to derive the blade-to-blade velocity field at various axial and radial locations between the rotor tip and the casing. The flow and the blade pressure data at the design condition are compared with the data at the off-design condition (lower blade loading). In addition to a reduction in the leakage velocities, its chordwise variation is also altered substantially at the lower blade loading.

Lakshminarayana, B.↗

NASA NTRS1982

Investigation of the tip clearance flow inside and at the exit of a compressor rotor passage

The nature of the tip clearance flow in a moderately loaded compressor rotor is studied. The measurements were taken inside the clearance between the annulus-wall casing and the rotor blade tip. These measurements were obtained using a stationary two-sensor hot-wire probe in combination with an ensemble averaging technique. The flowfield was surveyed at various radial locations and at ten axial locations, four of which were inside the blade passage in the clearance region and the remaining six outside the passage. Variations of the mean flow properties in the tangential and the radial directions at various axial locations were derived from the data. Variation of the leakage velocity at different axial stations and the annulus-wall boundary layer profiles from passage-averaged mean velocities were also estimated.

Pandya, A.↗

NASA NTRS1982

Investigation of the tip-clearance flow inside and at the exit of a compressor rotor passage. I - Mean velocity field

A stationary two-sensor hot-wire probe has been used in combination with an ensemble averaging technique to measure the flow in the tip clearance region of a compressor rotor with emphasis on the leakage flow development inside the tip-clearance region and at the exit of the rotor. It is found that the presence and interaction of leakage flow, annulus boundary layer, and the scraping vortex is the dominant feature at mid-chord position. The rotation of the blade augments the leakage flow, resulting in the movement of the leakage jet toward the mid-passage. The blade-to-blade distribution of properties is shown to be highly nonuniform, except in the downstream and upstream regions.

Pandya, A.↗

NASA NTRS1981

End wall flows in rotors and stators of a single stage compressor

A solution of the flow in the rotor end wall region, including the effects of tip clearance flow, is presented. A method for leakage flow measurement at the tip of a compressor rotor blade is discussed. Measurements are given for a rotor hub wall boundary layer.

Govindam, T. R.↗