Engineering Papers⌕ Search

Engineering topics

Ostiguy, Jean-Francois

Publications and source records attributed to Ostiguy, Jean-Francois.

Flattening the field during injection in the Fermilab booster using dipole corrector magnets

The FNAL Booster is a fast cycling 15 Hz resonant circuit synchrotron accelerating proton beam from 400 MeV to 8 GeV. The linac pulse injected into the Booster is ~32 μsec long and fills the ring by multi-turn charge-exchange injection. As part of the PIP-II project, the Booster injection energy and repetition rate will be increased to 800 MeV and 20 Hz respectively. Due to much reduced average current in the new superconducting PIP-II linac, the injection time will increase to 550 μs. A shorter machine cycle coupled to a longer injection time make flattening the injection porch B-field during injection important requirement for successful PIP-II operation. We aim to achieve: (1) flattening of the net bending during injection using dipole correctors, and (2) using a new system based on an Altera FPGA board, reduction of the cycle-to-cycle bending field variation caused by current jitter in the Gradient Magnet Power Supply (GMPS). While the flat injection scheme is essential to future PIP-II operations, it should also noticeably improve efficiency for present HEP operations.

43 PARTICLE ACCELERATORS↗

Full Cycle Simulations of The Fermilab Booster

The Proton Improvement Plan phase II (PIP-II) project currently under construction at FNAL will replace the existing 400 MeV normal conducting linac with a new 800 MeV superconducting linac. The beam power in the downstream rapid-cycling Booster synchrotron will be doubled by raising the machine cycle frequency from 15 to 20 Hz and by increasing the injected beam intensity by a factor 1.5. This has to be accomplished without raising uncontrolled losses beyond the administrative limit of 500 W. In addition, slip-stacking efficiency in the Recycler, the next machine in the accelerator chain, sets an upper limit on the longitudinal emittance of the beam delivered by the Booster. As part of an effort to better understand potential losses and emittance blow-up in the Booster, we have been conducting full cycle 6D simulations using the code PyORBIT. The simulations include space charge, wall impedance effects and transition crossing. In this paper, we discuss our experience with the code and present representative results for possible operational scenarios.

43 PARTICLE ACCELERATORS↗

Space Charge Dominated Momentum Spread and Compensation Strategies in the Post-Linac Section of Proton Improvement Plan-II at Fermilab

The upcoming Proton Improvement Plan-II (PIP-II), designated for enhancements to the Fermilab accelerator complex, features a Beam Transfer Line (BTL) that channels the beam from the linac exit to the booster. In the absence of longitudinal focusing beyond the superconducting linac, the beam experiences an elevated momentum spread, primarily due to nonlinear space-charge forces, surpassing the allowable limit of 2.1e-4. This study presents a detailed examination of the space-charge-induced momentum spread and outlines mitigative strategies. The investigation includes the fine-tuning of a de-buncher cavity, analyzed in terms of operating frequency, longitudinal location, and gap voltage, under both standard and perturbed beam conditions—specifically accounting for momentum jitter and energy variation. The impact of buncher cavity misalignments on the beam's longitudinal phase space is also assessed. The paper concludes by recommending an optimized cavity configuration to effectively mitigate the observed increase in momentum spread along the BTL.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Space Charge Driven Emittance Growth and the Effect of Octupoles in IOTA

The Integrable Optics Test Accelerator (IOTA) at Fermilab is a small machine dedicated to a broad frontier accelerator physics program. An important aspect of this program is to investigate the potential benefits of the resonance free tune spread achievable with integrable optics to store and accelerate high intensity proton beams for which space charge is significant. In this context, a good understanding of proton beam emittance growth and particle loss mechanisms is essential. Assuming nominal design parameters, simulations show that for a bunched beam, the bulk of emittance growth takes place immediately following injection, typically within tens of turns. We attempt to account for this growth using a simplified RMS mismatch theory; some of its limitations and possible improvements are briefly discussed. We then compare theoretical predictions to simulations performed using the PIC code pyORBIT. Further exploring ways to mitigate emittance growth and reduce particle loss, we compare two beam matching strategies: (1) matching at the injection point (2) matching at the center of the nonlinear (octupole) insertion region where $\beta_x = \beta_y$. To observe how nonlinearity affects emittance growth and whether it dominates growth due to mismatch, we track two different distributions. Finally, we explore the potential of using octupoles in a quasi-integrable configuration to mitigate growth using a variety of initial distributions both at reduced and full intensities.

43 PARTICLE ACCELERATORS↗

Modeling Transverse Space Charge effects in IOTA with pyORBIT

The role and mitigation of space charge effects are important aspects of the beam physics research to be performed at the Integrable Optics Test Accelerator (IOTA) at Fermilab. The impact of nonlinear integrability (partial and complete) on space charge driven incoherent and coherent resonances will be a new feature of this accelerator and has the potential to influence the design of future low energy proton synchrotrons. In this report we model transverse space charge effects using the PIC code pyORBIT. First we benchmark the single particle tracking results against MADX with checks on symplecticity, tune footprints, and dynamic aperture in a partially integrable lattice realized with a special octupole string insert. Our space charge calculations begin with an examination of the 4D symplecticity. Short term tracking is done first with the initial bare lattice and then with a matching of the rms values with space charge. Next, we explore slow initialization of charge as a technique to establish steady state and reduce emittance growth and beam loss following injection into a mismatched lattice. We establish values of space charge simulation parameters so as to ensure numerical convergence. Finally, we compare the simulated space charge induced tune shifts and footprints against theory.

43 PARTICLE ACCELERATORS↗

BEAM COLLIMATION IN THE PIP-II LINAC TO BOOSTER TRANSFER LINE

The new PIP-II superconducting linac will deliver a 2 mA average H⁻ beam to the existing Booster synchrotron. The injected beam is accumulated by charge exchange over approximately 300 turns; phase space painting is used to mitigate space charge effects. To limit the power load on the internal waste beam absorber from the transverse tails of the H⁻ distribution missing the foil, the beam will be collimated in both planes in the linac to Booster transfer line using compact collimators of a novel design. Both the number of parasitic hits and the fraction of the beam missing the foil are sensitive functions of the H⁻ beam centroid position with respect to the edge of the foil. The positioning of the collimation is constrained by the availability of suitable space in the transfer line lattice, by specifics of the collimator design, by the phase space orientation at the collimator, and by the betatron phase advance to the foil needed to achieve proper orientation of the spatial distribution at the injection point. In this contribution, we describe the procedure by which collimator positions were optimized. We then discuss the expected performance of the overall system.

Johnson, David E.↗

Validating pyORBIT for Modeling Beam Dynamics in the IOTA Ring

The Integrable Optics Test Accelerator (IOTA) ring is a new Fermilab facility dedicated to beam physics experiments, currently operating with 150 MeV electrons. Space charge effects are expected to be significant when it operates with 2.5 MeV protons. In this contribution, we present results of a suite of validation tests of PyORBIT, a PICstyle space charge code. Single particle dynamics of quasiintegrable optics using an octupole string in IOTA is compared with MADX, and shown to be in good agreement. Requirements for the convergence of space charge computations are systematically established and when possible, tests involving space charge are compared with theoretical predictions.

Li, Runze↗

6D Simulations of PIP-II Booster Injection

The PIP-II superconducting linac will deliver 2 mA average H⁻ beam current at 800 MeV to the existing Booster synchrotron over a period of 0.55 ms (285 turns). As a result, the injected beam power will quadruple to 17 kW. Safe operation at the increased beam power implies careful attention to the origin, magnitude, and distribution of both controlled and uncontrolled losses. Uncontrolled losses are due to neutral ions in excited states stripped in downstream magnets and large angle scattered protons from parasitic foil hits. The relative magnitudes of these loss mechanisms is used to determine the optimal foil thickness. A transverse painting scheme involving closed orbit motion will be used to mitigate space charge effects and minimize parasitic foil hits. Using a detailed full 6D simulation of the injection process, we compute large angle scattering losses and compare results to back of the envelope estimates. We investigate possible impact of space charge on the emittance and beam distribution both during and at the conclusion of the injection period.

43 PARTICLE ACCELERATORS↗

Theory and Conceptual design of kickers

We design dipole and quadrupole striplinekickers to study the effect of echoes in the Integrable Optics Test Accelerator (IOTA) ring. We need to use these kickers to generate an echo:a recoherence of particle motion in phase space. To produce an echo, we use an electromagnetic pulse to kick the beam in a controlled manner. To prevent unwanted reflections and ringing, the characteristic impedance of the kicker should match both the line coming from the pulse generator andsome terminating load(s).

43 PARTICLE ACCELERATORS↗

Modeling Longitudinal Dynamics in the Fermilab Booster Synchrotron

The PIP-II project will replace the existing 400 MeV linac with a new, CW-capable, 800 MeV superconducting one. With respect to current operations, a 50% increase in beam intensity in the rapid cycling Booster synchrotron is expected. Booster batches are combined in the Recycler ring; this process limits the allowed longitudinal emittance of the extracted Booster beam. To suppress eddy currents, the Booster has no beam pipe; magnets are evacuated, exposing the beam to core laminations and this has a substantial impact on the longitudinal impedance. Noticeable longitudinal emittance growth is already observed at transition crossing. Operation at higher intensity will likely necessitate mitigation measures. We describe systematic efforts to construct a predictive model for current operating conditions. A longitudinal only code including a laminated wall impedance model, space charge effects, and feedback loops is developed. Parameter validation is performed using detailed measurements of relevant beam, rf and control parameters. An attempt is made to benchmark the code at operationally favorable machine settings.

43 PARTICLE ACCELERATORS↗

Lattice Design for Project -X CW Superconducting Linac

In this paper, we discuss the beam dynamics optimization of a proposed continuous wave (CW) superconducting linac for Project-X. This 3.0 GeV linac has a peak current of 5-10 mA. The average current is 1 mA, yielding an average beam power of 3 MW. The linac consists of a low energy 325 MHz section (2.5 -470 MeV) containing three families of SC single-spoke resonators, an intermediate energy section (470 MeV-2.0 GeV) containing two families (βg = 0.61 and βg = 0.9) of 650 MHz squeezed SC elliptical cavities and finally, a high energy section (2.0-3.0 GeV) based on 1.3GHz ILC-type (βg = 1.0) cavities. Transverse and longitudinal dynamics in the CW linac are modeled assuming the maximum 1 mA peak current. Different options for transverse focusing are considered.

43 PARTICLE ACCELERATORS↗

The Concept Design of the CW Linac of the Project X

The concept design of the 3 GeV superconducting CW linac of the Project X is discussed. The linac structure and break points for different cavity families are described. The results of the RF system optimization are presented as well as the lattice design and beam dynamics analysis.

43 PARTICLE ACCELERATORS↗

Dynamics of Flat Bunches with Second Harmonic RF

We investigate the dynamics of longitudinally flat bunches created with a second harmonic cavity in a high energy collider. We study Landau damping in a second harmonic cavity with analytical and numerical methods. The latter include particle tracking and evolution of the phase space density. The results are interpreted in the context of possible application to the LHC. A possible path to a luminosity upgrade at the LHC is through the creation of longitudinally flat bunches. They can increase the luminosity roughly by 40% when the beam intensities are at the beam-beam limit. Lower momentum spread which can reduce backgrounds and make collimation easier as well lower peak fields which can mitigate electron cloud effects are other advantages. Use of a second harmonic rf system is a frequently studied method to create such flat bunches. Here we consider some aspects of longitudinal dynamics of these bunches in the LHC at top energy. First we consider intensity limits set by the loss of Landau damping against rigid dipole oscillations. Next we describe numerical simulations using both particle tracking and evolution of the phase space density. These simulations address the consequences of driving a bunch at a frequency that corresponds to the maximum of the synchrotron frequency.

43 PARTICLE ACCELERATORS↗

Remarks on the concept of dispersion in a curved linac

A next-generation linear collider is expected to span tens of kilometers in length. For various reasons, it may be desirable to house such an accelerator in a tunnel that follows the earth's curvature rather that in a 'laser-straight' tunnel. One side effect of opting for a curved linac is the introduction of vertical dispersion. In recent years, much work has been dedicated to understand and evaluate the impact of the presence of dispersion on emittance preservation. While performing simulations with our in-house code (CHEF) we observed a discrepancy between the dispersion function it produces and that computed using other codes in use within the accelerator community. Understanding the origin and the meaning of this discrepancy required a re-examination of the meaning of the concept of dispersion in the context of a linac. The object of this note is to document our findings. We establish that the default dispersion algorithm used by CHEF corresponds to a different, and ultimately more appropriate, definition of the dispersion in presence of acceleration. Not surprisingly, a consistent definition of dispersion restores agreement between codes.

43 PARTICLE ACCELERATORS↗