Engineering Papers⌕ Search

Engineering topics

Ozcan, Soydan

Publications and source records attributed to Ozcan, Soydan.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High-strength 3D printed poly(lactic acid) composites reinforced by shear-aligned polymer-grafted cellulose nanofibrils

This work demonstrates the application of pilot-scale surface functionalization of cellulose nanofibrils (CNFs) by aqueous grafting-through polymerization and subsequent spray drying in 3D printed poly(lactic acid) (PLA) composites. Grafted-CNF composites attain an ultimate tensile strength of 88 ± 3 MPa and a tensile modulus of elasticity of 7.8 ± 1.3 GPa in the printing direction at 20 wt% reinforcement loading. These increases, 42% and 139% over neat PLA, respectively, represent the strongest reported 3D printed CNF/PLA composite to date in the literature. The mechanisms behind these improvements are investigated by comparisons to neat PLA and unmodified spray-dried CNF/PLA controls using melt rheology, dynamic mechanical analysis, and assessment of the reinforcement dispersion. These experiments reveal that improved network formation and shear-induced alignment of the grafted CNFs facilitate the remarkable tensile properties of the printed composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effect of plasma treatment on LMPAEK/CF tape and composites manufactured by automated tape placement (ATP)

Automated tape placement (ATP) process is widely used in aerospace for its advanced process control and multi-axis capabilities but faces issues like limited choice of materials and suboptimal tape consolidation. This study investigates air plasma treatment on ATP carbon fiber thermoplastic feedstock tape to address these challenges. The effects on low melt Polyaryletherketone/carbon fiber unidirectional tape (LMPAEK/CF UD tape) were analyzed. Treated and untreated tapes were used to fabricate composites and evaluated for physical, thermal, mechanical, and interfacial properties. Atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) analyses revealed surface roughness changes (on LMPAEK), extent of oxidation, and the presence of hydroxyl/carboxyl groups. Composites from plasma-treated tapes showed a 7.6% increase in tensile strength, 8% in tensile modulus, 18% in flexural strength, and 8.3% in flexural modulus. Further, the interlaminar shear strength improved by 18.7%. Failure analysis showed untreated composites failed via inter-ply and fiber-matrix delamination, while treated composites experienced matrix cracking and fiber breakage. This study highlights atmospheric plasma treatment as a solution to ATP’s limitations, significantly enhancing LMPAEK/CF UD tape composites’ properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exploiting the Properties of Non-Wood Feedstocks to Produce Tailorable Lignin-Containing Cellulose Nanofibers

Lignin-containing cellulose nanofibrils (LCNFs) are mainly produced commercially from treated wood pulp, which can decrease some of the carbon-negative benefits of utilizing biomass feedstock. In this work, LCNFs are prepared from non-wood feedstocks, including agricultural residues such as hemp, wheat straw, and flax. These feedstocks allowed for the preparation of LCNFs with a variety of properties, including tailored hydrophobicity. The feedstocks and their subsequent LCNFs are extensively characterized to determine the roles that feedstocks play on the morphology and properties of their resultant LCNFs. The LCNFs were then incorporated into paper handsheets to study their usefulness in papermaking applications, which indicated good potential for the use of wheat straw LCNFs as a surface additive to improve the oil resistance coating.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Molecular-level design of alternative media for energy-saving pilot-scale fibrillation of nanocellulose

The outstanding mechanical properties, light weight, and biodegradability of cellulose nanofibrils (CNFs) make them promising components of renewable and sustainable next-generation reinforced composite biomaterials and bioplastics. Manufacturing CNFs at a pilot scale requires disc-refining fibrillation of dilute cellulose fibers in aqueous pulp suspensions to shear the fibers apart into their nanodimensional forms, which is, however, an energy-intensive process. Here, in this study, we used atomistic molecular dynamics (MD) simulation to examine media that might facilitate the reduction of interactions between cellulose fibers, thereby reducing energy consumption in fibrillation. The most suitable medium found by the simulations was an aqueous solution with 0.007:0.012 wt.% NaOH:urea, and indeed this was found in pilot-scale experiments to reduce the fibrillation energy by ~21% on average relative to water alone. The NaOH:urea-mediated CNFs have similar crystallinity, morphology, and mechanical strength to those formed in water. The NaOH and urea act synergistically on CNFs to aid fibrillation but at different length scales. NaOH deprotonates hydroxyl groups leading to mesoscale electrostatic repulsion between fibrils, whereas urea forms hydrogen bonds with protonated hydroxyl groups thus disrupting interfibril hydrogen bonds. This suggests a general mechanism in which an aqueous medium that contains a strong base and a small organic molecule acting as a hydrogen-bond acceptor and/or donor may be effectively employed in materials processes where dispersion of deprotonable polymers is required. The study demonstrates how atomic-detail computer simulation can be integrated with pilot-scale experiments in the rational design of materials processes for the circular bioeconomy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A review of antimicrobial implications for improving indoor air quality

The frequent outbreak of infectious respiratory diseases, such as the recent COVID-19 epidemic, raised the importance of indoor air quality. Removing microorganisms from indoor air is critical to improve indoor air quality. Numerous studies in recent years have been published on developing antimicrobial materials and technologies for antibacterial and antiviral applications. Further, this study critically reviews the recent antimicrobial advances for improving indoor air quality. This paper provides a comprehensive analysis of the antimicrobial mechanisms, development of materials, and deployment strategies, as well as a performance evaluation of the antimicrobial implication for indoor air quality. Furthermore, the challenges and opportunities of future research directions are also highlighted.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Effects of mercerization and fiber sizing of coir fiber for utilization in polypropylene composites

The use of natural fibers as an alternative to synthetic fibers for reinforcing composites is increasing. However, the poor interfacial adhesion between natural fibers and polymer matrices limits their applications. Several approaches have been considered to improve fiber-matrix adhesion via chemical and/or physical treatment. However, the effectiveness of these treatments varies based on the type of fiber, its source, and its composition. Thus, it is imperative to understand the effectiveness of treatment conditions. In this study, we investigated the influence of alkali treatment and fiber sizing on the chemical, thermal, morphological, and mechanical properties of coir fibers and the interface between coir fiber and polypropylene matrix. Further, it was found that using a 5 wt% sodium hydroxide solution for 6 h at room temperature was the optimal treatment condition that led to an improvement in tensile strength by 58%, tensile modulus by 71%, and elongation at break by 37% compared to untreated fibers, and an increment in interfacial shear strength (IFSS) between coir fibers and polypropylene matrix by 32%. The alkali treatment removed the fiber surface impurities, made the fiber surface rough, and enhanced the fiber crystallinity. Sizing of the alkali-treated fiber led to an improvement in IFSS by 87% with no modification of the fiber’s mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D printing synthesis of catalysts

The catalyst industry generates approximately $20 billion every year globally and plays a major role in the energy production sector. Traditional industrial catalysts (e.g., pellets) typically have mass and heat transfer limitations, and cause a pressure drop in continuous-flow reactors, lowering the efficiency of the catalytic processes. 3D printing technology has evolved rapidly over the past decade, and the 3D printing of catalysts with desired geometries can address many of the above-stated challenges with traditional catalysts. However, challenges remain to be addressed and opportunities remain to be explored before the full potential in the design and 3D printing of novel catalysts can be realized. Herein this article reviews the recent development in the 3D printing of catalysts. It summarizes the 3D printing design, dimension, property, and performance of 3D printed catalysts. The applications of 3D printed catalysts, such as reforming, wastewater treatment, and CO 2 capture and removal, are discussed, with a techno-economic analysis and life cycle analysis. Future research directions and opportunities for 3D printing of catalysts are also highlighted.

25 ENERGY STORAGE↗
DOE OSTI2024

Long coir and glass fiber reinforced polypropylene hybrid composites prepared via wet-laid technique

Natural fiber composites offer an advantage in terms of weight saving for many automotive applications; however, many natural fiber composites lack properties to justify substitution for synthetic composites. Hybridizing the natural fiber composites by adding a fraction of synthetic fibers is an innovative approach to provide a balance between composite's performance and weight savings. In this study, coir fiber (40 wt%)-reinforced polypropylene (PP) composites were hybridized by substituting a fraction of coir fiber with glass fiber (0–30 wt%). The composites were prepared using a novel wet-laid technique followed by compression molding, where the fiber length is preserved. The composites prepared by hybridizing PP/coir fibers with glass fibers were light in weight (6–20% lighter compared to 40 wt% glass fiber reinforced PP) with significantly enhanced tensile (strength – 49–182%, modulus – 54–130%), flexural (strength – 41–104%, modulus – 64–193%), and impact properties (157 - 474%) compared to 40 wt% coir fiber reinforced PP composites. Furthermore, the addition of glass fiber (10–30 wt%) to coir fiber reduced the water-absorbing tendency (by 18–74%) of PP/coir fiber composites. All in all, this work has potential applications in automotive, mass transit, and truck applications where natural fiber composites are being investigated as alternatives to metal and/or fully synthetic composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Recycling of CF-ABS machining waste for large format additive manufacturing

Large format additive manufacturing (LFAM) necessitates the use of short fiber thermoplastic composites, such as carbon fiber filled acrylonitrile butadiene styrene, to enable printing. Currently, when LFAM parts are machined into their final shape, the machining scrap (i.e., small flake like particles and offcuts) is landfilled. Previous studies have demonstrated the viability of recycling end-of-life LFAM parts by shredding and optionally re-compounding the material back into pellets. However, there is little understanding of the value and performance of recycled material made from LFAM machining scrap, which if pursued could motivate more broad recycling of this waste stream. In this study, recycled in-process machining scrap is explored as an LFAM feedstock source. Herein, it is found that the primary degradation mechanism of the recycled material is significant fiber length attrition during surface machining. While this fiber attrition negatively impacts the mechanical performance of the material in the print direction, it seems that the changes in processing behaviors and print quality, namely the surface roughness of the printed structure associated with shorter fiber lengths, is beneficial to interlayer adhesion. The tensile strength and elastic modulus of the recycled material, in the print direction, decreased 11% and 31% respectively compared to the pristine material. However, in the layer-wise direction it was found that the recycled material exhibited no significant change in elastic modulus and a significant 21% increase in tensile strength – a surprising result. In conclusion, this work indicates that machining waste could be a viable material stream for recycled LFAM feedstock materials.

42 ENGINEERING↗
DOE OSTI2024

Effect of Internal Structure on Warpage in a Large-Scale Additive Manufacturing Process With Bio-Derived Composites

Extrusion-based large-format additive manufacturing (LFAM) often results in unintended deformation and failures due to thermal residual stress between layers. This LFAM involves a hot molten polymer deposited on a previously deposited and cooled layer, generating a temperature mismatch between the layers. The temperature discrepancy causes a thermal contraction mismatch, generating thermal residual stress. Due to the residual stress, printed structures experience warpage and delamination Therefore, understanding the heat distribution behavior is essential to preventing undesired deformation and failures. The goal of this study is to investigate the effect of infill patterns on heat distribution and deformation in an LFAM system. Wood fiber-reinforced polylactic acid was used as a sustainable and low-cost reinforcement material. A numerical model was developed to predict the temperature and deformation field with thermo-mechanical properties, which were measured by a dynamic mechanical analysis and a thermal expansion test. Simulations were performed on a box geometry with three different infill patterns. The simulation model was verified with temperature data gathered from an infrared camera. The results show good agreement between predicted and measured temperature profiles. The developed simulation model was applied to a roof tray with different infill patterns for a case study. We found that the different thermal mass distributions resulting from the various infill patterns affected the heat distribution and deformation. These findings contribute to a better understanding of the thermal and mechanical behavior of LFAM.

Jo, Eonyeon↗
DOE OSTI2023

Effect of recycled fibers and shredded intermediates variation on the mechanical properties and energy absorption of fiber‐reinforced composite panels

Abstract The global composite industry generates large quantities of waste which mostly ends up in landfills due to a lack of established end‐use applications for multiple waste streams. The scrap from end‐of‐life (EoL) includes manufacturing waste such as dry chopped fiber tows, loose fibers, shredded fibers from fabric textile operations, cured/semi‐cured prepregs, and fully cured composite structure waste from aircraft, automobiles, wind blades, boats, and pressure vessels. In this work, different composite waste streams were reduced to shredded intermediates, followed by simple blending, and subjected to wet compression molding to produce composite panels. The panels/plaques were tested for mechanical properties (flexure and impact), fiber‐matrix wet‐out, and property bounds. It was found that wet‐compression molding was a viable and scale‐able approach to produce recycled panels from EoL composites shredded scrap. Furthermore, full‐scale size panels for use in truck bodies and intermodal shipping container flooring were manufactured and their impact resistance was tested using a drop weight impact test. They were tested both for high‐ and low‐velocity load. In the case of high‐velocity load, the average impact load was 14,673 N; the average absorbed energy was 101.6 J; the average elastic energy was 11.7 J and the impact resistance was 1065 J/m. In the case of the low‐velocity drop weight impact test, it was found that the average impact load was 7877.358 N; the average absorbed energy was 9.718 J; the average elastic energy was 9.14 J, and the impact resistance was 184.1 J/m. The shredded composite was shown to be a candidate material for the manufacture of truck bodies and intermodal containers’ flooring panels. Highlights By using shredded intermediates from different composite waste streams, it is possible to manufacture composite panels. Wet–compression process is an appropriate technique for manufacturing recycled fiber composite panels. Regardless of the source of scrap, the mechanical properties of the produced composite panels were improved. The recycling process technology can be transformed to commercial scale to produce full‐size transportation flooring panels. A product pathway is established in consideration of lower cost and improved recyclability.

Vaidya, Uday↗
DOE OSTI2023

Wind Turbine Blade Repurposing and Recycling: Coupling Repurposing Methods with 3D Printing Technology

Fiber-reinforced thermoplastic composites continue to be implemented in several marketsbecause of their strength capacity and light weight. Especially in the wind industry, wind bladesare made of this material which makes them ideal for wind energy generation, but bladesbecome a problem at end-of-life. Because recycling thermoplastic composites technologiesare still not cost and environmentally effective, research in this space is needed. This paperpresents a case study for coupling repurposed wind turbine blades and 3D printing technology.The purpose is to remanufacture decommissioned wind blades into bus stop roof and seatingsections to then use recycled glass fiber from a decommissioned wind turbine blade to 3Dprint structural and/or fixtures needed in the assembly. We provide an overview of the designprocess, and the development process steps in repurposing and 3D printing the material,delving into key parameters required for a successful implementation.

Henao, Yulizza↗
DOE OSTI2023

Silicon carbide fiber manufacturing: Cost and technology

Significant advances have been made in the past decade concerning silicon carbide fiber manufacturing methods resulting in near-stoichiometric small-diameter fibers that meet the property requirements for most of the ceramic matrix composites (CMC) and nuclear applications. The manufacturing cost, however, remained prohibitively high, preventing the use of it in different applications requiring much lower cost. Silicon carbide (SiC) fiber reinforced CMC is dominated by the cost of SiC fiber which comprises more than 50 % of the finished part cost. Here, this article provides insight into the SiC fiber manufacturing costs and highlights the need for an alternative SiC fiber precursor and manufacturing method. Analysis of the existing polycarbosilane (PCS)-based SiC fiber manufacturing shows that the crosslinking (curing) and raw material preparation steps are high-cost steps that need lower cost options. Alternative SiC fiber precursor should be sought for lowering the cost of SiC fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of fiber reinforcement on the process parameters of injection molding manufacturing process

Use of fillers with the resin is common in injection molding manufacturing technique to enhance the stiffness and strength of the manufactured components. However, the addition of fillers changes the rheological and mechanical properties of the material, required adjustments in the process parameters used for the manufacturing. The present study aims to investigate this impact of fillers on the process parameters of the injection molding manufacturing process. Neat Acrylonitrile Butadiene Styrene (ABS) and ABS reinforced with short glass fibers are used as the materials to perform the comprehensive numerical analysis including complete process sequence, namely filling, packing, cooling and warpage. Parametric studies are conducted to optimize the manufacturing process for minimal warpage (or shrinkage) in the produced part. The selected process parameters for the parametric study include cooling time, packing pressure, and mold temperature, all of which directly impact the quality of the manufactured parts. The optimal values obtained for these parameters are compared to examine the effect fiber reinforcement has on the manufacturing process.

Garg, Nikhil↗
DOE OSTI2023

Life cycle cost, energy, and carbon emissions of molds for precast concrete: Exploring the impacts of material choices and additive manufacturing

Molds for precast concrete are commonly used to create simple- to complex-shaped concrete products away from construction sites. These molds are often handmade from wood; however, additively manufacturing (AM, or 3D printing) fiber-reinforced polymer composites is an advantageous alternative, producing significantly more durable, highly complex molds faster, but likely at a higher cost. Here, this study explores the impact of material and production variables on the cost, energy, and carbon emissions of employing composite AM molds over the full lifecycle. The case study employed techno-economic and life cycle assessments to show that using wood flour–poly(lactic acid) or recycled carbon fiber–acrylonitrile butadiene styrene for AM molds can be less expensive than conventional wood molds, especially when considering use phase costs. While wood molds have the least environmental impacts due to wood's higher biogenic carbon sequestration and minimal processing, optimizing AM designs could reduce energy demand, carbon emissions, and cost.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additively manufactured polymer composites for heat exchanger applications: evaluation of critical thermophysical properties

Polymeric heat exchangers (PHXs) have been used in applications involving weight restrictions, chemical compatibility, and fouling issues. Additive manufacturing (AM) or 3D printing provide new solutions to previously inaccessible combinations of properties and geometries. There are some advancements in the PHXs by AM; however, the process and the properties of materials still need further investigation to improve the overall performance. In this study, additively manufactured polyethylene terephthalate glycol (PETG) composites reinforced with graphite and pitch-based carbon fibers were evaluated for their potential application as PHXs. The thermal conductivity, volumetric heat capacity, coefficient of thermal expansion, creep behavior, and long-term performance were studied in detail. Our results reveal that the composites have an anisotropic thermal conductivity. The thermal conductivity along the printing direction is higher than the layer building direction due to the shear-induced alignment of the fillers. The printed composites achieve good thermal stability with 80% lower CTE at room temperature than neat PETG. Creep tests suggest the creep and creep recovery were highly temperature-dependent, and the deformation can be recovered when the temperature is below glass transition. These results suggest additive manufactured composites be potentially used for heat exchanger applications at low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Bioinspired design toward nanocellulose-based materials

Nature provides lots of inspiration for material and structural design for various applications. Deriving design principles from the investigation of nature can provide a rich source of inspiration for the development of multifunctional materials. The bioinspired design templates mainly include mussels, nacre, and various plant species. As a sustainable and renewable feedstock, nanocellulose can be used to fabricate advanced materials with multifunctional properties through bioinspired designs. However, challenges and opportunities remain for realizing the full potential in the design of novel materials. Here, this article reviewed recent development in the bioinspired nanocellulose based materials and their application. This article summarizes the functions (e.g., surface wetting) and applications (e.g., composite) of bioinspired nanocellulose-based materials. The bioinspired design templates are discussed along with strategies, advantages, and challenges to the development of synthetic mimics. Additionally, mechanisms and processes (e.g., chemical modification, self-assembly) leading to biomimetic design are discussed. Finally, future research directions and opportunities of bioinspired nanocellulose-based materials are highlighted.

36 MATERIALS SCIENCE↗