Engineering Papers⌕ Search

Engineering topics

Olson, David

Publications and source records attributed to Olson, David.

Route selection based on buffer congestion

A switch includes a plurality of ingress ports, a plurality of egress ports, and a plurality of buffers comprising a buffer coupled to each ingress port, egress port pair. An ingress port is to determine a plurality of potential egress ports for a packet. The ingress port is to select an egress port of the plurality of potential egress ports based on congestion of the corresponding buffers coupled to the ingress port and to each of the plurality of potential egress ports. The ingress port is to place the packet into the corresponding buffer coupled to the ingress port and the selected egress port.

Olson, David↗

Development of a numerical model for simulating stress corrosion cracking in spent nuclear fuel canisters

Abstract Prediction and detection of the chloride-induced stress corrosion cracking (CISCC) in Type 304 stainless steel spent nuclear fuel canisters are vital for the lifetime extension of dry storage canisters. This paper conducts a critical review that focuses on the numerical modeling and simulation on the research progress of the CISCC. The numerical models emphasizing the residual stress, susceptible microstructure, and corrosive environment are summarized individually. Meanwhile, the simulation studies on the role of hydrogen-assisted cracking are reviewed. Finally, a multi-physical numerical model, which combines the different fields is proposed based on our recent investigation.

Materials Science↗

Molecular tail chemistry controls thermal transport in fullerene films

Herein we report on the thermal conductivities of alkyl- and indene-group functionalized fullerene derivative thin films as measured via time domain thermoreflectance and steady state thermoreflectance. The thermal conductivities vary from 0.064 ± 0.007 W m – 1 K – 1 for [6,6]-phenyl C 61 -butyric acid methyl ester (PCBM) to 0.15 ± 0.017 W m – 1 K – 1 for indene- C 60 bisadduct at room temperature and do not exhibit significant temperature dependence from 300 to 375 K. In comparison to the thermal conductivity of PCBM, increasing the length of the alkyl chain, as in the case of [6,6]-phenyl C 61 -butyric acid butyl ester, and [6,6]-phenyl C 61 -butyric acid octyl ester leads to higher thermal conductivities. Likewise, increasing the number of alkyl chains attached to the fullerenes as in the case of bisadduct PCBM leads to a higher thermal conductivity compared to that of PCBM. We present atomistic insights into the role of chemical functionalization on the overall heat transfer in these fullerene derivatives by conducting molecular dynamics simulations and lattice dynamics calculations. The thermal conductivities predicted via our atomistic simulations qualitatively agree with the experimental trends for our fullerene derivatives. Lattice dynamics calculations reveal that one of the main factors dictating the ultralow thermal conductivities in fullerene derivatives is the large reduction in modal diffusivities in the molecular crystals as calculated from the Allen-Feldman model, thus providing an explanation for their largely reduced thermal conductivities as compared to that of C 60 crystals. The low diffusivities result from high degrees of localization of Einstein-like vibrations in fullerene derivatives due to the molecular side chains, providing the ability to dial-in the properties of these low thermal conductivity solids via molecular engineering.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Radiation Damage Studies of Materials and Electronic Devices Using Hadrons

We have irradiated NdFeB permanent magnet samples from different manufacturers and with differing values of coercivity and remanence using stepped doses of 1 MeV equivalent neutrons up to a fluence of 0:64 1015n=cm2 to evaluate effects on magnetization and B field distributions. The samples with high coercivity, irradiated in open circuit configurations, showed no or minimal effects when compared with unirradiated samples, whereas the lower coercivity magnets suffered significant losses of magnetization and changes in the shapes of their field patterns. One such magnet underwent a fractional magnetization loss of 13.1% after a fluence of 0:59 1015 n=cm2. This demagnetization was not uniform. With increasing fluence, B field scans along the centerlines of the pole faces revealed that the normal component of B decreased more near the midpoint of the scan than near the ends. In addition, a fit to the curve of overall magnetization loss with fluence showed a significant deviation from linearity. The results are discussed in light of other measurements and theory. The high coercivity materials appear suitable for use in accelerator applications subject to irradiation by fast neutrons such as dipoles where the internal demagnetizing field is comparable to or less than that of the open circuit samples tested in this study.

Pellett, David↗

Development and Characterization of Improved NiTiPd High-Temperature Shape-Memory Alloys by Solid-Solution Strengthening and Thermomechanical Processing

The need for compact, solid-state actuation systems for use in the aerospace, automotive, and other transportation industries is currently motivating research in high-temperature shape-memory alloys (HTSMA) with transformation temperatures greater than 100 C. One of the basic high-temperature alloys investigated to fill this need is Ni(19.5)Ti(50.5)Pd30. Initial testing has indicated that this alloy, while having acceptable work characteristics, suffers from significant permanent deformation (or ratcheting) during thermal cycling under load. In an effort to overcome this deficiency, various solid-solution alloying and thermomechanical processing schemes were investigated. Solid-solution strengthening was achieved by substituting 5at% gold or platinum for palladium in Ni(19.5)Ti(50.5)Pd30, the so-called baseline alloy, to strengthen the martensite and austenite phases against slip processes and improve thermomechanical behavior. Tensile properties, work behavior, and dimensional stability during repeated thermal cycling under load for the ternary and quaternary alloys were compared. The relative difference in yield strength between the martensite and austenite phases and the dimensional stability of the alloy were improved by the quaternary additions, while work output was only minimally impacted. The three alloys were also thermomechanically processed by cycling repeatedly through the transformation range under a constant stress. This so-called training process dramatically improved the dimensional stability in these samples and also recovered the slight decrease in work output caused by quaternary alloying. An added benefit of the solid-solution strengthening was maintenance of enhanced dimensional stability of the trained material to higher temperatures compared to the baseline alloy, providing a greater measure of over-temperature capability.

Bigelow, Glen↗