Engineering Papers⌕ Search

Engineering topics

Nukala, Phani K

Publications and source records attributed to Nukala, Phani K.

A parallel multigrid preconditioner for the simulation of large fracture networks

Computational modeling of a fracture in disordered materials using discrete lattice models requires the solution of a linear system of equations every time a new lattice bond is broken. Solving these linear systems of equations successively is the most expensive part of fracture simulations using large three-dimensional networks. In this paper, we present a parallel multigrid preconditioned conjugate gradient algorithm to solve these linear systems. Numerical experiments demonstrate that this algorithm performs significantly better than the algorithms previously used to solve this problem.

99 GENERAL AND MISCELLANEOUS↗

An algorithm for simulating fracture of cohesive-frictional materials

Fracture of disordered frictional granular materials is dominated by interfacial failure response that is characterized by de-cohesion followed by frictional sliding response. To capture such an interfacial failure response, we introduce a cohesive-friction random fuse model (CFRFM), wherein the cohesive response of the interface is represented by a linear stress-strain response until a failure threshold, which is then followed by a constant response at a threshold lower than the initial failure threshold to represent the interfacial frictional sliding mechanism. This paper presents an efficient algorithm for simulating fracture of such disordered frictional granular materials using the CFRFM. We note that, when applied to perfectly plastic disordered materials, our algorithm is both theoretically and numerically equivalent to the traditional tangent algorithm (Roux and Hansen 1992 J. Physique II 2 1007) used for such simulations. However, the algorithm is general and is capable of modeling discontinuous interfacial response. Our numerical simulations using the algorithm indicate that the local and global roughness exponents ({zeta}{sub loc} and {zeta}, respectively) of the fracture surface are equal to each other, and the two-dimensional crack roughness exponent is estimated to be {zeta}{sub loc} = {zeta} = 0.69 {+-} 0.03.

36 MATERIALS SCIENCE↗

Scaling of surface roughness in perfectly plastic disordered media

This paper investigates surface roughness characteristics of localized plastic yield surface in a perfectly plastic disordered material. We model the plastic disordered material using perfectly plastic random spring model. Our results indicate that plasticity in a disordered material evolves in a diffusive manner until macroscopic yielding, which is in contrast to the localized failure observed in brittle fracture of disordered materials. On the other hand, the height-height fluctuations of the plastic yield surfaces generated by the spring model exhibit roughness exponents similar to those obtained in the brittle fracture of disordered materials, albeit anomalous scaling of plastic surface roughness is not observed. The local and global roughness exponents ({zeta}{sub loc} and {zeta}, respectively) are equal to each other, and the two-dimensional crack roughness exponent is estimated to be {zeta}{sub loc} = {zeta} = 0.67 {+-} 0.03. The probability density distribution p[{Delta}h({ell})] of the height differences {Delta}h({ell}) = [h(x+{ell})-h(x)] of the crack profile follows a Gaussian distribution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Modeling of Gap Closure in Uranium-Zirconium Alloy Metal Fuel - A Test Problem

Uranium based binary and ternary alloy fuel is a possible candidate for advanced fast spectrum reactors with long refueling intervals and reduced liner heat rating [1]. An important metal fuel issue that can impact the fuel performance is the fuel-cladding gap closure, and fuel axial growth. The dimensional change in the fuel during irradiation is due to a superposition of the thermal expansion of the fuel due to heating, volumetric changes due to possible phase transformations that occur during heating and the swelling due to fission gas retention. The volumetric changes due to phase transformation depend both on the thermodynamics of the alloy system and the kinetics of phase change reactions that occur at the operating temperature. The nucleation and growth of fission gas bubbles that contributes to fuel swelling is also influenced by the local fuel chemistry and the microstructure. Once the fuel expands and contacts the clad, expansion in the radial direction is constrained by the clad, and the overall deformation of the fuel clad assembly depends upon the dynamics of the contact problem. The neutronics portion of the problem is also inherently coupled with microstructural evolution in terms of constituent redistribution and phase transformation. Because of the complex nature of the problem, a series of test problems have been defined with increasing complexity with the objective of capturing the fuel-clad interaction in complex fuels subjected to a wide range of irradiation and temperature conditions. The abstract, if short, is inserted here before the introduction section. If the abstract is long, it should be inserted with the front material and page numbered as such, then this page would begin with the introduction section.

36 MATERIALS SCIENCE↗

Mechanical modeling of porous oxide fuel pellet A Test Problem

A poro-elasto-plastic material model has been developed to capture the response of oxide fuels inside the nuclear reactors under operating conditions. Behavior of the oxide fuel and variation in void volume fraction under mechanical loading as predicted by the developed model has been reported in this article. The significant effect of void volume fraction on the overall stress distribution of the fuel pellet has also been described. An important oxide fuel issue that can have significant impact on the fuel performance is the mechanical response of oxide fuel pellet and clad system. Specifically, modeling the thermo-mechanical response of the fuel pellet in terms of its thermal expansion, mechanical deformation, swelling due to void formation and evolution, and the eventual contact of the fuel with the clad is of significant interest in understanding the fuel-clad mechanical interaction (FCMI). These phenomena are nonlinear and coupled since reduction in the fuel-clad gap affects thermal conductivity of the gap, which in turn affects temperature distribution within the fuel and the material properties of the fuel. Consequently, in order to accurately capture fuel-clad gap closure, we need to account for fuel swelling due to generation, retention, and evolution of fission gas in addition to the usual thermal expansion and mechanical deformation. Both fuel chemistry and microstructure also have a significant effect on the nucleation and growth of fission gas bubbles. Fuel-clad gap closure leading to eventual contact of the fuel with the clad introduces significant stresses in the clad, which makes thermo-mechanical response of the clad even more relevant. The overall aim of this test problem is to incorporate the above features in order to accurately capture fuel-clad mechanical interaction. Because of the complex nature of the problem, a series of test problems with increasing multi-physics coupling features, modeling accuracy, and complexity are defined with the objective of accurate simulation of fuel-clad mechanical interaction subjected to a wide-range of thermomechanical stimuli.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Time-parallel multiscale/multiphysics framework

We introduce the time-parallel compound wavelet matrix method (tpCWM) for modeling the temporal evolution of multiscale and multiphysics systems. The method couples time parallel (TP) and CWM methods operating at different spatial and temporal scales. We demonstrate the efficiency of our approach on two examples: a chemical reaction kinetic system and a non-linear predator prey system. Our results indicate that the tpCWM technique is capable of accelerating time-to-solution by 2 3-orders of magnitude and is amenable to efficient parallel implementation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fast update algorithm for the quantum Monte Carlo simulation of the Hubbard model

This paper presents an efficient algorithm for computing the transition probability in auxiliary field quantum Monte Carlo simulations of strongly correlated electron systems using a Hubbard model. This algorithm is based on a low rank updating of the underlying linear algebra problem, and results in significant computational savings. The computational complexity of computing the transition probability and Green s function update reduces to O(k2) during the kth step, where k is the number of accepted spin flips, and results in an algorithm that is faster than the competing delayed update algorithm. Moreover, this algorithm is orders of magnitude faster than traditional algorithms that use naive updating of the Green s function matrix.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗