Engineering Papers⌕ Search

Engineering topics

Pan, Chaochao

Publications and source records attributed to Pan, Chaochao.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Hot-Roll Fabrication of Anisotropic Nanograin Nd-Fe-B Magnet

Nd-Fe-B based magnets have the highest energy product among all permanent magnets, which is required for numerous clean energy technologies. For higher temperature applications (T > 150°C), additions of heavy rare earth elements (HREEs) such as Dy are required to maintain sufficient coercivity during operation. Additions of Dy are expensive. Thus, it is desirable to reduce the need for HREEs by reducing the grain size to the nanoscale, which increases the coercivity and decreases its temperature dependence. Here, we report a novel nanograin Nd-Fe-B magnet fabrication method that is continuous and inexpensive. The process uses mechanically milled Nd-Fe-B melt-spun flakes as feedstock powder that is packed into a metal vessel and then hot rolled to form a fully dense and highly textured strip magnet with tailored thicknesses, down to 800 µm. Finally, using this process, fully dense nanograin bulk magnets can be synthesized in minutes compared to the traditional multi-step processes that are typically low throughput.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of different grain boundary diffusion alloys on magnetic properties of Dy-free sintered NdFeB magnet

Dy-free sintered magnets were fabricated by blending Neo powder with different grain boundary diffusion alloy powders. Cu, CeAl and CeAlCu have a negative effect on H cj of magnets, while PrAlCu and AlCuGa have a positive effect. The PrAlCu-added magnet achieves the best magnetic properties among all magnets with the additions of different diffusion alloys. With increasing PrAlCu from 0-10 wt.%, H cj of the magnets gradually increases from the original 14.5 kOe to 19.2 kOe. The magnet with 7.5 wt.% PrAlCu obtains a H cj of 18 kOe and (BH) max of 39.1 MGOe. It is found that Pr and Cu in PrAlCu alloy is mainly distributed at grain boundary and triple junctions, leading to a reduced coupling among grains, thus an enhanced H cj . Here, the grain boundary engineering by adding an appropriate alloy is an effective method to improve H cj of Dy-free NdFeB magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of Post-sintering Annealing on (NdLa)-(FeCo)-B Magnets

A common limitation of La substitutions into (Nd, La) 2 Fe 14 B magnets is the reduction of the anisotropy field (H a ), which decreases magnet coercivity (H cj ). In this study, adding a small amount of Pr-Cu to a La-containing neo magnet may modify the grain boundary (GB), which can help recover a fraction of the degraded H cj . An optimal GB modification requires a carefully designed post-sinter heat treatment, which is the focus of this work on characterizing the effects of multi-step post-sintering annealing on the evolutions of microstructure and magnetic properties. We find that Nd and Cu concentrations at GBs and triple junctions (TJs) increase when the annealing temperatures are lowered. Annealing temperatures of 580°C and 480°C (near rare-earth-rich eutectic temperatures) enabled the development of a thick and continuous GB phase, which helps to magnetically decouple the grains, and, thus, enhance H cj . For the alloy with 25% Nd replaced by La, and with the addition of 7.5 wt.% of Pr 68 Cu 32 as GB modifier, the optimized multi-step post-sinter annealing improved the H cj from 4.8 kOe to 9 kOe.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rapid solidified ductile Cu-Al-Mn ribbon and its elastocaloric potential

Abstract Cu-Al-Mn alloys display martensitic transformation over a wide range of temperatures. In addition to low cost, this alloy is known for its low transformation stress with reasonable latent heat favoring elastocaloric applications. However, the ductility of Cu-Al-Mn can be limited owing to ordering and intergranular fracture. Through rapid solidification by melt spinning, we show that Cu-Al-Mn ribbon can be made highly ductile (greater than 8% tensile strain in the as-spun state and 10% tensile strain after heat treatment). The ductility of the melt-spun ribbon is related to the suppression of L2 1 ordering that is characterized through magnetic property measurement. Heat treatment of the ribbon promotes bamboo grain formation, and the latent heat is increased to 6.4 J g −1 . Under tensile conditions, we show that the ribbon exhibited about 4 °C temperature change (4.4 °C on heating and 4.2 °C on cooling from 6.3% strain).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Manufacturing Processes for Permanent Magnets: Part II—Bonding and Emerging Methods

Abstract Permanent magnets produce magnetic fields and maintain the field even in the presence of an opposing magnetic field. They are widely used in electric machines, electronics, and medical devices. Part I reviews the conventional manufacturing processes for commercial magnets, including Nd-Fe-B, Sm-Co, alnico, and ferrite in cast and sintered forms. In Part II, bonding, emerging advanced manufacturing processes, as well as magnet recycling methods are briefly reviewed for their current status, challenges, and future directions.

Cui, Jun (ORCID:0000000179118172)↗
DOE OSTI2022

Manufacturing Processes for Permanent Magnets: Part I—Sintering and Casting

Abstract Permanent magnets (PMs) produce magnetic fields and maintain the field even in the presence of an opposing magnetic field. Electrical machines using permanent magnets are more efficient than those without. Currently, all known strong magnets contain rare earth (RE) elements, and they are core components of a wide range of applications including electric vehicles and wind turbines. RE elements such as Nd and Dy have become critical materials due to the growing demand and constrained supply. Improving the manufacturing process is effective in mitigating the RE criticality issue by reducing waste and improving parts consistency. In this article, the state of the industry for PM is reviewed in detail considering both the technical and economic drivers. The importance of RE elements is discussed along with their economic importance to green energy. The conventional sintering and casting manufacturing processes for commercial magnets, including Nd-Fe-B, Sm-Co, Alnico, and ferrite, are described in detail.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Enhanced electrical conductivity in graphene–copper multilayer composite

For many years, researchers have been trying to make a material more conductive than silver by incorporating carbon nanotubes or graphene into copper to form a composite material. However, after a decade-long effort, only a few groups reported successful results, raising concerns about the feasibility of this composite approach. Here, we report our effort to validate the multilayer graphene–copper composite approach for improving electrical conductivity. We demonstrate that, with an estimated 0.008 vol. % graphene addition, copper’s electrical conductivity was improved to 104.2% of International Annealed Copper Standard (IACS) at room temperature. If the copper substrate used to make the multilayer composite is discounted using the parallel resistance model, the conductivity is calculated to be 185% IACS. This result could be further improved if the thickness of the copper layers can be further reduced.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Elastocaloric effect in vanadium (IV) oxide

Elastocaloric cooling utilizes the latent heat associated with stress-induced reversible phase transformations to achieve cooling. Currently, the key barrier to this technology is its prohibitive cost due to the high elastocaloric material cost and the large stress required to drive the cooling cycle. Vanadium (IV) oxide (VO 2 ) is a good candidate, and it is relatively cheap. Our calorimetry study shows it exhibits a reversible phase transformation with a large latent heat of 31.5 J/g, as well as excellent functional stability. Its transformation temperature and latent heat are tunable via heat treatment. We demonstrated that VO 2 powders can be cyclically compressed in a steel tube using a steel plunger to drive the elastocaloric effect. The application of relatively low stress of 300 MPa is sufficient to result in a reversible temperature change of 0.5 °C on the powder compact. Further improvement of reversible temperature change to 1.6 °C under 300MPa is achieved by adding conductive copper powders. Future efforts should focus on improving material properties such as heat capacity and thermal conductivity for candidate ceramic oxides to maximize elastocaloric effects.

36 MATERIALS SCIENCE↗