Engineering Papers⌕ Search

Engineering topics

Orme, Christopher J.

Publications and source records attributed to Orme, Christopher J..

At least 19 records

Thermally reflective membrane apparatuses, and related fluid treatment systems and methods

A thermally reflective membrane apparatus comprises a housing structure, and a thermally reflective membrane contained within the housing structure. The thermally reflective membrane comprises a semipermeable structure, and a porous, thermally reflective structure physically contacting the semipermeable structure. The porous, thermally reflective structure comprises discrete thermally reflective particles, and a binder material coupling the discrete thermally reflective particles to one another and the semipermeable structure. A fluid treatment system and method of treating a fluid are also described.

Klaehn, John R.↗

Rejection of malathion by nanofiltration and reverse osmosis membranes exposed to foulant and two clean-in-place procedures

This research tested the treatment efficacy of an Energy Savings Nanofiltration 1 Low Fouling (ESNA 1-LF) nanofiltration (NF) and an Energy Saving Polyamide 2 (ESPA2) reverse osmosis (RO) membrane for removing malathion from water. Both membranes are of composite polyamide construction. The study included measuring malathion rejection using both pristine membranes and membranes exposed to a simulated secondary wastewater effluent foulant before and after two types of clean-in-place procedures. Across all conditions studied, malathion rejection ranged from 84 to 95% for the ESNA1-LF NF membrane and 77 to 94% for the ESPA2 RO membrane. Contact angle measurements were also collected for each membrane exposure condition. While the contact angle measurements indicated changes to the hydrophobicity of the selective layer of the membranes, they did not correlate to changes in the performance of malathion rejection. As expected, it was observed that malathion rejection improved with the introduction of foulant. Also, the clean-in-place procedures helped restore flux while maintaining malathion rejection.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental study of mechanistic factors influencing solvent-driven fractional crystallization of calcium sulfate

To advance dimethyl ether-driven fractional crystallization (DME-FC), a more sustainable method of water treatment and mineral recovery, a range of chemical equilibria were measured. These include varying concentrations of miscible organic solvents (MOS) used to experimentally measure the solvent-induced solid-liquid equilibrium (SLE) of calcium sulfate (CaSO 4 ) in water. Seven MOS, including dimethyl ether (DME), acetonitrile (MeCN), 1,4-dioxane, tetrahydrofuran (THF), acetone, ethanol, and diethylamine, were screened to establish trends associated with molecular volume, functional groups, and physical properties. The effect of MOS on CaSO 4 removal differed at concentrations <0.15 mol fraction MOS; MOS with greater molecular volume (THF, 1,4-dioxane, and diethylamine) induced greater CaSO 4 precipitation on a per mole basis. The solvent-induced SLE for all MOS converged between 0.15 and 0.2 mol fraction MOS, reaching a CaSO 4 concentration consistent with a water to MOS hydration ratio of 5:1 to 6:1, which may correspond to the solvent generating a solution-based pseudo-clathrate structure with continuity within the solution. Finally, solution pseudo-clathrate structures provide a mechanistic basis for DME-FC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Crosslinked polyphosphazene blends for gas separation membranes

The disclosed invention relates to a composition comprising a crosslinked blend of polyphosphazene polymers. The composition comprises a first polyphosphazene and a second polyphosphazene, where the first polyphosphazene and the second polyphosphazene being bound by a thiol bearing crosslinking agent. Such compositions are useful as a membrane material for the separation of gasses in a gaseous mixture.

Hopkinson, David↗

Molecular dynamics study of carbon dioxide and nitrogen selectivity through poly[bis((methoxyethoxy)ethoxy)phosphazene] (MEEP) membrane

Here, a molecular dynamics simulation model was developed to comprehensively understand carbon dioxide over nitrogen (CO 2 /N 2 ) selectivity through polyphosphazene-based membrane comprising of poly[bis((methoxyethoxy)ethoxy)phosphazene] (MEEP) selective layer at the molecular level. The effects of temperature, pressure, and initial feed gas composition on the CO 2 transport on a polymer membrane were studied. The computed free energy and density profile of the permeating gas mixture exhibited that CO 2 molecules express higher interactions with the membrane than N 2 molecules, resulting in higher CO 2 /N 2 selectivity. Statistical analysis of gas molecules (CO 2 , water (H 2 O), and N 2 ) transportation suggested that hydro- and CO 2 -philic functional groups in the membrane significantly impact CO 2 permeability and CO 2 /N 2 selectivity. This study suggested that Lewis acid–base and hydrogen bonding combinations contribute to CO 2 permeation and CO 2 /N 2 selectivity. An equal CO 2 /N 2 selectivity was observed with and without water vapor in the feed gas suggesting that water does not hinder CO 2 transport through the membrane.

36 MATERIALS SCIENCE↗

Class-based separations of mixed solid–liquid systems with condensable solvent washing and extraction: The dilemma of pizza box recycling

As primary feedstocks deplete across the world, raw material extraction becomes increasingly expensive. Awareness of the environmental impact of primary extraction has motivated the development of energy- and reagent-efficient methods for material reuse. This work confronts an emblematic challenge of modern recycling: the soiled pizza box. While the fibers constituting corrugated cardboard are generally recyclable, pizza contaminants such as sauces and oils complicate their reuse, resulting in municipal prohibitions on the recycling of used pizza boxes in cardboard recycling streams and a representative of 275 kg/year per US household of food waste that is directed to landfill. This challenge is common to many materials, and engineering strategies must be developed to tackle complex/mixed feedstocks. To address the mixed composition of the pizza box (and similar materials), an environmentally benign, non-toxic organic solvent is applied to remove and fractionate components from mixed materials. The solvent employed in this process, dimethyl ether (DME), is a condensable hygroscopic gas, which facilitates its removal and recovery for reuse. Further, the results of this study indicate that 1) DME is capable of solubilizing and extracting components from soiled cardboard and other materials, (resulting in cardboard drier than new/unused cardboard) facilitating its recycling, and 2) the DME-soluble components of the system phase separate into aqueous and fatty acid/oil fractions (potentially ~27.5 kg/year per US household). Condensable solvent-driven washing and extraction enable the efficient separation of multiple intermediate product streams, suggesting a pathway to enable technology development necessary for achieving clean production in a circular economy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Techno-economic analysis of carbon dioxide capture from low concentration sources using membranes

Rising carbon dioxide (CO 2 ) levels in the atmosphere lead to global warming, causing climate change. As such, carbon capture has become necessary to slow the increase and reduce CO 2 levels in the atmosphere. Point source emissions have a wide range of CO 2 concentrations, but emissions below 3% CO 2 have mostly been ignored because Carbon capture from these sources has been viewed as costly and economically unsustainable. Membrane technologies are considered the most viable solution by virtue of more energy-efficient operation. Our group at Idaho National Laboratory (INL) has developed poly[bis((2-methoxyethoxy)ethoxy)phosphazene] (MEEP)-based carbon dioxide selective membranes with CO 2 /N 2 selectivity greater than 40 and CO 2 permeability greater than 450 Barrer. To understand the economics of carbon capture, a spreadsheet-based techno-economic analysis (TEA) model was developed to consider multiple parameters, including selectivity and permeability of the membranes, performance conditions such as the number of stages, module material, electricity price, membrane price, and capital financing. The cost of carbon capture in US $\$$/metric ton was calculated at various purities and compared with other membrane processes, cryogenic capture, solvent-based capture, and pressure swing adsorption-based capture. It was determined that a MEEP-based three-stage process had a capture cost of US $\$$ 50.1/metric ton for 99.8% purity CO 2 from a 1% CO 2 feed source in nitrogen (N 2 ). In conclusion, the capture cost using the best performing Pebax-based membrane was 464% higher, cryogenic capture was 60%–140% higher, pressure swing adsorption was 55%–165% higher, and chemical absorption was -10%–110% higher than MEEP-based membrane capture, respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Root Cause Analysis of Degradation in Protonic Ceramic Electrochemical Cell with Interfacial Electrical Sensors Using Data‐Driven Machine Learning

Abstract Protonic ceramic electrochemical cells (PCECs) offer promising paths for energy storage and conversion. Despite considerable achievements made, PCECs still face challenges such as physiochemical compatibility between componenets and suboptimal solid–solid contact at the interfaces between the electrolytes and electrodes. In this study, a novel approach is proposed that combines in situ electrochemical characterization of interfacial electrical sensor embedded PCECs and machine learning to quantify the contributions of different cell components to total degradation, as well as to predict the remaining useful life. The experimental results suggest that the overpotential induced by the oxygen electrode is 48% less than that of oxygen electrode/electrolyte interfacial contact for up to 1171 h. The data‐driven machine learning simulation predicts the RUL of up to 2132 h. The root cause of degradation is overpotential increase induced by oxygen electrode, which accounts for 82.9% of total cell degradation. The success of the failure diagnostic model is demonstrated by its consistency with degradation modes that do not manifest in electrolysis fade during early real operations. This synergistic approach provides valuable insights into practical failure diagnosis of PCECs and has the potential to revolutionize their development by enabling improved performance prediction and material selection for enhanced durability and efficiency.

25 ENERGY STORAGE↗

Separation of isoprene from biologically-derived gas streams

Renewable organic precursors, including olefinic compounds such as isoprene, have attracted interest from the polymer and pharmaceutical industries. Biologically-derived processes can generate these target compounds; however, their gaseous product streams are complex mixtures of condensable organic vapors (COVs), water vapor, carbon dioxide (CO 2 ), and/or nitrogen (N 2 ). Because COVs, CO 2 and water vapor are known to alter polymer membranes, mixed gas separations data at ambient and elevated temperatures are limited. Here, this study focused on two classes of polymer membranes, glassy [polyetherimide (Ultem®)] and a rubbery [polydimethylsiloxane (PDMS)] with results indicating that isoprene separation is possible in humidified gas environment (2–4 vol% water). Gas permeabilities of these membranes did not noticeably change in the presence of humidity; however, the selectivity of these membranes was significantly lower compared to their performance under dry conditions. The role of water vapor in gas transport was derived from the energy of activation of permeation (E p ) for PDMS and Ultem® from 30–80°C in humidified mixed gas streams. For both polymers, E p data shows a slight decrease in selectivity with the other gases (hydrogen, N 2 , CO 2 , and methane) at elevated temperatures in the presence of water vapor. Thus, these COVs separations are feasible with polymer membranes in the presence of humidified gas streams, even in the case of glassy and rubbery membranes in series.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Methods and systems for treating an aqueous solution

A method of treating an aqueous solution comprises forming a treatment stream comprising a condensable material. The treatment stream is introduced to an aqueous solution comprising water and a solute to fractionally precipitate the solute out of the aqueous solution and form a solids stream comprising the solute and an aqueous liquid stream comprising at least one solute-depleted solution of the water and the condensable material. The condensable material of at least a portion of the aqueous liquid stream is separated from the water of the at least a portion of the aqueous liquid stream to at least partially reform the treatment stream and form an aqueous liquid product stream depleted in the solute. Aqueous solution treatment systems and additional methods of treating an aqueous solution are also described.

Wilson, Aaron D.↗

Electrochemically Engineered, Highly Energy-Efficient Conversion of Ethane to Ethylene and Hydrogen below 550 °C in a Protonic Ceramic Electrochemical Cell

Ethylene is one of the largest building blocks in the petrochemical industry, mainly produced by steam cracking of ethane derived from naphtha or shale gas at high temperatures (>800 °C). Despite its technical maturity and economic competitiveness, the thermal steam cracking of ethane is highly energy-intensive. In this work, an electrochemically engineered direct conversion process of ethane to produce hydrogen and ethylene using a planar protonic ceramic membrane reactor with a bi-functional three-dimensional catalytic electrode is reported, with a single-pass ethane conversion of 40% and ethylene yield of 26.7% at 550 °C. Compared with the industrial ethane steam cracking, this method saves process energy input by 45.1% and improves process energy efficiency by 50.6%, based on comprehensive process simulation using Aspen Plus software. Further, steam electrolysis treatment under the solid oxide electrolysis cell mode can regenerate the system’s catalytic performance and significantly alleviate catalytic degradation by 74%, demonstrating high techno-economic viability.

bi-functional electrode↗

Self-sustainable protonic ceramic electrochemical cells using a triple conducting electrode for hydrogen and power production

The protonic ceramic electrochemical cell (PCEC) is an emerging and attractive technology that converts energy between power and hydrogen using solid oxide proton conductors at intermediate temperatures. To achieve efficient electrochemical hydrogen and power production with stable operation, highly robust and durable electrodes are urgently desired to facilitate water oxidation and oxygen reduction reactions, which are the critical steps for both electrolysis and fuel cell operation, especially at reduced temperatures. In this study, a triple conducting oxide of PrNi 0.5 Co 0.5 O 3-δ perovskite is developed as an oxygen electrode, presenting superior electrochemical performance at 400-600°C. More importantly, the self-sustainable and reversible operation is successfully demonstrated by converting the generated hydrogen in electrolysis mode to electricity without any hydrogen addition. The excellent electrocatalytic activity is attributed to the considerable proton conduction, as confirmed by hydrogen permeation experiment, remarkable hydration behavior and computations.

08 HYDROGEN↗

Dual 3D Ceramic Textile Electrodes: Fast Kinetics for Carbon Oxidation Reaction and Oxygen Reduction Reaction in Direct Carbon Fuel Cells at Reduced Temperatures

Abstract Direct carbon fuel cells (DCFCs) are an efficient energy‐conversion technology capable of generating electricity with carbon‐dioxide‐capture chemistry with solid carbon as fuels. The efficiency and performance of DCFCs depend on the kinetics of the carbon oxidation reactions (COR) and the oxygen reduction reactions (ORR), each occurring at anode and cathode, respectively. The limited active sites paired with reduced temperatures greatly decrease the efficiency of the electrochemical reactions. Ultraporous dual‐3D ceramic textiles (dual‐3DCT) are integrated into electrolyte‐supported DCFCs to enhance charge and mass transfer at the electrodes. Improved COR at the anode is achieved by the synergy between the 3DCT NiO–Ce 0.8 Gd 0.2 O 1.95 (GDC) structure and optimal carbon fuel choice. In a comparative study, DCFCs using graphitic carbon (GC) as fuel show the best COR performance when compared to DCFCs utilizing alternative fuels such as carbon black (CB) and activated carbon (AC). The 3DCT Sm 0.5 Sr 0.5 CoO 3‐δ –GDC (SSC–GDC) composite cathode shows electrochemical performance superior to that of the conventional screen‐printed SSC–GDC. A peak power density of 392 mW cm −2 at 600 °C is obtained in a DCFC using the 3DCT‐anode/electrolyte/3DCT‐cathode configuration, an unprecedented value for any reported DCFC as of yet. This points toward promising applications of dual‐3DCT electrodes for reduced‐temperature DCFCs.

Bian, Wenjuan↗