Engineering topics
Publications and source records attributed to Ostrach, Simon.
This document is a transcription of the Microgravity Science Research Panel's discussion about their research and about some of the contributions that they feel have been important to the field during their time with the program. The panel includes Dr. Eugene Trinh, Dr. Lawrence DeLucas, Dr. Charles Bugg, Dr. David Larson, and Dr. Simon Ostrach.
Oscillatory thermocapillary flow experiments were performed in the Glovebox aboard the USML-2 Spacelab which was launched on October 20, 1995. Open cylindrical containers of 1.2 and 2.0 cm in diameter were used. The ratio of container depth to radius (aspect ratio) was set at 0.5 and 2. Silicone oil of 2 centistokes kinematic viscosity was the test fluid. The fluid was heated by a cylindrical heater placed along the center axis of the container. The fluid motion was studied by flow visualization. The effect of aspect ratio on the onset of oscillations and on the oscillatory flow was investigated. It was found that the onset of oscillations was delayed when the container was made more shallow.
Results are reported from the Second Surface Tension Driven Convection Experiment (STDCE-2) performed aboard the Second United States Microgravity Laboratory (USML-2), which flew as Space Shuttle mission STS-73 and launched on October 20, 1995. Oscillatory thermocapillary flows were investigated in open cylindrical containers filled with 2 centistokes kinematic viscosity (Pr=27 at 25 C) silicone oil. Two different heating modes were investigated in detail. The main objectives of the experiments were to determine the onset of oscillatory thermocapillary flow under highly reduced buoyancy and gravity conditions and to study the important features of the oscillatory flow. The onset conditions were determined in three different size containers (1.2-, 2-, and 3-cm diameter) and for various free surface shapes (flat and curved). Numerical and scaling analyses were also performed to understand the basic steady flows. The analysis shows that the main flow is viscous-dominated near the onset of oscillations. The onset conditions determined in the present experiments together with our earlier ground-based data show that one could not describe the oscillation phenomenon if the fluid free surface is assumed to be rigid. Therefore, a parameter representing free surface deformation was derived, and the data are shown to be correlated well by that parameter. The oscillation patterns and frequencies are also presented.
The surface tension driven convection experiment-2 (STDCE-2) was conducted onboard the U.S. Microgravity Laboratory (USML)-2 Spacelab which was launched on October 20, 1995. The main objectives of the experiment was to study oscillatory thermocapillary flows in microgravity. Thermocapillary flows were generated in cylindrical test chambers filled with 2 centistokes silicone oil. Six modules were used to study three different chamber diameters and two different heating modes. Tests with both flat and curved free surfaces were conducted. The flow field was studied by flow visualization and an infrared imaging system recorded the oil free-surface temperature. An optical (Ronchi) system was used to measure the oil free-surface deformation and motions. A total of 55 tests were conducted and oscillations were found in most of them. The data are being analyzed.
Gravity dependent transport phenomena in various industrial processes are investigated in order to indicate new directions for micro-gravity research that enhance the commercial success of the space program. The present article describes the commercialization possibilities of such topics associated with physicochemical transport phenomena. The topics are: coating flow, rotating electrochemical system, and convection in low Plandtl number fluids. The present study is directed to understand these phenomena, and to develop a knowledge base for their applications with emphasis to a micro-gravity environment.
Free surface deformation of a test fluid induced by steady and oscillatory thermocapillary flow in a small cylindrical container (diameter = 4.8 mm) is studied experimentally. The fluid (2 Cs oil) is heated by a cylindrical wire (diameter = 0.48 mm) placed along the centerline of the cylinder. The relative displacement and oscillation frequency of free surface are measured in a radial cross-section for various applied temperature differences. It is found that the amplitude of the free surface height oscillations is large near the heater and the cold wall and relatively small in the middle part. The frequency of the free surface oscillations is same as the frequency of the temperature oscillations. Based on these data, the free surface motion during oscillations is delineated.
Gravity-dependent transport phenomena in various industrial processes are investigated in order to address a broader range of microgravity phenomena and to develop new applications of microgravity. A number of important topics are identified and analyzed in detail. The present article describes results on coating flow, zeolite growth, and rotating electrochemical system.
Results are reported of the Surface Tension Driven Convection Experiment (STDCE) aboard the USML-1 (first United States Microgravity Laboratory) Spacelab which was launched on June 25, 1992. In the experiment 10 cSt silicone oil was placed in an open circular container which was 10 cm wide by 5 cm deep. The fluid was heated either by a cylindrical heater (1.11 cm dia.) located along the container centerline or by a CO2 laser beam to induce thermocapillary flow. The flow field was studied by flow visualization. Several thermistor probes were placed in the fluid to measure the temperature distribution. The temperature distribution along the liquid free surface was measured by an infrared imager. Tests were conducted over a range of heating powers, laser beam diameters, and free surface shapes. In conjunction with the experiments an extensive numerical modeling of the flow was conducted. In this paper some results of the velocity and temperature measurements with flat and curved free surfaces are presented and they are shown to agree well with the numerical predictions.
The role of buoyancy-driven convection in reduced-gravity environments has been emphasized. It is shown that for some materials-processing experiments the values of the fundamental dimensionless parameters such as Gr or Ra are shifted from the very large (ground-based values) to moderately large (space-based values). As a consequence, in cases where approximate analytical solutions are desired, the accuracy of the usual asymptotic (boundary-layer) analysis in which infinitely large parametric ranges are assumed is reduced. Approximate analytical techniques for refinement of the asymptotic solutions are identified that will extend the accuracy to the moderately large parametric ranges associated with space-based processing.
Scaling analysis was used to study thermocapillary flows of low-Prandtl-number fluids in shallow rectangular enclosures under an imposed-heat-flux configuration. Different regimes that appear in the thermo-fluid problem are identified and the proper parameters and reference quantities that define them are obtained. Assuming that the flow is driven by thermocapillary effects and it is concluded that the extent of the region where the thermocapillary driving force is important defines the region of applicability of the scaling results.
The use of thermosolutal and thermocapillary convection in materials processing is experimentally investigated. The flow patterns, unsteady mass transfer, and unsteady temperature variations seen in thermosolutal convection in enclosures are examined. An extensive research program to understand the role of thermocapillary convection in crystal growth for a variety of configurations is reviewed.
Recent research aimed at understanding the transition of thermocapillary flows from steady to oscillatory states is described. Particular attention is given to conditions for the onset of the oscillations and how they are influenced by changes in configuration such as geometry and thermal signature. It is shown that, for high Prandtl number fluids, the oscillations are caused by the coupling among the imposed thermal signature, the surface flow, and the surface deformations. The surface deformations cause a time lag between the surface and bulk-return flows and alter the driving force (surface-temperature gradient).
Thermocapillary flow is driven by a thermally induced surface tension variation along a liquid free surface. In the Earth-gravity environment such flows are usually overshadowed by buoyancy driven flows, but at reduced gravity conditions their influence could be significant. A comprehensive theoretical and experimental research program was stated 12 years ago and is still being continued. Past work done at Case Western Reserve University as well as work done by others is reviewed. The justification for low-gravity experiments is presented.
In considering new directions for low gravity research with particular regard to broadening the number and types of industrial involvements, it is noted that transport phenomena play a vital role in diverse processes in the chemical, pharmaceutical, food, and biotech industries. Relatively little attention has been given to the role of gravity in such processes. Accordingly, numerous industrial processes and phenomena are identified which involve gravity and/or surface tension forces. Phase separations and mixing are examples that will be significantly different in low gravity conditions. A basis is presented for expanding the scope of the low gravity research program and the potential benefits of such research is indicated.
Most analytical studies of ablating layers which melt before they vaporize have been restricted to the stagnation region of bodies (e.g., see Sutton). To determine conditions all along the body, it is important to include the deceleration force that opposes the downstream flow of liquid. Some treatment has already been given to this problem, but it is rather limited because of the idealization of the considered configuration or the omission of some important features of the problem. This note gives a more general discussion of the phenomena that occur when a body force acts on a melting boundary layer. The basis for these remarks is an analysis of the flow of a material like Pyrex over a two-dimensional body. The liquid density, specific heat, and conductivity are assumed constant. To determine the conditions under which deceleration effects are important and to simplify the basic equations, all variables except velocity and time are made dimensionless in the usual way.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.