Engineering PapersSearch

Engineering topics

Ono, M.

Publications and source records attributed to Ono, M..

Recent progress in the development of liquid metal plasma facing components for magnetic fusion devices

One of the most critical challenges for future fusion reactors is to develop longevity plasma-facing components (PFCs) exposed to extremely high heat and neutron loads. As opposed to those employing solid metals, PFCs with flowing liquid metals (LM) have shown self-healing, heat removal and good impurity control capabilities, all essential to fusion devices. Recently, significant progress in LM-PFC development has been reported globally, with data from several magnetic fusion devices. These studies reveal that LM-PFCs can endure extreme heat fluxes while maintaining plasma compatibility. New design concepts have been proposed and numerically analyzed, advancing models for liquid PFCs in future reactors. Despite existing technical challenges, these developments suggest that LM-PFCs hold promise for future fusion applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY

Full-wave simulations on helicon and parasitic excitation of slow waves near the edge plasma

Helicon waves are thought to be promising in various tokamaks, such as DIII-D, because they can penetrate reactor-grade high-density cores and drive the off-axis current with higher efficiency. In the frequency regime ~476 MHz, both slow electrostatic and fast electromagnetic helicon waves can coexist in DIII-D. If the antenna parasitically excites the slow mode, these waves can propagate along the magnetic field line into the scrape-off layer (SOL). Although the importance of the misalignment of the Faraday screen and the electron density in the SOL on the excitation and propagation of slow modes is well known, the conditions for minimizing slow mode excitation have yet to be optimized. Using the Petra-M simulation code in the 2D domain, we analyze the effects of the misalignment of the antenna in the poloidal direction, the misalignment of the Faraday screen in the toroidal direction, and the density in front of the antenna on slow mode generation. Our results suggest that the misalignment of the Faraday screen is a critical factor in reducing the slow mode and that the misalignment angle should be below ~5° to minimize the slow wave excitation. When the electron density is higher than 3.5 x 10 18 m –3 in the SOL, the generation of the slow mode from the antenna is minimized and unaffected by the misalignment of the Faraday screen.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY

X-ray sources for in situ wavelength calibration of x-ray imaging crystal spectrometers

X-ray sources for a range of wavelengths are being considered for in situ calibration of X-ray Imaging Crystal Spectrometers (XICSs) and for monitoring line shifts due to changes in the crystal temperature, which can vary during experimental operation over a day [A. Ince-Cushman et al., Rev. Sci. Instrum. 79, 10E302 (2008), L. Delgado-Aparicio et al., Plasma Phys. Control. Fusion 55, 125011 (2013)]. Such crystal temperature dependent shifts, if not accounted for, could be erroneously interpreted as Doppler shifts leading to errors in plasma flow-velocity measurements. The x-ray sources encompass characteristic x-ray lines falling within the wavelength range of 0.9–4.0 Å, relevant for the XICSs on present and future fusion devices. Several technological challenges associated with the development of x-ray sources for in situ calibration are identified and are being addressed in the design of multiple x-ray tubes, which will be installed inside the spectrometer housing of the XICS for the JT-60SA tokamak. These x-ray sources will be especially useful for in situ calibration between plasma discharges. Here, in this paper, laboratory experiments are described that were conducted with a Cu x-ray source, a heated quartz (102) crystal, and a pixelated Pilatus detector to measure the temperature dependent shifts of the Cu Kα 1 and Kα 2 lines at 1.5405 and 1.5443 Å, respectively, and to evaluate the 2d-lattice constant for the Bragg reflecting crystal planes as a function of temperature, which, in the case of in situ wavelength calibration, would have to be used for numerical analysis of the x-ray spectra from the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY

Lunar Rover Localization Using Craters as Landmarks

Onboard localization capabilities for planetary rovers to date have used relative navigation, by integrating combinations of wheel odometry, visual odometry, and inertial measurements during each drive to track position relative to the start of each drive. At the end of each drive, a “ground-in-the-loop” (GITL) interaction is used to get a position update from human operators in a more global reference frame, such as a map frame defined by orbital reconnaissance imaging of a large region around the rover’s current position. For Mars rovers, this typically has involved downlinking imagery from the rover mast cameras and using interactive visualization tools on Earth to register such images to the orbital reconnaissance images. For safety purposes, rover mission operations typically specify “keep out zones”, which human operators recognize as being unsafe in the orbital images. Autonomous rover drives are limited in distance so that accumulated relative navigation error does not risk the possibility of the rover driving into a keep out zone. The allowable autonomous drive distance in this mode of operation depends on the distribution of keep out zones and the accuracy of relative navigation; in practice, drive limits of a few hundred meters between GITL cycles are to be expected. Several rover mission concepts have recently been studied that require much longer drives between GITL cycles, particularly for the Moon. This includes lunar rover mission concepts that involve (1) driving mostly in sunlight at low latitudes, (2) driving in permanently shadowed regions near the south pole, and (3) a mixture of day and night driving in mid-latitudes. These concepts include total traverse distance requirements of up to 1,800 km in 4 Earth years, with individual drives of several kilometers between stops for downlink. These concepts require greater autonomy to minimize GITL cycles to enable such large range; onboard global localization is a key element of such autonomy. Multiple techniques have been studied in the past for onboard rover global localization, including radio navigation aiding from an orbiter, recognizing horizon landmarks that are known in a regional elevation map, and correlating a local elevation map created onboard the rover with a regional elevation map. These techniques all have drawbacks, including requiring an expensive extra mission element (navigation orbiter), unavailability of sufficient regional elevation map data, or limited accuracy in resulting position estimates (e.g. a few hundred meters with horizon landmarks). For the Moon, the ubiquitous craters offer another possibility, which involves mapping craters from orbit, then recognizing crater landmarks with cameras and/or a lidar onboard the rover. This approach is applicable everywhere on the Moon, does not require high resolution stereo imaging from orbit as some other approaches do, and has potential to enable position knowledge with order of 10 m accuracy at all times. This paper will provide more detail on our technical approach to crater-based lunar rover localization and will present initial results on crater detection using 3-D point cloud data from onboard lidar or stereo cameras and using shading cues in monocular onboard imagery.

Ono, M.

New Rover Conops with High-Performance Onboard Computing: Give Up Raw Data to Reduce Ops Cost and Do More Science

A major portion of time during the tactical operation of Mars rovers is spent for selecting, prioritizing, and coordinating sciences and engineering activities such that they fit within resource constraints, including the downlink data volume, energy, and time. In particular, the downlink data volume constraint is getting particularly tighter in recent missions because modern instruments produce increasingly high data volume while the communication bandwidth is essentially bounded by the law of physics. Tactical operation would be substantially simplified, hence the operation cost could be reduced, if the data volume constraint is relaxed or even removed. In this abstract, we propose a new operation paradigm for achieving this goal. The key observation is that, both in science and engineering applications, the bit size of raw data is typically much greater than the volume of processed information that is needed for scientific or engineering analysis. For example, a full-resolution image from Mastcam-Z, the main science camera on Perseverance, is about 700 kB in volume and we downlinked 29,685 images up to Sol 243, totaling ~20 GB of data. But of course, scientists do not use every pixel of these images; what they really look for in the images are geological features, typically represented by specific geometric configurations or textures. An end product after processing hundreds of Mascam-Z images could be a single geological map summarizing the spatial distribution of the features. For another example, a 100-meter drive of Perseverance produces 7-12 MB of drive telemetry, which records every detail of the rover's motion at 8 Hz, including position, attitude, steering angles, encoder readings, motor currents and many other information. But what the ground engineers eventually pay attention to is the signs of anomaly, such as excessive motor currents or high slip; if a drive is nominal, the vast majority of this data is unused. What if, then, we process the raw data onboard and only downlink the processed data that is relevant to scientific or engineering analyses, such as a list of detected science features (with cropped images) or a list of potential signs of anomaly while driving? A major roadblock for such onboard, high-level information processing has been the onboard computational resource. RAD750, the main onboard computer of Perseverance, is obviously not sufficient for performing complex image or signal processing such as object detection, semantic segmentation, or anomaly detection. Interestingly, RAD750 is not the best processor that Perseverance has; Qualcomm's Snapdragon 801, a modern mobile processor, is on her Heli Base Station, a device for communicating with Mars Helicopter Ingenuity; also, Intel's Atom E3845 processors are on engineering cameras. In the reminder of this paper, we will introduce two particular uses cases of these high-performance co-processors (meaning auxiliary CPU, GPU, or other types of processors that are separate from the main processor that runs the main flight software) for lowering operation cost and accommodating more science activities for a given communication constraint.

Didier, A.

Experiment of static and dynamic characteristics of spiral grooved seals

The leakages and the dynamic characteristics of six types of spiral grooved seals are experimentally investigated. The effect of the helix angle of the seal is investigated mainly under the condition of the same nominal clearances, land and groove lengths, and groove depths. The dynamic characteristics are measured for various parameters such as preswirl velocity, pressure difference between inlet and outlet of the seal, whirling amplitude, whirling speed, and rotating speed of the rotor. The results are also compared with leakage increases with the increase of the helix angle, but as the rotating speed increases, the leakages of the larger helix angle seals quickly drop. The leakage of the smooth-stator (SS)/smooth-grooved rotor (SGR) seal drops faster than that of the spiral-grooved stator (SGS)/smooth-rotor (SR) seal. It is found that a circumferential flow can be produced by the flow along the helix angle direction, and this circumferential flow acts as a negative swirl. For the present helix angle range, there is an optimum helix angle with which the seal has a comparatively positive effect on the rotor stability. Compared with the SGS/SR seals, the SS/SGR seal has a worse effect on the rotor stability.

Iwatsubo, T.

Detection of surface glow related to spacecraft glow phenomena

A source of low energy neutral atoms and molecules has been developed by using a biased limiter to scrape off and reflect neutralized ions from a toroidal plasma. Beams of nitrogen and nitrogen-oxygen mixtures with energies of 1 to 15 eV and fluxes greater than about 10 to the 14 per centimeter per second were directed onto target surfaces consisting of Z-302 and Z-306 paints. With the nitrogen beams, a glow due to beam-surface interactions was successfully detected. In addition, a volume glow effect due to beam-gas interactions was observed which may play a role in spacecraft glow.

Langer, W. D.

A ground-based experimental test program to duplicate and study the spacecraft glow phenomenon

The use of a plasma device, the Advanced Concepts Torus-I, for producing atoms and molecules to study spacecraft glow mechanisms is discussed. A biased metal plate, located in the plasma edge, is used to accelerate and neutralize plasma ions, thus generating a neutral beam with a flux approx. 5 x 10 to the 14th power/sq cm/sec at the end of a drift tube. Our initial experiments are to produce a 10 eV molecular and atomic nitrogen beam directed onto material targets. Photon emission in the spectral range 2000 to 9000 A from excited species formed on the target surface will be investigated.

Langer, W. D.