Engineering Papers⌕ Search

Engineering topics

Northam, G. B.

Publications and source records attributed to Northam, G. B..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Development and evaluation of a plasma jet flameholder for scramjets

The objective of the work reported herein was to explore the use of a continuous operation plasma torch as an ignitor and flameholder for scramjet combustion. This research was motivated by the desire to eliminate the use of pyrophoric or toxic ignition and/or combustion enhancement materials in operational aircraft or shipboard systems. The total temperatures and torch powers used to ignite/flamehold Mach 2 combustion with hydrogen, ethylene, ethane, and methane were determined. The minimum ignition total temperatures for the fuels tested were hydrogen - 1065 R (lowest test temperature); ethylene - 1500 R; ethane - 2000 R; methane - 2700 R. These temperatures were obtained while operating the torch at a nominal 2 kw net power. The torch was shown to be a good ignitor and flameholder in that both hydrogen and hydrocarbon fuels could be stabilized by the torch and would 'blow off' when the torch was extinguished. The effectiveness of the torch was very sensitive to relative fuel injection location. Best combustion resulted when fuel was injected both upstream and downstream of the torch. These results indicated that an adiabatic plasma torch operating at about 2 kw could be an effective ignitor and flameholder for high-speed combustion.

Northam, G. B.↗
NASA NTRS1980

Flameholding characteristics of a swept-strut H2 fuel-injector for scramjet applications

A series of direct-connect tests are conducted which simulate the flow around the center swept-strut fuel-injector of a scramjet engine module. The experimental geometry includes both perpendicular and parallel fuel injectors which are swept with respect to the upstream flow direction in a manner simulating the flow geometry in the combustion region of the scramjet module. Seven different strut injector geometries are evaluated for their performance, flameholding, and inlet-combustor interaction characteristics. The most efficient combustion process is exhibited by the configuration having the deepest step with perpendicular injector orifices located 3.5 to 4.5 step heights downstream from the step. However, long centerbody and staged injection configurations perform as equally well as the deep step configuration when evaluating only the amount of perpendicular fuel injection. Since the staged injection configuration exhibits the lowest ignition and flameholding limit, it is suggested that the optimum injection configuration should incorporate a deep step with staged injection in order to improve the low temperature autoignition-flameholding characteristics.

Northam, G. B.↗
NASA NTRS1979

Lidar backscattering measurements of background stratospheric aerosols

A comparative lidar-dustsonde experiment was conducted in San Angelo, Texas, in May 1974 in order to estimate the uncertainties in stratospheric-aerosol backscatter for the NASA Langley 48-inch lidar system. The lidar calibration and data-analysis procedures are discussed. Results from the Texas experiment indicate random and systematic uncertainties of 35 and 63 percent, respectively, in backscatter from a background stratospheric-aerosol layer at 20 km.

Remsberg, E. E.↗
NASA NTRS1978

Characterization of a swept-strut hydrogen fuel-injector for scramjet applications

Results of an experimental investigation of a swept-strut hydrogen fuel-injector simulating the center strut of a three strut scramjet module at Mach 6 flight conditions are presented. Detailed wall pressure distributions from over 100 separate tests with overall fuel flow from 0.1 to 1.3 times stoichiometric and test gas stagnation temperature from 1100 to 2400 K were recorded. The distance for pressure rise from the point of injection was found to increase with increasing test stagnation temperature. This trend indicates that chemical kinetics in the immediate region of perpendicular injection are not likely to be the mechanism controlling the onset of pressure rise. A fluid dynamic mechanism is suggested involving separation of the boundary layer downstream of injection which is forced upstream from the trailing edge by pressure rise due to combustion occurring in the base region of the strut. The results obtained indicate that the swept-strut fuel-injector concept can be adapted to a wide range of flight conditions by varying the amount of perpendicular fuel injection.

Northam, G. B.↗
NASA NTRS1977

Multiple-laser-energy detection system

Technique monitors energy output of each of four sequentially-pulsed dye lasers for the Airborne LIDAR Oceanographic Probing Experiment system. Fiber optics attached to output mirrors transmit optical signal proportional to output energy.

Jarrett, O., Jr.↗
NASA NTRS1976

Lidar measurement of stratospheric dust from St. Augustine Volcano

The detection of a stratospheric dust layer of probable volcanic origin over Hampton, Va., on the evening of Jan. 28, 1976, with a 20-inch lidar system is reported. A digitized cathode-ray-tube trace of a return signal from altitudes of 12 to 24 km on January 28 is provided, and it is shown that 38% of the return was due to stratospheric aerosol. Noting that measurements on January 22 and February 2 showed no traces of this stratospheric dust layer, trajectories of dust-laden air parcels are followed from initiation at 0000 GMT on January 24 at the St. Augustine Volcano on Augustine Island, Alaska (59 deg N, 153 deg W). Analysis of the trajectories indicates that dust injected into the stratosphere at 59 deg N, 153 deg W could have been transported to Virginia in about 4 days. It is concluded that if the St. Augustine Volcano was the source of the dust, at least 23 deg of meridional transport from polar latitudes was observed.

Remsberg, E. E.↗
NASA NTRS1975

A comparison of dustsonde and LIDAR measurements of stratospheric aerosols

This paper describes the results and analysis of an experiment to compare the stratospheric aerosol profiles as measured by a balloon-borne in situ particle counter and by the backscattered light from a ground-based laser radar (LIDAR) operating at a wavelength of 6943 A. The profile comparison agrees within the experimental errors for particles with radii greater than 0.25 micrometer and for altitudes between 15 and 28 kilometers. Following the calibration tests, the LIDAR was used to monitor the stratospheric aerosols at Hampton, Virginia. Enhanced backscatter appeared sporadically in November and December of 1974 over Hampton; scattering ratios averaged over altitude increments of 450 meters range from 1.10 at 20 kilometers in early November to 3.3 at 17 kilometers on December 18. The source of this enhanced backscattering is attributed to the aerosols associated with the eruption of the Fuego volcano in Guatemala in mid-October.

Remsberg, E. E.↗
NASA NTRS1974

Dustsonde and lidar measurements of stratospheric aerosols - A comparison

Comparison of lidar and in situ measurements of stratospheric aerosol profiles obtained by backscattered ruby laser light and by direct in situ sampling over Laramie, Wyoming, on two nights in mid-September 1972. The lidar backscattering and the particle number density profiles correlated well. Based on these initial comparative experiments, the ground-based lidar coupled with temperature soundings appears to be a possible method for determining the relative aerosol profile under given stratospheric loading conditions.

Northam, G. B.↗
NASA NTRS1973

Comparison of Lidar and In-Situ Measurements of Stratospheric Aerosols

This paper will present the results of a comparative study conducted in Laramie, Wyoming, during the summer and fall of 1972, as part of the Department of Transportation's Climatic Impact Assessment Program (ClAP). The study included independent, and nearly simultaneous, measurements of stratospheric aerosols using a LIDAR system and a balloon-borne in-situ particle counter. The LIDAR provides a remote measurement of volume backscatter (aerosols and molecules) in a narrow wavelength region centered at the ruby wavelength (6943R); whereas the balloon-borne in-situ counter measures aerosol concentration by counting aerosols greater than approx. 0.30 microns in diameter as they are pumped through a chamber and scatter white light forward into photo-detectors. The comparison of measurements that will be discussed using the two techniques involves formulating the LIDAR data so that it is compatible with the counter data. The formulation includes separation of the scattering due to aerosols from the total and displaying this in terms of aerosol scattering function. Aerosol scattering function is proportional to aerosol concentration if the aerosol parameters, such as size distribution and composition, are constant with altitude. In separating the aerosol scattering from the total, the need for real atmospheric number density over the Standard Atmosphere is also discussed.

Melfi, S. H.↗
NASA NTRS1973

Tropospheric Transmissivity Measurements Using the Raman Nitrogen Lidar Technique

LIDAR measurements in Azusa, California, during October 1972, were made in which the backscattered Raman-shifted nitrogen return was ratioed at different altitudes in order to obtain transmissivity. Rawinsonde data from nearby El Monte were used to determine the temperature and nitrogen number density altitude profiles. These data and other meteorological data are compared to the vertical aerosol and transmissivity structure determined by LIDAR. Also data analysis techniques are shown for obtaining q2 (transmissivity) and beta (attenuation coefficient) as a function of altitude.

McCormick, M. P.↗
NASA NTRS1973

Effects of composition on acceleration induced burning-rate augmentation.

The objective of this work was to better define the effects of propellant composition variables on the acceleration induced burning-rate augmentation of solid propellants. The rate augmentation of an aluminized propellant at a given acceleration level was found to be a nonlinear inverse function of the reference or static burning rate and not controlled by binder or catalyst type at a given reference rate. A nonaluminized and a low rate double-base propellant exhibited strong transient rate augmentation due to surface pitting resulting from the retention of hot particles on the propellant surface.

Northam, G. B.↗
NASA NTRS1972

Effects of orientation of the acceleration vector on burning-rate augmentation

The functional dependence of acceleration-induced burning-rate augmentation on the magnitude and orientation of the acceleration vector was determined for an aluminized composite propellant by using a slab motor mounted at various angles on a centrifuge. The rate augmentation was strongly dependent on the orientation of the acceleration vector with respect to the burning propellant surface.

Northam, G. B.↗
NASA NTRS1972

Effects of propellant composition variables on acceleration-induced burning-rate augmentation of solid propellants

This work was conducted to define further the effects of propellant composition variables on the acceleration-induced burning rate augmentation of solid propellants. The rate augmentation at a given acceleration was found to be a nonlinear inverse function of the reference burning rate and not controlled by binder or catalyst type at a given reference rate. A nonaluminized propellant and a low rate double-base propellant exhibited strong transient rate augmentation due to surface pitting resulting from the retention of hot particles on the propellant surface.

Northam, G. B.↗
NASA NTRS1972

Effects of normal acceleration on transient burning rate augmentation of an aluminized solid propellant

Instantaneous burning rate data for a polybutadiene acrylic acid propellant, containing 16 weight percent aluminum, were calculated from the pressure histories of a test motor with 96.77 sq cm of burning area and a 5.08-cm-thick propellant web. Additional acceleration tests were conducted with reduced propellant web thicknesses of 3.81, 2.54, and 1.27 cm. The metallic residue collected from the various web thickness tests was characterized by weight and shape and correlated with the instantaneous burning rate measurements. Rapid depressurization extinction tests were conducted in order that surface pitting characteristics due to localized increased burning rate could be correlated with the residue analysis and the instantaneous burning rate data. The acceleration-induced burning rate augmentation was strongly dependent on propellant distance burned, or burning time, and thus was transient in nature. The results from the extinction tests and the residue analyses indicate that the transient rate augmentation was highly dependent on local enhancement of the combustion zone heat feedback to the surface by the growth of molten residue particles on or just above the burning surface. The size, shape, and number density of molten residue particles, rather than the total residue weight, determined the acceleration-induced burning rate augmentation.

Northam, G. B.↗
NASA NTRS1971

Effects of the acceleration vector on transient burning rate of an aluminized solid propellant.

Experimental results concerning the transient burning-rate augmentation of a 16% aluminum polybutadiene acrylic acid (PBAA) propellant burned in a 2-in. web motor at pressure levels from 300 to 1200 psia with centrifugal accelerations from 0 to 140 g. The orientation of the acceleration vector was varied to determine its effect on the transient burning rate. The burning-rate augmentation was strongly dependent on (1) acceleration level, (2) propellant distance burned (or burn time), and (3) orientation of the acceleration vector with respect to the burning surface. This transient rate augmentation resulted from the retention of molten metallic residue on the burning surface by the normal acceleration loading. The presence of the residue altered the combustion zone heat transfer and caused increased localized burning rates, as evidenced by the pitted propellant surfaces that were observed from extinction tests conducted at various acceleration levels.

Northam, G. B.↗