Effect of thermomechanical processing on mechanical properties and the microstructure of binary Al-Ce alloy
Not Available
Singh, Gaurav (ORCID:0000000311445016)↗
Engineering topics
Ouyang, Gaoyuan
Publications and source records attributed to Ouyang, Gaoyuan.
Hot-Roll Fabrication of Anisotropic Nanograin Nd-Fe-B Magnet
Nd-Fe-B based magnets have the highest energy product among all permanent magnets, which is required for numerous clean energy technologies. For higher temperature applications (T > 150°C), additions of heavy rare earth elements (HREEs) such as Dy are required to maintain sufficient coercivity during operation. Additions of Dy are expensive. Thus, it is desirable to reduce the need for HREEs by reducing the grain size to the nanoscale, which increases the coercivity and decreases its temperature dependence. Here, we report a novel nanograin Nd-Fe-B magnet fabrication method that is continuous and inexpensive. The process uses mechanically milled Nd-Fe-B melt-spun flakes as feedstock powder that is packed into a metal vessel and then hot rolled to form a fully dense and highly textured strip magnet with tailored thicknesses, down to 800 µm. Finally, using this process, fully dense nanograin bulk magnets can be synthesized in minutes compared to the traditional multi-step processes that are typically low throughput.
36 MATERIALS SCIENCE↗
Predictive design of novel nickel-based superalloys beyond Haynes 282
Nickel-based superalloys are in great demand for harsh-service conditions involving high temperatures and oxidative environments. Haynes 282 stands out due to its excellent high-temperature properties and easy fabricability. However, the upper operation temperature of Haynes 282 is limited due to its relatively low liquidus temperature. Equipped with high-fidelity density-functional theory calculations and high-throughput experimentation methodology, we explored new compositional spaces that exhibit higher liquidus temperature and higher strength. While maintaining the manufacturability, the newly designed alloy shows improved strength and ductility at room temperature and better oxidation resistance up to 800°C. Here, the new compositions showcase a minor change in the refractory and metalloid content can significantly impact the mechanical and oxidation performance of superalloys.
36 MATERIALS SCIENCE↗
Theory-guided design of duplex-phase multi-principal-element alloys
Density-functional theory (DFT) is used to identify phase-equilibria in multi-principal-element and high-entropy alloys (MPEAs/HEAs), including duplex-phase and eutectic microstructures. Here, a combination of composition-dependent formation energy and electronic-structure-based ordering parameters were used to identify a transition from FCC to BCC favoring mixtures, and these predictions experimentally validated in the Al-Co-Cr-Cu-Fe-Ni system. A sharp crossover in lattice structure and dual-phase stability as a function of composition were predicted via DFT and validated experimentally. The impact of solidification kinetics and thermodynamic stability was explored experimentally using a range of techniques, from slow (castings) to rapid (laser remelting), which showed a decoupling of phase fraction from thermal history, i.e., phase fraction was found to be solidification rate-independent, enabling tuning of a multi-modal cell and grain size ranging from nanoscale through macroscale. Strength and ductility tradeoffs for select processing parameters were investigated via uniaxial tension and small-punch testing on specimens manufactured via powder-based additive manufacturing (directed-energy deposition). This work establishes a pathway for design and optimization of next-generation multiphase superalloys via tailoring of structural and chemical ordering in concentrated solid solutions.
36 MATERIALS SCIENCE↗
Predictive design of novel nickel-based superalloys beyond Haynes 282. Final Report FWP-AL-19-510-097
Nickel-based superalloys are in great demand for harsh-service conditions involving high temperatures and oxidative environments. Haynes 282 stands out due to its excellent high-temperature properties and easy fabricability. However, the upper usage temperature of Haynes 282 is limited due to its relatively low liquidus temperature. Through high-fidelity density functional theory calculations and high-throughput experiments, new compositions that show higher liquidus temperature and higher strength are explored. While maintaining processability, the newly designed alloy shows improved strength and ductility at room temperature and better oxidation resistance up to 800°C. The new compositions showcase a minor change in the refractory and metalloid content can have a significant impact on the mechanical and oxidation performance of superalloys.
36 MATERIALS SCIENCE↗
The Addition of Boron to Melt-Spun Fe-6.5%Si Ribbons
Fe-6.5%Si has higher electrical resistivity, lower magnetocrystalline anisotropy, and lower magnetostriction than traditional Fe-3.2%Si silicon steel. The reduced iron losses of Fe-6.5%Si render it a highly favorable candidate for high-speed motors and transformers. However, large-scale production of wide Fe-6.5%Si tape by rapid solidification can be challenging mainly because of its high melting point. In this work, boron is alloyed to Fe-6.5%Si to reduce its melting temperature and interfacial energy to improve the alloy’s processability. Boron additions from 0.01 wt.% to 2.24 wt.% into Fe-6.5%Si and its effect on ribbon thickness, grain size, magnetic, and mechanical properties were studied. Further, minor boron alloying significantly changed the melt pool stability and wetting on the quench wheel and in turn increased the quench rate with minimum impact on the magnetic saturation and ductility. Boron addition of < 0.06 wt.% was also found beneficial to the magnetic property of the alloy by lowering both its hysteresis and eddy current losses.
36 MATERIALS SCIENCE↗
A ductility metric for refractory-based multi-principal-element alloys
We propose a quantum-mechanical dimensionless metric, the local-lattice distortion (LLD), as a reliable predictor of ductility in refractory multi-principal-element alloys (RMPEAs). The LLD metric is based on electronegativity differences in localized chemical environments and combines atomic-scale displacements due to local lattice distortions with a weighted average of valence-electron count. To evaluate the effectiveness of this metric, we examined body-centered cubic (bcc) refractory alloys that exhibit ductile-to-brittle behavior. Our findings demonstrate that local-charge behavior can be tuned via composition to enhance ductility in RMPEAs. With finite-sized cell effects eliminated, the LLD metric accurately predicted the ductility of arbitrary alloys, which compares well with existing tensile-elongation experiments. To validate further, we qualitatively evaluated the ductility of two refractory RMPEAs, i.e., NbTaMoW and Mo 72 W 13 Ta 10 Ti 2.5 Zr 2.5 , through the observation of crack formation under indentation, again showing excellent agreement with LLD predictions. Additionally, a comparative study of three refractory alloys provides further insights into the electronic-structure origin of ductility in refractory RMPEAs. This proposed metric enables rapid and accurate assessment of ductility behavior in the vast RMPEA composition space.
36 MATERIALS SCIENCE↗
Development of Dy-free Nd-Fe-B-based sintered magnet through grain boundary engineering using Pr-Cu alloys
For this study, Dy-free sintered magnets were fabricated by mixing Nd-Fe-B powder with various amounts of Pr-Cu powder followed by the common procedures for making Nd-Fe-B based sintered magnets. With the Pr-Cu addition increasing from 0 to 10 wt.%, the obtained magnets’ H cj increases from the original 14.5 kOe to 18.6 kOe. The highest (BH) max achieved was 35.0 MGOe with 7.5 wt.% PrCu. The distribution of the Pr and Cu elements was primarily at grain boundary and triple junctions, leading to a reduced coupling among grains, thus an enhanced H cj .
36 MATERIALS SCIENCE↗
Oxidation mechanism in a refractory multiple-principal-element alloy at high temperature
Refractory multiple-principal-element alloys (RMPEAs) are promising structural materials to enable increased power efficiency in high-temperature oxidation environments, but the oxidation behavior and microstructures of the oxides, especially at the beginning of the oxidation, have received limited attention. Here, the oxidation mechanism in an equimolar W-Mo-Ta-Nb-V was investigated at 1300 °C and compared with the equimolar W-Mo-Ta-Nb alloy without V. The oxide scale on WMoTaNbV after 1 min exposure is shown to be composed of a degradation layer at the interface of the alloy/oxide, an initial oxide transition layer, followed by the main phase aggregate oxide layer, and an outermost oxide layer. At the early stage of oxidation, the absorption of oxygen by the RMPEA substrate forms a solid solution. Vanadium accelerates the initial degradation process as it forms VO. The initial oxidation-induced degradation of RMPEA follows a sequence governed by the free energy change accompanied by local element segregation. Liquid V-Mo oxides aggregate in the intermediate oxide layer. The inward growth of the oxide scale is controlled by the local composition changes, the orientation of the substrate, the crystal structure, and physical properties such as melting points of the oxides.
36 MATERIALS SCIENCE↗
Boosting the H 2 –D 2 Exchange Activity of Dilute Nanoporous Ti–Cu Catalysts through Oxidation–Reduction Cycle–Induced Restructuring
The use of nanoporous metals as catalysts has attracted significant interest in recent years. Their high-curvature, nanoscale ligaments provide not only high surface area but also a high density of undercoordinated step edge and kink sites. However, their long-term stability, especially at higher temperatures, is often limited by thermal coarsening and the associated loss of surface area. Herein, it is demonstrated that the nanoscale morphology of nanoporous Cu can be regenerated by applying oxidation/reduction cycles at 250 °C. Specifically, the morphological evolution and H 2 dissociation activity of hierarchical nanoporous Cu catalysts doped with Ti during structural rearrangement triggered by oxidative and reductive atmospheres at elevated temperatures are studied. In addition to coarsening of the structure at elevated temperatures, oxidation at 400 °C causes an expansion of the ligaments. Further, subsequent reduction at 400 °C leads to the formation of particles and a drop in the H 2 dissociation activity compared the fresh catalyst. However, performing the redox cycle at 250 °C reverses coarsening and boosts the H 2 dissociation activity for the hydrogen–deuterium (H 2 –D 2 ) reaction. Herein, the possibility to reverse coarsening is demonstrated, thereby mitigating the loss of activity frequently observed in nanoporous catalysts.
36 MATERIALS SCIENCE↗
Engineering microstructure to improve coercivity of bulk MnBi magnet
MnBi is a candidate material for high-temperature magnets because of its increasing coercivity with increasing temperatures up to 255 °C. However, most efforts in fabricating bulk MnBi magnets have run into the problem of preserving the coercivity (H cj) of its feedstock powders. About 70% of powder’s H cj would be lost during the densification process. Our micromagnetic modeling shows that the coercivity mechanism of the MnBi bulk magnet is controlled by nucleation of the reversal magnetization domains, and the large H cj loss that occurred during the powder consolidation process can be attributed to the inter-grain magnetic coupling. To attain a high H cj , the grains in the MnBi bulk magnet must be separated with a non-magnetic grain boundary phase (GBP). To validate this GBP hypothesis, we engineered MnBi bulk magnets with two different types of GBP. The first type of GBP was created in-situ by precipitating excessive Bi from the grains; the second type was created ex-situ by coating silicates on the feedstock powders before the consolidation. While both GBP work, the ex-situ approach resulted in a better H cj due to a more uniform GBP distribution. We report the H cj loss was reduced from 70% to 15%, and the (BH)max of a warm sintered bulk magnet reached 8.9 MGOe.
36 MATERIALS SCIENCE↗
Sprayable copper and copper–zinc nanowires inks for antiviral surface coating
SEM and TEM images of copper and copper–zinc nanowires that are sprayable for antiviral surface coating.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Enhanced electrical conductivity in graphene–copper multilayer composite
For many years, researchers have been trying to make a material more conductive than silver by incorporating carbon nanotubes or graphene into copper to form a composite material. However, after a decade-long effort, only a few groups reported successful results, raising concerns about the feasibility of this composite approach. Here, we report our effort to validate the multilayer graphene–copper composite approach for improving electrical conductivity. We demonstrate that, with an estimated 0.008 vol. % graphene addition, copper’s electrical conductivity was improved to 104.2% of International Annealed Copper Standard (IACS) at room temperature. If the copper substrate used to make the multilayer composite is discounted using the parallel resistance model, the conductivity is calculated to be 185% IACS. This result could be further improved if the thickness of the copper layers can be further reduced.
36 MATERIALS SCIENCE↗
Machine learning assisted prediction of the Young’s modulus of compositionally complex alloys
We identify compositionally complex alloys (CCAs) that offer exceptional mechanical properties for elevated temperature applications by employing machine learning (ML) in conjunction with rapid synthesis and testing of alloys for validation to accelerate alloy design. The advantages of this approach are scalability, rapidity, and reasonably accurate predictions. ML tools were implemented to predict Young’s modulus of refractory-based CCAs by employing different ML models. Our results, in conjunction with experimental validation, suggest that average valence electron concentration, the difference in atomic radius, a geometrical parameter λ and melting temperature of the alloys are the key features that determine the Young’s modulus of CCAs and refractory-based CCAs. The Gradient Boosting model provided the best predictive capabilities (mean absolute error of 6.15 GPa) among the models studied. Our approach integrates high-quality validation data from experiments, literature data for training machine-learning models, and feature selection based on physical insights. It opens a new avenue to optimize the desired materials property for different engineering applications.
36 MATERIALS SCIENCE↗
Enhanced oxidation resistance of (Mo 95 W 5 ) 85 Ta 10 (TiZr) 5 refractory multi-principal element alloy up to 1300°C
Refractory-metal-based alloys are a potential replacement of current nickel-based superalloys due to their excellent mechanical strength at extremely high temperatures. However, severe oxidation in a high-temperature working environment limits their application. To address this challenge, a two-step coating process (including a Mo precoat and a Si-B pack cementation) was applied to an innovative refractory multi-principal element alloy (RMPEA) (Mo 95 W 5 ) 85 Ta 10 (TiZr) 5 . The coating is composed of an aluminoborosilica glass layer on top of a RMPEA-Si-B multilayered structure. Here, the coating effectively protects the RMPEA from oxidation in high-temperature environments, as demonstrated by phase-stable operation at 10–20% higher temperatures over state-of-the-art systems without any forced-cooling system. Following an isothermal exposure at 1300 °C, the weight change of the coated sample follows a paralinear kinetics with a minor weight loss of 4.2 mg/cm 2 after 50 h. Thermal cycling tests between 1300 °C and room temperature in air resulted in the total weight gain of only 2.6 mg/cm 2 after 450 cycles. The coating shows an excellent adherence to the substrate with a boride layer acting as a barrier that maintains the coating integrity. This two-step Mo-Si-B coating method can be adapted to provide environmental resistance to a wide range of RMPEA.
36 MATERIALS SCIENCE↗
Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys
Compared to the widely used Fe-3.2wt%Si steel, Fe-6.5wt%Si has superior electric and magnetic properties, including higher electrical resistivity, lower iron loss, higher permeability, and near zero magnetostriction. However, Fe-6.5wt%Si sheet is difficult to produce using traditional manufacturing processes as the high silicon content favors the formation of ordered phases that embrittle the material. Fortunately, these ordered phases can be suppressed if the alloy is cooled fast enough from a high temperature kinetically trapping the disordered solid solution or amorphous state. Planar flow casting is known for its rapid solidification rate. In order to consider it as a viable method to manufacture ductile Fe-6.5wt%Si sheets, the effect of cooling rate on physical properties of Fe-6.5wt%Si alloy are systematically investigated. In this work, various cooling rates are achieved by changing melt-spin wheel speeds, which significantly affect the solidification temperature profile and have profound effects on ordering, microstructures, textures, hardness, and magnetic properties. High cooling rates result in refined grains, reduced ordering, enhanced <100> out of the plane texture, decreased hardness, and increased coercivity. This study demonstrates a critical cooling rate at ~1.7 × 10 5 K/s, corresponding to a tangential wheel speed of 5-7 m/s, below which the hardness significantly increases in agreement with the sudden increase of the ordered phases that causes the material embrittlement.
36 MATERIALS SCIENCE↗
Near net shape fabrication of anisotropic Fe-6.5%Si soft magnetic materials
Not Available
36 MATERIALS SCIENCE↗
Magnetic and mechanical properties of grain-refined Dy-free Nd-Fe-B sintered magnets
In this work, the effects of grain size on magnetic and mechanical properties of Dy-free Nd-Fe-B sintered magnets were studied. The grain size of the sintered magnets was varied by using different sized Dy-free Nd-Fe-B alloy feedstock powders which were ball milled to different extents. Increasing the ball milling time from 7 to 11 h caused the average particle size of the powders to decrease from 3.6 to 2.1 µm, while the average grain size of the corresponding sintered magnets decreased from 5.0 to 4.0 µm. The intrinsic coercivity Hcj and maximum energy product (BH) max of these magnets increased from 11.6 to 13.7 kOe and 41.6 to 43.6 MGOe, respectively. The finer grain magnets exhibited better thermal stability, as indicated by a smaller temperature coefficient of H cj (-0.71%/°C). With extending ball milling time to 15 h, the magnetic properties of the magnets deteriorate, while the flexural strengths first decrease and then increase. The flexural strength improvement is attributed to the increased Oxygen content in the magnets due to finer grains. The coercivity enhancement by reduction of grain size is a promising approach to develop Dy-free Nd-Fe-B sintered magnets with better thermal stability. It is important to control the Oxygen contents in the magnets to compromise both magnetic and mechanical properties.
36 MATERIALS SCIENCE↗