Engineering Papers⌕ Search

Engineering topics

Norgren, C. T.

Publications and source records attributed to Norgren, C. T..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Small gas turbine combustor experimental study - Compliant metal/ceramic liner and performance evaluation

Combustor research relating to the development of fuel efficient small gas turbine engines capable of meeting future commercial and military aviation needs is currently underway at NASA Lewis. As part of this combustor research, a basic reverse-flow combustor has been used to investigate advanced liner wall cooling techniques. Liner temperature, performance, and exhaust emissions of the experimental combustor utilizing compliant metal/ceramic liners were determined and compared with three previously reported combustors that featured: (1)splash film-cooled liner walls; (2) transpiration cooled liner walls; and (3) counter-flow film cooled panels.

Acosta, W. A.↗
NASA NTRS1986

Composite Refractory Felt/Ceramic Material

Ceramic protective coatings on combustor liners adhere better. Report discloses results of recent combustor-liner research where thick yttria stabilized zirconia ceramic was plasma-sprayed on BRUNSBOND substrates and exposed to nearly stoichiometric combustion. Combustor screening tests exposed 30 test specimens to nearly-stoichiometric flame temperatures of 3,450 degrees F (2,170 K) for 4 cycles. After completion of screening tests, all 30 specimens showed no visible evidence of discoloration or failure. There were no mudflat cracks, felt/ceramic, or backing/felt separations on any panels.

Ercegovic, D. B.↗
NASA NTRS1986

Small gas turbine combustor experimental study: Compliant metal/ceramic liner and performance evaluation

Combustor research relating to the development of fuel efficient small gas turbine engines capable of meeting future commercial and military aviation needs is currently underway at NASA Lewis. As part of this combustor research, a basic reverse-flow combustor has been used to investigate advanced liner wall cooling techniques. Liner temperature, performance, and exhaust emissions of the experimental combustor utilizing compliant metal/ceramic liners were determined and compared with three previously reported combustors that featured: (1) splash film-cooled liner walls; (2) transpiration cooled liner walls; and (3) counter-flow film cooled panels.

Acosta, W. A.↗
NASA NTRS1985

Advanced liner-cooling techniques for gas turbine combustors

Component research for advanced small gas turbine engines is currently underway at the NASA Lewis Research Center. As part of this program, a basic reverse-flow combustor geometry was being maintained while different advanced liner wall cooling techniques were investigated. Performance and liner cooling effectiveness of the experimental combustor configuration featuring counter-flow film-cooled panels is presented and compared with two previously reported combustors featuring: splash film-cooled liner walls; and transpiration cooled liner walls (Lamilloy).

Norgren, C. T.↗
NASA NTRS1985

Small gas turbine combustor study - Fuel injector performance in a transpiration-cooled liner

The effect of fuel injection technique on the performance of an advanced reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) was determined. Performance and emission levels are documented over a range of simulated flight conditions using simplex pressure atomizing, spill return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types is obtained.

Riddlebaugh, S. M.↗
NASA NTRS1985

Advanced liner-cooling techniques for gas turbine combustors

Component research for advanced small gas turbine engines is currently underway at the NASA Lewis Research Center. As part of this program, a basic reverse-flow combustor geometry was being maintained while different advanced liner wall cooling techniques were investigated. Performance and liner cooling effectiveness of the experimental combustor configuration featuring counter-flow film-cooled panels is presented and compared with two previously reported combustors featuring: splash film-cooled liner walls; and transpiration cooled liner walls (Lamilloy).

Norgren, C. T.↗
NASA NTRS1985

Small gas turbine combustor study: Fuel injector performance in a transpiration-cooled liner

The effect of fuel injection technique on the performance of an advanced reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) was determined. Performance and emission levels are documented over a range of simulated flight conditions using simplex pressure atomizing, spill return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types is obtained.

Riddlebaugh, S. M.↗
NASA NTRS1984

Ceramic composite liner material for gas turbine combustors

Advanced commercial and military gas turbine engines may operate at combustor outlet temperatures in excess of 1920 K (3000 F). At these temperatures combustors liners experience extreme convective and radiative heat fluxes. The ability of a plasma sprayed ceramic coating to reduce liner metal temperature has been recognized. However, the brittleness of the ceramic layer and the difference in thermal expansion with the metal substrate has caused cracking, spalling and some separation of the ceramic coating. Research directed at turbine tip seals (or shrouds) has shown the advantage of applying the ceramic to a compliant metal pad. This paper discusses recent studies of applying ceramics to combustor liners in which yttria stabilized zirconia plasma sprayed on compliant metal substrates which were exposed to near stoichiometric combustion, presents performance and durability results, and describes a conceptual design for an advanced, small gas turbine combustor. Test specimens were convectively cooled or convective-transpiration cooled and were evaluated in a 10 cm square flame tube combustor at inlet air temperatures of 533 K (500 F) and at a pressure of 0.5 MPa (75 psia). The ceramics were exposed to flame temperatures in excess of 2000 K (3320 F). Results appear very promising with all 30 specimens surviving a screening test and one of two specimens surviving a cyclic durability test.

Ercegovic, D. B.↗
NASA NTRS1984

Ceramic composite liner material for gas turbine combustors

The application of ceramics to gas turbine combustor liners to reduce liner metal temperature was studied in an experiment in which yttria-stabilized zirconia plasma was sprayed on compliant metal substrates exposed to near stoichiometric combustion. The strain isolation pad materials chosen were Hoskins Alloy 875 and BRUNSLLOY 534 Fiber Metal of 0.25 and 0.38 cm thicknesses and 35 and 45 percent density levels. Combustor screening tests of all specimens showed no evidence of deterioration or failure. Specimens exposed to flame temperatures in excess of 2100 K were convectively or convective-transpiration cooled and were evaluated in a 10 cm sq flame tube at inlet air temperature of 533 K and pressure of 0.5 MPa. The results suggest the superiority of a system composed of the Hoskins Alloy 875 compliant pad with 0.25 cm thickness and 35 percent density coupled with a NiCrAlY bond coat and a 8 percent Y2O3-ZrO2 ceramic top coat of 0.19 cm thickness.

Ercegovic, D. B.↗
NASA NTRS1983

Effect of broad properties fuel on injector performance in a reverse flow combustor

The effect of fuel type on the performance of various fuel injectors was investigated in a reverse flow combustor. Combustor performance and emissions are documented for simplex pressure atomizing, spill flow, and airblast fuel injectors using a broad properties fuel and compared with performance using Jet A fuel. Test conditions simulated a range of flight conditions including sea level take off, low and high altitude cruise, as well as a parametric evaluation of the effect of increased combustor loading. The baseline simplex injector produced higher emission levels with corresponding lower combustion efficiency with the broad properties fuel. There was little or not loss in performance by the two advanced concept injectors with the broad properties fuel. The airblast injector proved to be especially insensitive to fuel type.

Raddlebaugh, S. M.↗
NASA NTRS1983

Small gas turbine combustor study - Combustor liner evaluation

A reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) is compared both analytically and experimentally with a conventional splash film-cooled design with the same combustor configuration. Comparison of selected critical combustor panels indicated that it was possible to maintain the liner temperature similar between the two configurations using 50 percent less coolant for the Lamilloy as compared with the reference film-cooled combustor. Additional benefits indicated improvement in outlet temperature distribution and NOx emission level.

Norgren, C. T.↗
NASA NTRS1981

Effect of fuel injector type on performance and emissions of reverse-flow combustor

The combustion process in a reverse-flow combustor suitable for a small gas turbine engine was investigated to evaluate the effect of fuel injector type on performance and emissions. Fuel injector configurations using pressure-atomizing, spill-flow, air blast, and air-assist techniques were compared and evaluated on the basis of performance obtained in a full-scale experimental combustor operated at inlet conditions corresponding to takeoff, cruise, low power, and idle and typical of a 16:1-pressure-ratio turbine engine. Major differences in combustor performance and emissions characteristics were experienced with each injector type even though the aerodynamic configuration was common to most combustor models. Performance characteristics obtained with the various fuel injector types could not have been predicted from bench-test injector spray characteristics. The effect of the number of operating fuel injectors on performance and emissions is also presented.

Norgren, C. T.↗
NASA NTRS1981

Small gas-turbine combustor study - Fuel injector evaluation

As part of a continuing effort at the Lewis Research Center to improve performance, emissions, and reliability of turbine machinery, an investigation was undertaken to determine the effect of fuel injection technique and fuel type on similar improvements for small gas-turbine combustors. Performance and pollutant emission levels are documented over a range of simulated flight conditions for a reverse-flow combustor configuration using simplex pressure-atomizing, spill-flow return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types was obtained. Jet A and an experimental referee broad specification fuel were used to determine and compare effects of burning different types of fuels in a small experimental gas turbine combustor.

Norgren, C. T.↗
NASA NTRS1981

Small gas-turbine combustor study: Fuel injector evaluation

As part of a continuing effort at the Lewis Research Center to improve performance, emissions, and reliability of turbine machinery, an investigation of fuel injection technique and effect of fuel type on small gas turbine combustors was undertaken. Performance and pollutant emission levels are documented over a range of simulated flight conditions for a reverse flow combustor configuration using simplex pressure-atomizing, spill-flow return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types was obtained. Jet A and an experimental referee broad specification fuel were used to determine the effect of fuel type.

Norgren, C. T.↗
NASA NTRS1978

Reverse-flow combustor for small gas turbines with pressure-atomizing fuel injectors

A reverse flow combustor suitable for a small gas turbine (2 to 3 kg/s mass flow) was used to evalute the effect of pressure atomizing fuel injectors on combustor performance. In these tests an experimental combustor was designed to operate with 18 simplex pressure atomizing fuel injectors at sea level takeoff conditions. To improve performance at low power conditions, fuel was redistributed so that only every other injector was operational. Combustor performance, emissions, and liner temperature were compared over a range of pressure and inlet air temperatures corresponding to simulated idle, cruise, and takeoff conditions typical of a 16 to 1 pressure ratio turbine engine.

Norgren, C. T.↗
NASA NTRS1976

Spectral radiance measurements and calculated soot concentrations along the length of an experimental combustor

Radiometric data were obtained over a range of parametric test conditions at three positions along the length of an experimental combustor segment corresponding to the primary, intermediate, and dilution zones. The concentration of soot entrained in the combustion gases was calculated by a technique using spectral radiance measurements. Tests were conducted primarily with Jet A fuel, although limited data were taken with two fuels having higher aromatic content, diesel oil number 2 and a blend of 40 percent tetralin in Jet A fuel. Radiometric observation of the combustion gases indicated that the maximum total radiance peaked at the intermediate zone, which was located immediately upstream of the dilution holes. Soot concentrations calculated from optical measurements in the dilution zone compared favorably with those obtained by in situ gas sampling at the exhaust. The total radiance increased with the higher aromatic content fuels.

Norgren, C. T.↗