Geometric Challenges in Designing Parts for Machining Using Wire-fed DED
Explore the source record for details and available documents.
Vaughan, Derek↗
Engineering topics
Noakes, Mark
Publications and source records attributed to Noakes, Mark.
Effective residual stress prediction validated with neutron diffraction method for metal large-scale additive manufacturing
Not Available
36 MATERIALS SCIENCE↗
Supervisory control and health monitoring framework for large-scale additive manufacturing systems. Final CRADA report
ORNL worked with National Instruments (NI) to develop a large-scale, complex additive manufacturing (AM) systems framework for remote health monitoring and supervisory control. We found the framework, based on the Lincoln Electric Metal AM system located at ORNL’s MDF, capable of controlling the process, leading to improved part quality and digital twin creation.
42 ENGINEERING↗
Consumable development to tailor residual stress in parts fabricated using directed energy deposition processes
Distortion and residual stresses are major challenges that limit the ability to fabricate large scale structures using Additive Manufacturing (AM). Researchers worldwide are evaluating techniques to induce compressive residual stress in the parts via intermittent rolling. While reasonable success has been documented, the idea of lowering the martensite start temperature to induce compressive stresses has not been evaluated in the context of AM, despite demonstrated success by the welding community. This study validates the hypothesis that, by a proper selection of materials and process parameters, one may effectively reduce distortion and induce a compressive residual stress in AM parts. Using neutron diffraction to measure residual stresses in parts, we demonstrate that, in addition to selection of the correct materials, the inter pass temperature plays a major role in controlling the residual stress evolution. The observations relating to the residual stresses are rationalized based on a microstructural evolution in these samples. Based on this preliminary study, a strategy to fabricate large structures with minimal distortion and residual stress is outlined.
36 MATERIALS SCIENCE↗
Investigating the effect of different shielding gas mixtures on microstructure and mechanical properties of 410 stainless steel fabricated via large scale additive manufacturing
Metal Big Area Additive Manufacturing (mBAAM) offers the potential to fabricate large scale tools at high deposition rates (15 lb/h+). 410 martensitic steel is a potential tooling material, owing to its low cost, good machinability and reasonable printability. During the mBAAM process, the shielding gas can have a significant impact on the material properties as well as the process cost. Therefore, the current study aims to understand the effect of different shielding gas mixtures on large-scale additive manufacturing of 410 martensitic stainless steel. We show that an argon mixture with 3% nitrogen gas produced the best performance in terms of maximum hardness and tensile strength, with much less scatter in tensile strength. He-Ar-CO 2 or tri-mix shielded samples showed a low tensile strength with wide scatter, due to stabilized delta ferrite in microstructure during printing. Both tri-mix and Ar-CO 2 shielded samples showed slightly higher porosity. Thus, we recommend the use of argon-3% nitrogen as a shielding gas mixture for processing 410 steel for tool applications, based on the relatively low cost of this gas mixture and the resulting higher hardness, higher dimensional stability, and lower porosity.
36 MATERIALS SCIENCE↗
There’s plenty of room at the top
Richard Feynman’s famous words, “there’s plenty of room at the bottom,” referred to the opportunities for revolutionizing the electronics industry by developing the science and technology of how to manufacture very small components (sub-micron to nanometer sized features). In additive manufacturing (AM), the opposite may be true: There’s plenty of room at the top. AM’s strength is in the low volume production of complex components, which is demanded in big industries such as oil and gas, construction, tooling, wind and water turbines, and infrastructure. Is AM’s ‘big’ future in the manufacture of large structures? Here, this special issue surveys the technical challenges and enormous opportunities associated with large scale additive manufacturing while discussing the materials, processes and applications that are enabled by scaling to much larger structures, much faster speeds and lower manufacturing costs. The authors believe that, if Professor Feynman was alive, he’d say “There’s plenty of room at the top.”
36 MATERIALS SCIENCE↗
Mitigating Scatter in Mechanical Properties in AISI 410 Fabricated via Arc-Based Additive Manufacturing Process
Wire-based metal additive manufacturing utilizes the ability of additive manufacturing to fabricate complex geometries with high deposition rates (above 7 kg/h), thus finding applications in the fabrication of large-scale components, such as stamping dies. Traditionally, the workhorse materials for stamping dies have been martensitic steels. However, the complex thermal gyrations induced during additive manufacturing can cause the evolution of an inhomogeneous microstructure, which leads to a significant scatter in the mechanical properties, especially the toughness. Therefore, to understand these phenomena, arc-based additive AISI 410 samples were fabricated using robotic gas metal arc welding (GMAW) and were subjected to a detailed characterization campaign. The results show significant scatter in the tensile properties as well as Charpy V-notch impact toughness data, which was then correlated to the microstructural heterogeneity and delta (δ) ferrite formation. Post-processing (austenitizing and tempering) treatments were developed and an ~70% reduction in the scatter of tensile data and a four-times improvement in the toughness were obtained. The changes in mechanical properties were rationalized based on the microstructure evolution during additive manufacturing. Based on these, an outline to tailor the composition of “printable” steels for tooling with isotropic and uniform mechanical properties is presented and discussed.
36 MATERIALS SCIENCE↗
Dynamic stiffness modification by internal features in additive manufacturing
Dynamic stiffness, or the product of the modal stiffness and damping ratio, is an important consideration for the design of additively manufactured parts that will experience dynamic loading. Here, this paper describes a demonstration component which was designed and manufactured in two configurations using a metal wire arc additive process. The first configuration was an open channel structure, while the second contained a dynamic absorber in the internal cavity. Frequency response measurements of the two components showed a significant magnitude reduction for the modified component at the original open channel structure's natural frequency and an overall increase in dynamic stiffness. Polymer damping material was then added to further increase the dynamic stiffness.
Additive manufacturing↗
Phase stability and mechanical properties of wire + arc additively manufactured H13 tool steel at elevated temperatures
Wire + arc additive manufacturing (WAAM) is considered an innovative technology that can change the manufacturing landscape in the near future. WAAM offers the benefits of inexpensive initial system setup and a high deposition rate for fabricating medium- and large-sized parts such as die-casting tools. Here, AISI H13 tool steel, a popular die-casting tool metal, is manufactured by cold metal transfer (CMT)-based WAAM and is then comprehensively analyzed for its microstructural and mechanical properties. Location-dependent phase combinations are observed, which could be explained by nonequilibrium thermal cycles that resulted from the layer-by-layer stacking mechanism used in WAAM. In addition, remelting and reheating of the layers reduces welding anomalies (e.g., pores and voids). The metallurgical characteristics of the H13 strongly correlate with the mechanical properties. The combinations of phases at different locations of the additively manufactured part exhibit a periodic microhardness profile. Martensite, Retained Austenite, Ferrite, and Carbide phases are found in combination at different locations of the part based on the part’s temperature distribution during additive deposition. Moreover, the tensile properties at elevated temperatures (23 °C, 300 °C, and 600 °C) are comparable to those from other WAAM and additive manufacturing (AM) processes. The X-ray diffraction results verify that the microstructural stability of the fabricated parts at high temperatures would allow them to be used in high temperatures.
36 MATERIALS SCIENCE↗