Engineering Papers⌕ Search

Engineering topics

Oren, J. A.

Publications and source records attributed to Oren, J. A..

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

High-Capacity Heat-Pipe Evaporator

Heat pipe with cylindrical heat-input surface has higher contact thermal conductance than one with usual flat surface. Cylindrical heat absorber promotes nearly uniform flow of heat into pipe at all places around periphery of pipe, helps eliminate hotspots on heat source. Lugs in aluminum pipe carry heat from outer surface to liquid oozing from capillaries of wick. Liquid absorbs heat, evaporates, and passes out of evaporator through interlug passages.

Oren, J. A.↗
NASA NTRS1988

Condensing, Two-Phase, Contact Heat Exchanger

Two-phase heat exchanger continuously separates liquid and vapor phases of working fluid and positions liquid phase for efficient heat transfer. Designed for zero gravity. Principle is adapted to other phase-separation applications; for example, in thermodynamic cycles for solar-energy conversion.

Cox, R. L.↗
NASA NTRS1988

Space erectable radiator system development

The NASA Space Station's Space Erectable Radiator System features modular radiator panels with high-capacity tapered artery heat pipes bonded within their aluminum honeycomb structures. Simple, dry aluminum-to-aluminum thermal contact surfaces are used for the connections, thereby requiring no fluid joints; a uniformly distributed clamping force at the radiator panel-to-thermal transport loop interface heat exchange surface yields high thermal contact conductance as well as minimum area and weight for the requisite performance. The design has been optimized for weight and cost.

Oren, J. A.↗
NASA NTRS1985

Challenges in the development of the orbiter radiator system

Major technical challenges which were met in the design and development of the Space Shuttle Orbiter Radiator System are discussed. This system rejects up to 30 kW of waste heat from eight individual radiators having a combined surface area of 175 sq m. The radiators, which are deployable, are mounted on the inside of the payload bay doors for protection from aerodynamic heating during ascent and re-entry. While in orbit the payload bay doors are opened to expose the radiators for operation. An R21 coolant loop accumulates waste heat from various components in the Orbiter and delivers the heat to the radiators for rejection to space. Specific challenges included high acoustically induced loads during lift-off, severe radiating area constraints, demanding heat load control requirements, and long life goals. Details of major design and analysis efforts are discussed. The success of the developed hardware in satisfying mission objectives showed how well the design challenge was met.

Williams, J. L.↗
NASA NTRS1982

Flexible radiator system

The soft tube radiator subsystem is described including applicable system requirements, the design and limitations of the subsystem components, and the panel manufacturing method. The soft tube radiator subsystem is applicable to payloads requiring 1 to 12 kW of heat rejection for orbital lifetimes per mission of 30 days or less. The flexible radiator stowage volume required is about 60% and the system weight is about 40% of an equivalent heat rejection rigid panel. The cost should also be considerably less. The flexible radiator is particularly suited to shuttle orbiter sortie payloads and also whose mission lengths do not exceed the 30 day design life.

Oren, J. A.↗
NASA NTRS1982

Flexible radiator thermal vacuum test report

Two flexible, deployable/retraction radiators were designed and fabricated. The two radiator panels are distinguishable by their mission life design. One panel is designed with a 90 percent probability of withstanding the micrometeoroid environment of a low earth orbit for 30 days. This panel is designated the soft tube radiator after the PFA Teflon tubes which distribute the transport fluid over the panel. The second panel is designed with armored flow tubes to withstand the same micrometeoroid environment for 5 years. It is designated the hard tube radiator after its stainless steel flow tubes. The thermal performance of the radiators was tested under anticipated environmental conditions. The two deployment systems of the radiators were evaluated in a thermal vacuum environment.

Oren, J. A.↗
NASA NTRS1982

Thermal management for large space platforms

This paper provides an evaluation of heat rejection techniques applicable to multihundred-kilowatt space platforms. A number of promising heat rejection concepts were parametrically weight-optimized over a wide range of conditions to provide a 99% reliability of achieving a 10-yr life for the multihundred-kilowatt space platform. Three panel designs were considered: (1) an advanced meteoroid-bumpered hybrid heat pipe concept, (2) a bumpered liquid concept, and (3) a space constructable heat pipe radiator. The following are some of the significant findings from the study: (1) A single subsystem approach can be used with the heat pipe system, whereas several smaller subsystems are required for the pumped fluid systems. (2) The space constructable radiator approach offers a 10% weight reduction and operational advantages over the conventionally deployed panels.

Oren, J. A.↗
NASA NTRS1981

Study of thermal management for space platform applications: Unmanned modular thermal management and radiator technologies

Candidate techniques for thermal management of unmanned modules docked to a large 250 kW platform were evaluated. Both automatically deployed and space constructed radiator systems were studied to identify characteristics and potential problems. Radiator coating requirements and current state-of-the-art were identified. An assessment of the technology needs was made and advancements were recommended.

Oren, J. A.↗
NASA NTRS1980

Study of thermal management for space platform applications

Techniques for the management of the thermal energy of large space platforms using many hundreds of kilowatts over a 10 year life span were evaluated. Concepts for heat rejection, heat transport within the vehicle, and interfacing were analyzed and compared. The heat rejection systems were parametrically weight optimized over conditions for heat pipe and pumped fluid approaches. Two approaches to achieve reliability were compared for: performance, weight, volume, projected area, reliability, cost, and operational characteristics. Technology needs are assessed and technology advancement recommendations are made.

Oren, J. A.↗
NASA NTRS1975

Cooling systems for satellite remote sensing instrumentation

The current and developing state-of-the-art in cryogenic coolers for satellite sensors was studied for earth oriented satellites. Six representative sensor categories in the 77 K to 300 K range were defined. Cooling capacities were 50 to 1000 mw; both continuous and intermittent duty cycles were considered; lifetimes were one to two years. Conceptual designs were prepared for the most promising coolers in each category. These coolers are Joule-Thomson, Solid Cryogen, Vuilleumier, Thermoelectric, Shielded Radiator, Optical Solar Reflector Radiator and Unshielded Radiator. Weight, envelope, power requirements and operating characteristics of each cooler are described. Scaling data for each cooler are included.

Copeland, R. J.↗
NASA NTRS1975

SINDA/SINFLO computer routine, volume 1, revision A

The SINFLO package was developed to modify the SINDA preprocessor to accept and store the input data for fluid flow systems analysis and adding the FLOSOL user subroutine to perform the flow solution. This reduced and simplified the user input required for analysis of flow problems. A temperature calculation method, the flow-hybrid method which was developed in previous VSD thermal simulator routines, was incorporated for calculating fluid temperatures. The calculation method accuracy was improved by using fluid enthalpy rather than specific heat for the convective term of the fluid temperature equation. Subroutines and data input requirements are described along with user subroutines, flow data storage, and usage of the plot program.

Oren, J. A.↗
NASA NTRS1974

Cooling systems for satellite remote sensing instrumentation

The characteristics of a cryogenic cooling system for the Pollution Monitoring Satellite (PMS) are discussed. Studies were conducted to make the following determinations: (1) the characteristics and use of proven and state-of-the-art cryogenic cooling systems for six specified ranges of performance, (2) the system most applicable for each of the six cooling categories, and (3) conceptual designs for candidate system for each of the six representative cooling categories. The six cooling categories of electrical loads are defined. The desired mission life for the cooling system is two years with both continuous and intermittent operating conditions.

Copeland, R. J.↗
NASA NTRS1973

Thermal and flow analysis subroutines for the SINDA-version 9 computer routine

Fluid flow analysis, special thermal analysis and input/output capabilities of the MOTAR routine were incorporated into the SINDA routine. All the capabilities were added in the form of user subroutines so that they may be added to different versions of SINDA with a minimum of programmer effort. Two modifications were made to the existing subroutines of SINDA/8 to incorporate the above subroutines. These were: (1) A modification to the preprocessor to permit actual values of array numbers, conductor numbers, node numbers or constant numbers supplied as array data to be converted to relative numbers. (2) Modifications to execution subroutine CNFAST to make it compatible with the radiant interchange user subroutine, RADIR. This modified version of SINDA has been designated SINDA/version 9. A detailed discussion of the methods used for the capabilities added is presented. The modifications for the SINDA subroutines are described, as well as user subroutines. All subroutines added or modified are listed.

Oren, J. A.↗
NASA NTRS1972

Modular thermal analyzer routine, volume 1

The Modular Thermal Analyzer Routine (MOTAR) is a general thermal analysis routine with strong capabilities for performing thermal analysis of systems containing flowing fluids, fluid system controls (valves, heat exchangers, etc.), life support systems, and thermal radiation situations. Its modular organization permits the analysis of a very wide range of thermal problems for simple problems containing a few conduction nodes to those containing complicated flow and radiation analysis with each problem type being analyzed with peak computational efficiency and maximum ease of use. The organization and programming methods applied to MOTAR achieved a high degree of computer utilization efficiency in terms of computer execution time and storage space required for a given problem. The computer time required to perform a given problem on MOTAR is approximately 40 to 50 percent that required for the currently existing widely used routines. The computer storage requirement for MOTAR is approximately 25 percent more than the most commonly used routines for the most simple problems but the data storage techniques for the more complicated options should save a considerable amount of space.

Oren, J. A.↗
NASA NTRS1971

Radiator design system computer programs

Minimum weight space radiator subsystems which can operate over heat load ranges wider than the capabilities of current subsystems are investigated according to projected trends of future long duration space vehicles. Special consideration is given to maximum heat rejection requirements of the low temperature radiators needed for environmental control systems. The set of radiator design programs that have resulted from this investigation are presented in order to provide the analyst with a capability to generate optimum weight radiator panels or sets of panels from practical design considerations, including transient performance. Modifications are also provided for existing programs to improve capability and user convenience.

Wiggins, C. L.↗