Engineering topics

Okasinski, John S.

Publications and source records attributed to Okasinski, John S..

12 records

DOE OSTI2024

Operando Investigation on the Role of Densification and Chemo-Mechanics on Solid-State Cathodes

All solid-state batteries are desirable for a range of energy storage applications which require high energy density. Achieving a high energy density in a solid-state battery requires the operation of an energy dense anode with a composite solid-state cathode. Pores and/or voids within a solid state cathode are ion-blocking and thus control over the concentration and distribution of pores in the initial electrode and cycled electrode is desirable. This study provides an understanding of the interplay between electrode microstructure and mechanics on active material utilization in solid state cathodes composed of NCM 811 and Li 6 PS 5 Cl. Decreasing the solid electrolyte particle size leads to greater active material-electrolyte contact and less total deformation when exposed to an external load. Composite cathodes with greater compliance can potentially decrease strain between the active material and solid electrolyte, decrease delamination events and result in higher overall active material utilization and high capacity retention.

25 ENERGY STORAGE↗

DOE OSTI2023

Li-ion and Na-ion intercalation in layered MnO 2 cathodes enabled by using bismuth as a cation pillar

Low-cost batteries based on Earth-abundant materials are needed for large-scale electrical storage for the grid. Cathodes based almost entirely on Mn oxides would reduce overall battery cost but cycling of Mn oxides is often not stable. In Li-ion cells, most polymorphs of MnO 2 undergo irreversible transformation to spinel LiMn 2 O 4 during cycling, causing capacity loss. Doping MnO 2 with Bi is known to stabilize the structure, but previous reports have relied on low-crystallinity material making it impossible to pinpoint the Bi location in the structure or its mechanism. In this work, we report a series of hydrated Bi-doped layered MnO 2 compounds and characterize their structures as a function of Bi amount. Bi is shown to reside in the material interlayer, provoking higher long-range structural order even at a low doping level of 1.3%. Doped material improves the specific capacity and stability of cycling in both Li-ion and Na-ion cells. A high level of Bi doping, 4.3%, causes loss of the interlayer crystal water in non-aqueous electrolyte, and this reduces the interlayer distance. Crystal water is shown to be beneficial in a Na-ion system, while its loss improves Li-ion cycling. This provides fundamental insight into how pillaring by a heavy, multivalent cation stabilizes layered oxides.

25 ENERGY STORAGE↗

DOE OSTI2023

Lithiation Gradients and Tortuosity Factors in Thick NMC111-Argyrodite Solid-State Cathodes

Achieving high energy density in all-solid-state lithium batteries will require the design of thick cathodes, and these will need to operate reversibly under normal use conditions. We use high-energy depth-profiling X-ray diffraction to measure the localized lithium content of Li 1-x Ni 1/3 Mn 1/3 Co 1/3 O 2 (NMC111) through the thickness of 110 μm thick composite cathodes. The composite cathodes consisted of NMC111 of varying mass loadings mixed with argyrodite solid electrolyte Li 6 PS 5 Cl (LPSC). During cycling at C/10, substantial lithiation gradients developed, and varying the NMC111 loading altered the nature of these gradients. Microstructural analysis and cathode modeling showed this was due to high tortuosities in the cathodes. This was particularly true in the solid electrolyte phase, which experienced a marked increase in tortuosity factor during the initial charge. Our results demonstrate that current distributions are observed in sulfide-based composites and that these will be an important consideration for practical design of all-solid-state batteries.

25 ENERGY STORAGE↗

DOE OSTI2022

Discharge intermittency considerably changes ZnO spatial distribution in porous Zn anodes

Porous Zn anodes are ubiquitous in primary batteries and are under development for low-cost rechargeable batteries. Spatial distribution of ZnO discharge product is a critical factor in these, because it can passivate the active material. In rechargeable cells this is related to a major failure mechanism called shape change, in which ZnO is relocated to inactive locations. In this work we demonstrate rest steps during discharge of primary Zn anodes dramatically alter the placement of ZnO in the anode. In alkaline electrolyte, ZnO discharge product is typically modeled as precipitating close to Zn particles, forming a porous ZnO shell around the Zn core. Further, anodes discharged continuously at low-rate are compared to anodes similarly discharged intermittently, using in situ computed tomography from a synchrotron source. Zn–ZnO core-shell structures are produced during continuous discharge but are not found in cells discharged intermittently. Continuously discharged cells showed that ZnO was formed most strongly near the separator, in agreement with Zn anode battery models. In pulse-discharged cells, ZnO was more radially distributed and was in large formations not physically connected to Zn particles. Thus, discharge intermittency changes spatial distribution of ZnO in ways that are unpredicted by Zn anode models.

25 ENERGY STORAGE↗

DOE OSTI2022

Visualizing electrode assembly movement and lithiation heterogeneity in lithium-metal batteries using operando energy dispersive X-ray diffraction

There is renewed interest in Li-metal anodes in order to increase the energy density of battery cells. Here, we demonstrate an operando X-ray crystallography method to visualize lithiation gradients and electrode assembly movement during electrochemical cycling of a Li-metal cell containing a Ni-Mn-Co layered oxide cathode (NMC811). During charge, deposition of Li + ions from the cathode increases the Li foil thickness; during discharge, the thickness decreases as Li + ions are stripped off the foil. Additionally, the resulting periodic movement is observed through tracking of Bragg peaks from the ordered phases of the cathode and separator. In addition to this 3.6 μm/mAh displacement, continuous mossy Li build-up on the anode causes an irreversible drift of the assembly, which is similar to 11.3 μm/cycle. Furthermore, our data indicate significant lithiation gradients in the NMC811 cathode during the oxide relithiation, which is not observed during the delithiation.

25 ENERGY STORAGE↗

DOE OSTI2022

Unveiling Charge Transport and Degradation Mechanisms of Aqueous Zn|α-MoO 3 Batteries in Conventional Concentration and Water-in-Salt Electrolytes: A Multi-Modal In Situ and Operando Study

Herein charge storage and transport properties are elucidated and cell degradation mechanisms of rechargeable aqueous Zn|alpha-MoO 3 batteries in three electrolyte systems (3 m ZnSO 4 , 3 m ZnCl 2 , and 30 m ZnCl 2 [12.5 m] water-in-salt (WIS)) are distinguished by a combination of in situ X-ray diffraction (XRD), in situ X-ray absorption spectroscopy (XAS), operando optoelectrochemistry, and operando energy dispersive X-ray diffraction (EDXRD). In conventional concentration 3 m electrolytes, in situ XRD and XAS, as well as ex situ scanning transmission electron microscopy data collectively support Zn 2+ as the primary charge carrier. In addition, these systems are susceptible to cathode dissolution, Zn corrosion coupled with the hydrogen evolution reaction, and the resultant formation of basic zinc salt phases. The multi-modal in situ and operando experimental analyses validate facile H+ intercalation and extraction in concentrated 30 m ZnCl 2 WIS electrolyte. Via operando EDXRD, reaction front and charge transport limitation during discharge and charge in the viscous WIS electrolyte are spatially tracked. Here this work provides new insight into the stability and degradation mechanisms of aqueous zinc batteries during static storage and upon dynamic cycling, and highlights the utility of in situ and operando techniques in understanding the superior stability of WIS electrolytes.

25 ENERGY STORAGE↗

DOE OSTI2021

Generation of electric-field stabilized zirconium monoxide secondary phase within cubic zirconia

Flash sintering of cubic yttria-stabilized zirconia has been studied via in situ energy dispersive diffraction. A secondary rocksalt-phase zirconium monoxide was observed emerging from the primary fluorite-phase zirconium dioxide, previously only observed as a thin interlayer at metal-oxide interfaces, upon application of a direct current electric field. The average secondary phase intensity rose over extended flow of direct current through the ceramic, faded upon removal of the field and disappeared entirely upon application of an alternating current electric field. The results indicate that the sustained application of a direct current electric field can result in significant electrochemical reduction of zirconia under high current density conditions. Poor sinterability and cracking under direct current is apparent and potential mechanisms discussed therein.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Spatially-resolved lithiation dynamics from operando X-ray diffraction and electrochemical modeling of lithium-ion cells

In this study, energy dispersive X-ray diffraction is used to profile the time evolution of ordered Li x C 6 phases in solid electrodes of lithium-ion cells charged at rates between 0.2 and 4.7C (where 1C corresponds to full discharge in 1 h). The methods for quantifying lithium concentration in these phases from the acquired diffraction patterns are described. Compact expressions for time-dependent concentration gradients in the solid electrodes using orthogonal polynomial expansions are presented. Experimentally, these gradients persisted in lithiated graphite electrodes even after the cells rested at open-circuit for over 9 h. A multiphase electrochemical model of graphite intercalation captured many of the observed behaviors, including the progression of phase transitions and the persistent gradients at zero current. However, the magnitude of concentration gradients in both the oxide cathode and graphite anode is underestimated by the model, even at moderate currents.

25 ENERGY STORAGE↗

DOE OSTI2020

In situ X-ray spatial profiling reveals uneven compression of electrode assemblies and steep lateral gradients in lithium-ion coin cells

Coin cells are used extensively as test devices in battery research for evaluation of new materials and optimization of cycling protocols. Here, in situ X-ray diffraction profilometry is used to characterize spatial distribution of the active materials, lithiation, and phase distribution in electrodes of NCM523/graphite coin cells. The X-ray data indicate uneven areal compression of the electrode assembly in such cells, which we trace to a specific design feature that leads to elastic deformation of a metal spacer. Steep lithiation gradients observed in the electrodes imply radially-dependent resistivity, for which uneven compression of the separator is a likely cause. Electrochemical model calculations suggest that variable porosity of the polymer separator would account for the salient features of spatial profiles observed in these coin cells.

25 ENERGY STORAGE↗

DOE OSTI2020

Bismuth Enables the Formation of Disordered Birnessite in Rechargeable Alkaline Batteries

Recent advances in rechargeable Zn/MnO$_2$ alkaline batteries have shown promise for scalable energy storage systems which provide a safe, low-cost alternative with a demonstrated lifetime over thousands of cycles. This cathode technology is based on a 2-electron Mn redox process where a layered birnessite-type phase has been shown to form after the first cycle with excellent reversibility between the discharge product, Mn(OH)$_2$. Herein, we investigate the reversible reaction between birnessite and Mn(OH)$_2$ with and without a Bi$_2$O$_3$ additive using multimodal structural characterization techniques during active battery cycling. Diffraction results provide evidence of Bi$^{3+}$ residing in the interlayer of birnessite which prevents irreversible Mn$_3$O$_4$ formation by limiting Mn$^{3+}$ diffusion within the crystal lattice. Also, upon charge no MnOOH intermediate phases are observed. Instead, X-ray absorption and Raman spectroscopy indicate a disordered, non-crystalline birnessite-type phase consisting of mostly neutral H$_2$O within the interlayer. Birnessite phases will reform without Bi$_2$O$_3$ present, but Mn$_3$O$_4$ formation severely polarizes the potential they are formed at, leading to capacity fade. Also, we discuss the reversible Bi$_2$O$_3$ conversion to Bi$^0$ and its contribution to the observed capacity. We expect the results will provide crucial insight into the development of aqueous, rechargeable battery systems utilizing MnO 2 .

25 ENERGY STORAGE↗

DOE OSTI2020

Engineering lithium-ion battery cathodes for high-voltage applications using electromagnetic excitation

Microwave radiation (MWR), a type of electromagnetic excitation source, reduces the synthesis temperature and processing time for chemical reactions compared to traditional synthesis methods. Recently, we demonstrated that MWR can engineer ceramics with different crystal phases compared to traditional methods [ Journal of Materials Chemistry A 5 , 35 (2017)]. Here, we further apply the MWR-assisted technique to improve the electrochemical performance of LiCoO 2 cathodes by engineering TiO 2 and ZrO 2 ceramic coatings. Electrochemical tests suggest that the TiO 2 coating improves the rate capability of the LiCoO 2 electrode. Both TiO 2 and ZrO 2 coatings improve the high-voltage (4.5 V) cycling stability of LiCoO 2 . The capacity remaining is improved from 52.8 to 84.4% and 81.9% by the TiO 2 coating and the ZrO 2 coating, respectively, after 40 cycles. We compare these results with existing studies that apply traditional methods to engineer TiO 2 /ZrO 2 on LiCoO 2 , and find that the MWR-assisted method shows better performance improvement. X-ray photoelectron spectroscopy measurements suggest that the improved cycling stability arises from the formation of metal fluorides that protect the electrode from side reactions with electrolytes. This mechanism is further supported by the reduced Co dissolution from TiO 2 /ZrO 2 -coated LiCoO 2 electrode after cycling. This study provides a new toolbox facilitating the integration of many delicate, low melting point materials like polymers into battery electrodes.

25 ENERGY STORAGE↗

DOE OSTI2020

Development of a High-Rate Front-End ASIC for X-Ray Spectroscopy and Diffraction Applications

We developed a new front-end application-specific integrated circuit (ASIC) to upgrade the Maia X-ray microprobe. The ASIC instruments 32 configurable channels that perform either positive or negative charge amplification, pulse shaping, peak amplitude, and time extraction along with buffered analog storage. At a gain of 3.6 V/fC, 1-μs peaking time, and a temperature of 248 K, an electronic resolution of 13 and 10 e- rms was measured with and without a silicon drift detector (SDD) sensor, respectively. A spectral resolution of 170-eV full-width at half-maximum (FWHM) at 5.9 keV was obtained with an 55Fe source. The channel linearity was better than ± 1% with rate capabilities up to 40 kcps. The ASIC was fabricated in a commercial 250-nm process with a footprint of 6.3 mm × 3.9 mm and dissipates 167 mW of static power.

Vernon, Emerson↗